ON NCP629FC18T2G High performance cmos ldo regulator with enable and enhanced esd protection in chip scale package (csp) Datasheet

NCP629
High Performance CMOS
LDO Regulator with Enable
and Enhanced ESD
Protection in Chip Scale
Package (CSP)
The NCP629 provides 150 mA of output current at fixed voltage
options. It is designed for portable battery powered applications and
offers high performance features such as low power operation, fast
enable response time, and low dropout.
The device is designed to be used with low cost ceramic capacitors.
Features
•Output Voltage Options:
1.5 V, 1.8 V, 2.8 V, 3.0 V, 3.3 V, 3.5 V, 5.0 V
•Ultra-Low Dropout Voltage of 150 mV at 150 mA
•Fast Enable Turn-on Time of 15 ms
•Wide Supply Voltage Operating Range
•Supports sub-1 V Enable Threshold
•Excellent Line and Load Regulation
•High Accuracy up to 2% Output Voltage Tolerance over All
Operating Conditions
•Typical Noise Voltage of 50 mVrms without a Bypass Capacitor
•Ultra Small CSP Footprint and Height: 1.028 x 1.19 mm,
Max Height 0.6 mm
•Enhanced ESD Protection (HBM 3.5 kV, MM 400 V)
•These are Pb-Free Devices
http://onsemi.com
MARKING
DIAGRAM
XXXG
AYWW
5 PIN FLIP-CHIP
CASE 499AY
XXX
A
Y
WW
G
= Specific Device Code
= Assembly Location
= Year
= Work Week
= Pb-Free Package
PIN CONNECTIONS
A3
C3
ÍÍÍ
ÍÍÍ
A1
B2
C1
(Top View)
Typical Applications
•Personal Electronics (MP3 Players)
•Portable Devices (Cellular Phones)
•Noise Sensitive Circuits – VCO, RF Stages, etc.
•Camcorders and Cameras
A3
C3
C1
B2
A1
= ENABLE
= Vin
= Vout
= NC
= GND (substrate)
ORDERING INFORMATION
Vin
Vout
NCP629
ENABLE
Vin
Cin
GND
Vout
See detailed ordering and shipping information in the
package dimensions section on page 10 of this data sheet.
Cout
Figure 1. Typical Application Circuit
© Semiconductor Components Industries, LLC, 2008
February, 2008 - Rev. 1
1
Publication Order Number:
NCP629/D
NCP629
Vin
Vout
Driver with
Current Limit
+
-
Vref
Thermal
Shutdown
GND
ENABLE
Figure 2. Simplified Block Diagram
PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
C3
Vin
A1
GND
A3
ENABLE
Description
Positive Power Supply Input
Power Supply Ground; Device Substrate
The Enable Input places the device into low-power standby when pulled to logic low (< 0.4 V).
Connect to Vin if the function is not used.
B2
NC
No Connection
C1
Vout
Regulated Output Voltage
ABSOLUTE MAXIMUM RATINGS
Symbol
Value
Unit
Input Voltage Range (Note 1)
Rating
Vin
-0.3 to 6.5
V
Output Voltage Range
Vout
-0.3 to 6.5 (or Vin + 0.3)
Whichever is Lower
V
ENABLE
-0.3 to 6.5 (or Vin + 0.3)
Whichever is Lower
V
TJ(max)
150
°C
TSTG
-65 to 150
°C
ESD Capability, Human Body Model (Note 2)
ESDHBM
3500
V
ESD Capability, Machine Model (Note 2)
ESDMM
400
V
MSL
MSL1/260
-
Enable Input Range
Maximum Junction Temperature
Storage Temperature Range
Moisture Sensitivity Level
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC-Q100-002 (EIA/JESD22-A114)
ESD Machine Model tested per AEC-Q100-003 (EIA/JESD22-A115)
Latchup Current Maximum Rating: ≤150 mA per JEDEC standard: JESD78.
THERMAL CHARACTERISTICS
Rating
Symbol
Thermal Characteristics (Note 3)
Thermal Resistance, Junction-to-Air (Note 4)
Value
Unit
°C/W
RqJA
277
3. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
4. Values based on copper area of 645 mm2, 1 oz copper thickness.
OPERATING RANGES (Note 5)
Symbol
Min
Max
Operating Input Voltage (Note 6)
Rating
Vin
1.5
6
V
Output Current
Iout
0
150
mA
Ambient Temperature
TA
-40
125
°C
5. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
6. Minimum Vin = 1.5 V or (Vout + VDO), whichever is higher.
http://onsemi.com
2
Unit
NCP629
ELECTRICAL CHARACTERISTICS
(Vin = Vout + 0.5 V, Cin = Cout =1.0 mF, for typical values TA = 25°C, for min/max values TA = -40°C to 125°C; unless otherwise noted.)
(Note 7)
Parameter
Test Conditions
Symbol
Output Voltage
1.5 V
1.8 V
2.8 V
3.0 V
3.3 V
3.5 V
5.0 V
Iout = 1.0 mA to 150 mA
Vin = (Vout + 0.5 V) to 6.0 V
Vout
Power Supply Ripple Rejection (Note 8)
(Vin = Vout + 1.0 V + 0.5 Vp-p)
Iout = 1.0 mA to 150 mA
f = 120 Hz
f = 1.0 kHz
f = 10 kHz
PSRR
Line Regulation
Vin = (Vout + 0.5 V) to 6.0 V,
Iout = 1.0 mA
Regline
Load Regulation
1.5 V
1.8 V
2.8 V to 5.0 V
Iout = 1.0 mA to 150 mA
Regload
Output Noise Voltage (Note 8)
Vout = 1.5 V,
f = 10 Hz to 100 kHz
Output Short Circuit Current
Vout = 0 V
Dropout Voltage
1.5 V
1.8 V
2.8 V to 5.0 V
Measured at: Vout – 2.0%
Iout = 150 mA
VDO
Disable Current
ENABLE = 0 V, Vin = 6 V
-40°C ≤ TA ≤ 85°C
IDIS
Ground Current
1.5 V
1.8 V to 3.0 V
3.3 V to 5.0 V
ENABLE = 0.9 V,
Iout = 1.0 mA to 150 mA
IGND
Min
Typ
Max
Unit
Regulator Output
V
1.470
1.764
2.744
2.940
3.234
3.430
4.900
(-2%)
1.530
1.836
2.856
3.060
3.366
3.570
5.100
(+2%)
dB
-
62
55
38
-
-
1.0
10
-
2.0
2.0
2.0
20
25
30
Vn
-
50
-
mVrms
Isc
300
550
800
mA
-
150
125
75
225
175
125
-
0.01
1.0
-
135
140
145
170
175
180
mV
mV
mV
General
mA
mA
Thermal Shutdown Temperature (Note 8)
TSD
-
175
-
°C
Thermal Shutdown Hysteresis (Note 8)
TSH
-
10
-
°C
Chip Enable
ENABLE Input Threshold Voltage
V
Vth(EN)
Voltage Increasing, Logic High
0.9
-
-
Voltage Decreasing, Logic Low
-
-
0.4
-
3.0
100
-
15
30
25
50
Enable Input Bias Current (Note 8)
IEN
nA
Timing
Output Turn On Time
1.5 V to 3.5 V
5.0 V
ENABLE = 0 V to Vin
ms
ton
7. Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at
TJ = TA = 25 °C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
8. Values based on design and/or characterization.
http://onsemi.com
3
NCP629
TYPICAL CHARACTERISTICS
1.500
1.500
Vout, OUTPUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE (V)
Iout = 1.0 mA
1.495
1.490
Iout = 150 mA
1.485
1.480
1.475
-40
-15
10
35
60
85
1.490
Iout = 150 mA
1.485
1.480
-15
10
35
60
85
110 125
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 3. Output Voltage vs. Temperature
(1.5 V Fixed Output, Vin = 2 V)
Figure 4. Output Voltage vs. Temperature
(1.5 V Fixed Output, Vin = 6 V)
3.005
Iout = 1.0 mA
3.000
2.995
Vout, OUTPUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE (V)
1.495
1.475
-40
110 125
3.005
Iout = 150 mA
2.990
2.985
2.980
2.975
-40
Iout = 1.0 mA
-15
10
35
60
85
110 125
Iout = 1.0 mA
3.000
2.995
2.990
Iout = 150 mA
2.985
2.980
2.975
2.970
-40
TA, AMBIENT TEMPERATURE (°C)
-15
10
35
60
85
110 125
TA, AMBIENT TEMPERATURE (°C)
Figure 5. Output Voltage vs. Temperature
(3.0 V Fixed Output, Vin = 3.5 V)
Figure 6. Output Voltage vs. Temperature
(3.0 V Fixed Output, Vin = 6 V)
http://onsemi.com
4
NCP629
TYPICAL CHARACTERISTICS
5.000
Iout = 1.0 mA
Vout, OUTPUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE (V)
5.000
4.995
4.990
Iout = 150 mA
4.985
4.980
4.975
Iout = 1.0 mA
4.995
4.990
4.985
Iout = 150 mA
4.980
4.975
4.970
4.970
4.965
-40
-15
10
35
60
110 125
85
4.965
-40
-15
TA, AMBIENT TEMPERATURE (°C)
60
85
110 125
Figure 8. Output Voltage vs. Temperature
(5.0 V Fixed Output, Vin = 6 V)
250
250
VDO, DROPOUT VOLTAGE (mV)
Vout = 1.5 V
200
Iout = 150 mA
150
Iout = 100 mA
100
Iout = 50 mA
50
Iout = 1 mA
0
-40 -20
0
20
40
60
80
100
Iout = 150 mA
200
Vout = 1.5 V
150
Vout = 3.0 V
100
50
Vout = 5.0 V
0
-40 -20
120
0
20
40
60
80
100
120
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 9. Dropout Voltage vs. Temperature
(Over Current Range)
Figure 10. Dropout Voltage vs. Temperature
(Over Output Voltage)
800
6.0
5.5
5.0
Iout = 0 mA
Cout = 1.0 mF
TA = 25°C
ENABLE = Vin
4.5
4.0
Vth(en), ENABLE THRESHOLD (mV)
VDO, DROPOUT VOLTAGE (mV)
35
TA, AMBIENT TEMPERATURE (°C)
Figure 7. Output Voltage vs. Temperature
(5.0 V Fixed Output, Vin = 5.5 V)
Vout, OUTPUT VOLTAGE (V)
10
5.0 V
3.3 V
3.0 V
3.5
3.0
2.80 V
2.5
2.0
1.80 V
1.5 V
1.5
1.0
0.5
0
0
1.0
2.0
3.0
4.0
5.0
6.0
750
Enable Increasing
700
Enable Decreasing
650
Vin = 5.5 V
600
-40
-15
10
35
60
85
110 125
Vin, INPUT VOLTAGE (V)
TA, AMBIENT TEMPERATURE (°C)
Figure 11. Output Voltage vs. Input Voltage
Figure 12. Enable Threshold vs. Temperature
http://onsemi.com
5
NCP629
TYPICAL CHARACTERISTICS
160
IGND, GROUND CURRENT (mA)
IDIS, DISABLE CURRENT (mA)
6.0
5.0
4.0
3.0
2.0
ENABLE = 0 V
1.0
0
-40
-15
10
35
60
85
110
Iout = 1.0 mA
150
Vout = 5.0 V
145
Iout = 150 mA
140
135
Iout = 1.0 mA
130
125
Vout = 1.5 V
120
Iout = 150 mA
115
ENABLE = 0.9 V
110
-40
125
-20
0
20
40
60
100
80
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 13. Ground Current (Sleep Mode) vs.
Temperature
Figure 14. Ground Current (Run Mode) vs.
Temperature
120
137
160
2.8 V
140
3.0 V
1.5 V
IGND, GROUND CURRENT (mA)
IGND, GROUND CURRENT (mA)
155
5.0 V
3.3 V
120
1.8 V
100
80
60
40
20
Vout = 1.5 V
Vin = 2.0 V
136
135
134
133
132
131
130
129
128
127
0
0
1.0
2.0
3.0
4.0
5.0
0
6.0
25
50
75
100
125
150
Vin, INPUT VOLTAGE (V)
Iout, OUTPUT CURRENT (mA)
Figure 15. Ground Current vs. Input Voltage
Figure 16. Ground Current vs. Output Current
http://onsemi.com
6
NCP629
700
650
ILIM, CURRENT LIMIT (mA)
Isc, OUTPUT SHORT CIRCUIT CURRENT (mA)
TYPICAL CHARACTERISTICS
600
550
500
450
-40 -20
400
300
200
100
20
40
60
80
100
0
120
1.0
2.0
3.0
5.0
4.0
TA, AMBIENT TEMPERATURE (°C)
Vin, INPUT VOLTAGE (V)
Figure 17. Output Short Circuit Current vs.
Temperature
Figure 18. Current Limit vs. Input Voltage
Regload, LOAD REGULATION (mV)
3.0
2.0
1.0
Vin = (Vout + 0.5 V) to 6.0 V
Iout = 1.0 mA
0
-40 -20
0
20
40
60
80
100
120
6.0
5.0
4.0
3.0
2.0
1.0
Iout = 1.0 mA to 150 mA
0
-40
-15
10
35
60
85
110 125
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 19. Line Regulation vs. Temperature
Figure 20. Load Regulation vs. Temperature
45
80
40
70
1.5 V
60
35
3.3 V
5.0 V
PSRR (dB)
Regline, LINE REGULATION (mV)
500
0
0
4.0
OUTPUT TURN ON TIME (mS)
600
30
25
3.0 V
20
1.5 V
50
40
5.0 V
30
Vin = Vout + 1.0 V
Vripple = 0.5 Vp-p
Cout = 1.0 mF
Iout = 1.0 mA to 150 mA
20
15
10
10
-40 -20
0
0
20
40
60
80
100
120
0.1
1.0
10
100
TA, AMBIENT TEMPERATURE (°C)
f, FREQUENCY (kHz)
Figure 21. Output Turn On Time vs.
Temperature
Figure 22. Power Supply Ripple Rejection vs.
Frequency
http://onsemi.com
7
NCP629
TYPICAL CHARACTERISTICS
OUTPUT CAPACITOR ESR (W)
10
Vout = 5.0 V
Unstable Region
Vout = 1.5 V
1.0
Stable Region
0.1
Cout = 1.0 mF to 10 mF
TA = -40°C to 125°C
Vin = up to 6.0 V
0.01
0
25
50
75
100
125
150
Iout, OUTPUT CURRENT (mA)
Figure 23. Output Stability with Output
Capacitor ESR over Output Current
Vout = 1.5 V
Figure 24. Load Transient Response (1.0 mF)
Vout = 1.5 V
Figure 25. Load Transient Response (10 mF)
http://onsemi.com
8
NCP629
DEFINITIONS
Load Regulation
Line Regulation
The change in output voltage for a change in output load
current at a constant temperature.
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse techniques such that the
average junction temperature is not significantly affected.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 2% below its
nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Line Transient Response
Typical output voltage overshoot and undershoot
response when the input voltage is excited with a given
slope.
Output Noise Voltage
Load Transient Response
This is the integrated value of the output noise over a
specified frequency range. Input voltage and output load
current are kept constant during the measurement. Results
are expressed in mVrms or nV/√Hz.
Typical output voltage overshoot and undershoot
response when the output current is excited with a given
slope between low-load and high-load conditions.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 175°C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Disable and Ground Current
Ground Current (IGND) is the current that flows through
the ground pin when the regulator operates with a load on its
output. This consists of internal IC operation, bias, etc. It is
actually the difference between the input current (measured
through the LDO input pin) and the output load current. If
the regulator has an input pin that reduces its internal bias
and shuts off the output (enable/disable function), this term
is called the disable current (IDIS.)
Maximum Package Power Dissipation
The power dissipation level at which the junction
temperature reaches its maximum operating value.
APPLICATIONS INFORMATION
The NCP629 series regulator is self-protected with
internal thermal shutdown and internal current limit. Typical
application circuit is shown in Figure 1.
characteristics were measured with Murata ceramic
capacitors GRM31MR71E105KA01 (1.0 mF, 25 V X7R,
1206). Larger values improve noise rejection and load
regulation transient response. Figure 23 shows the stability
region for a range of operating conditions and ESR values.
Input Decoupling (Cin)
A ceramic or tantalum 1.0 mF capacitor is recommended
and should be connected close to the NCP629 package.
Higher capacitance and lower ESR will improve the overall
line transient response.
No-Load Regulation Considerations
The NCP629 contains an overshoot clamp circuit to
improve transient response during a load current step
release. When output voltage exceeds the nominal by
approximately 20 mV, this circuit becomes active and
clamps the output from further voltage increase. Tying the
ENABLE pin to Vin will ensure that the part is active
whenever the supply voltage is present, thus guaranteeing
that the clamp circuit is active whenever leakage current is
present.
Output Decoupling (Cout)
The NCP629 is a stable component and does not require
a minimum Equivalent Series Resistance (ESR) for the
output capacitor. The minimum output decoupling value is
1.0 mF and can be augmented to fulfill stringent load
transient requirements. The regulator works with ceramic
chip capacitors as well as tantalum devices. Typical
http://onsemi.com
9
NCP629
Noise Decoupling
The power dissipated by the NCP629 can be calculated
from the following equations:
The NCP629 is a low noise regulator and needs no
external noise reduction capacitor. Unlike other low noise
regulators which require an external capacitor and have slow
startup times, the NCP629 operates without a noise
reduction capacitor, has a typical 15 ms startup delay and
achieves a 50 mVrms overall noise level between 10 Hz and
100 kHz.
P D [ V inǒI GND@I outǓ ) I outǒV in * V outǓ
(eq. 2)
or
Vin(MAX) [
PD(MAX) ) (Vout Iout)
Iout ) IGND
(eq. 3)
Enable Operation
RthJA, THERMAL RESISTANCE JUNCTION-TO-AMBIENT (°C/W)
The enable pin will turn the regulator on or off. The
threshold limits are covered in the electrical characteristics
table in this data sheet. The turn-on/turn-off transient
voltage being supplied to the enable pin should exceed a
slew rate of 10 mV/ms to ensure correct operation. If the
enable function is not to be used then the pin should be
connected to Vin.
Thermal
As power in the NCP629 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material, and the ambient temperature
affect the rate of junction temperature rise for the part. When
the NCP629 has good thermal conductivity through the
PCB, the junction temperature will be relatively low with
high power applications. The maximum dissipation the
NCP629 can handle is given by:
PD(MAX) +
TJ(MAX) * TA
RqJA
(eq. 1)
Since TJ is not recommended to exceed 125_C, then the
NCP629 soldered on 645 mm2, 1 oz copper area, FR4 can
dissipate up to 360 mW when the ambient temperature (TA)
is 25_C. See Figure 26 for RthJA versus PCB area.
340
320
300
(1 oz)
280
260
(2 oz)
240
220
200
0
100
200
300
400
500
PCB COPPER AREA (mm2)
600
700
Figure 26. RthJA vs. PCB Copper Area
Hints
Vin and GND printed circuit board traces should be as
wide as possible. When the impedance of these traces is
high, there is a chance to pick up noise or cause the regulator
to malfunction. Place external components, especially the
output capacitor, as close as possible to the NCP629, and
make traces as short as possible.
DEVICE ORDERING INFORMATION
Device
Version
Marking Code
NCP629FC15T2G
1.5 V
AAA
NCP629FC18T2G
1.8 V
AAC
NCP629FC28T2G
2.8 V
AAD
NCP629FC30T2G
3.0 V
AAE
NCP629FC33T2G
3.3 V
AAF
NCP629FC35T2G
3.5 V
AAG
NCP629FC50T2G
5.0 V
AAH
Package
Shipping†
5 Pin Flip-Chip
3000/Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
10
NCP629
PACKAGE DIMENSIONS
5 PIN FLIP-CHIP
CASE 499AY-01
ISSUE O
E
4X
A
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. COPLANARITY APPLIES TO SPHERICAL
CROWNS OF SOLDER BALLS.
B
0.10 C
È
È
TERMINAL A1
LOCATOR
D
DIM
A
A1
A2
b
D
E
e1
e2
A1
0.10 C
A2
0.05 C
A
C
MILLIMETERS
MIN
NOM MAX
0.475 0.530 0.585
0.170 0.200 0.230
0.305 0.330 0.355
0.220 0.250 0.270
1.028 BSC
1.190 BSC
0.250 BSC
0.410 BSC
SOLDERING FOOTPRINT*
SEATING
PLANE
0.82
e2
0.41
1
5X
b
0.05 C A B
0.05 C
2
0.50
3
0.25
e1
A
B
C
5X
0.25
DIMENSIONS: MILLIMETERS
*For additional information on our Pb-Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada
Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800-282-9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81-3-5773-3850
http://onsemi.com
11
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP629/D
Similar pages