Allegro A1302KUA Continuous-time ratiometric linear hall effect sensor Datasheet

A1301 and A1302
Continuous-Time Ratiometric Linear Hall Effect Sensor ICs
Features and Benefits
Description
▪
▪
▪
▪
▪
▪
The A1301 and A1302 are continuous-time, ratiometric, linear
Hall-effect sensor ICs. They are optimized to accurately provide
a voltage output that is proportional to an applied magnetic
field. These devices have a quiescent output voltage that is
50% of the supply voltage. Two output sensitivity options
are provided: 2.5 mV/G typical for the A1301, and 1.3 mV/G
typical for the A1302.
Low-noise output
Fast power-on time
Ratiometric rail-to-rail output
4.5 to 6.0 V operation
Solid-state reliability
Factory-programmed at end-of-line for optimum
performance
▪ Robust ESD performance
The Hall-effect integrated circuit included in each device
includes a Hall circuit, a linear amplifier, and a CMOS Class A
output structure. Integrating the Hall circuit and the amplifier
on a single chip minimizes many of the problems normally
associated with low voltage level analog signals.
Packages: 3 pin SOT23W (suffix LH), and
3 pin SIP (suffix UA)
High precision in output levels is obtained by internal gain
and offset trim adjustments made at end-of-line during the
manufacturing process.
These features make the A1301 and A1302 ideal for use in
position sensing systems, for both linear target motion and
rotational target motion. They are well-suited for industrial
applications over extended temperature ranges, from –40°C
to 125°C.
Two device package types are available: LH, a 3-pin SOT23W
type for surface mount, and UA, a 3-pin ultramini SIP for
through-hole mount. They are lead (Pb) free (suffix, –T) with
100% matte tin plated leadframes.
Not to scale
Functional Block Diagram
V+
To all subcircuits
Amp
Gain
Filter
VCC
Out
Offset
CBYPASS
Trim
Control
GND
A1301-DS, Rev. 17
VOUT
Continuous-Time Ratiometric
Linear Hall Effect Sensor ICs
A1301 and
A1302
Selection Guide
Part Number
Packing*
Package
Ambient, TA
SIP
–40ºC to 85ºC
A1301EUA-T
Bulk, 500 pieces/bag
A1301KLHLT-T
7-in. tape and reel, 3000 pieces/reel
A1301KUA-T
Bulk, 500 pieces/bag
A1302ELHLT-T
7-in. tape and reel, 3000 pieces/reel
Surface Mount
A1302KLHLT-T
7-in. tape and reel, 3000 pieces/reel
Surface Mount
A1302KUA-T
Bulk, 500 pieces/bag
Surface Mount
SIP
SIP
Sensitivity (Typical)
2.5 mV/G
–40ºC to 125ºC
–40ºC to 85ºC
1.3 mV/G
–40ºC to 125ºC
*Contact Allegro for additional packing options.
Absolute Maximum Ratings
Characteristic
Symbol
Notes
Rating
Units
Supply Voltage
VCC
8
V
Output Voltage
VOUT
8
V
Reverse Supply Voltage
VRCC
–0.1
V
Reverse Output Voltage
VROUT
–0.1
V
Output Sink Current
IOUT
10
mA
Range E
–40 to 85
ºC
Range K
Operating Ambient Temperature
TA
–40 to 125
ºC
Maximum Junction Temperature
TJ(max)
165
ºC
Tstg
–65 to 170
ºC
Storage Temperature
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
2
Continuous-Time Ratiometric
Linear Hall Effect Sensor ICs
A1301 and
A1302
Pin-out Drawings
Package UA
Package LH
3
1
2
1
2
3
Terminal List
Symbol
VCC
VOUT
GND
Number
Package LH
Package UA
1
1
2
3
3
2
Description
Connects power supply to chip
Output from circuit
Ground
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
3
A1301 and
A1302
Continuous-Time Ratiometric
Linear Hall Effect Sensor ICs
DEVICE CHARACTERISTICS over operating temperature range, TA, and VCC = 5 V, unless otherwise noted
Characteristic
Symbol
Test Conditions
Min.
Electrical Characteristics
Running, TJ < 165°C
4.5
Supply Voltage
VCC
Supply Current
ICC
Output open
–
VOUT(High) ISOURCE = –1 mA, Sens = nominal
4.65
Output Voltage
–
VOUT(Low) ISINK = 1 mA, Sens = nominal
Output Bandwidth
BW
–
VCC(min) to 0.95 VOUT; B = ±1400 G;
Power-On Time
tPO
–
Slew rate = 4.5 V/μs to 4.5 V/100 ns
Output Resistance
ROUT
ISINK ≤ 1 mA, ISOURCE ≥ –1 mA
–
External output low pass filter ≤ 10 kHz;
Wide Band Output Noise, rms
VOUTN
–
Sens = nominal
Ratiometry
Quiescent Output Voltage Error
ΔVOUTQ(V) TA = 25°C
–
with respect to ∆VCC1
Magnetic Sensitivity Error with
ΔSens(V) TA = 25°C
–
respect to ∆VCC2
Output
Linearity
Lin
TA = 25°C
–
–
Symmetry
Sym
TA = 25°C
Magnetic Characteristics
Quiescent Output Voltage
VOUTQ
B = 0 G; TA = 25°C
2.4
Quiescent Output Voltage over
VOUTQ(TA) B = 0 G
2.2
Operating Temperature Range
A1301; TA = 25°C
2.0
Magnetic Sensitivity
Sens
A1302; TA = 25°C
1.0
A1301
1.8
Magnetic Sensitivity over
Sens(TA)
Operating Temperature Range
A1302
0.85
1Refer to equation (4) in Ratiometric section on page 4.
2Refer to equation (5) in Ratiometric section on page 4.
Typ.
Max.
Units
–
–
4.7
0.2
20
6
11
–
0.25
–
V
mA
V
V
kHz
3
5
μs
2
5
Ω
150
–
μV
–
±3.0
%
–
±3.0
%
–
–
±2.5
±3.0
%
%
2.5
2.6
V
–
2.8
V
2.5
1.3
–
–
3.0
1.6
3.2
1.75
mV/G
mV/G
mV/G
mV/G
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
4
Continuous-Time Ratiometric
Linear Hall Effect Sensor ICs
A1301 and
A1302
Characteristic Definitions
Quiescent Output Voltage. In the quiescent state (no significant magnetic field: B = 0), the output, VOUTQ, equals one
half of the supply voltage, VCC, throughout the entire operating
ranges of VCC and ambient temperature, TA. Due to internal
component tolerances and thermal considerations, there is a
tolerance on the quiescent output voltage, ∆VOUTQ, which is
a function of both ∆VCC and ∆TA. For purposes of specification, the quiescent output voltage as a function of temperature,
∆VOUTQ(∆TA), is defined as:
ΔVOUTQ(ΔΤΑ) =
VOUTQ(ΤΑ) – VOUTQ(25ºC)
Sensitivity. The presence of a south-polarity (+B) magnetic
field, perpendicular to the branded face of the device package,
increases the output voltage, VOUT, in proportion to the magnetic
field applied, from VOUTQ toward the VCC rail. Conversely, the
application of a north polarity (–B) magnetic field, in the same
orientation, proportionally decreases the output voltage from its
quiescent value. This proportionality is specified as the magnetic
sensitivity of the device and is defined as:
2B
Sens(ΤΑ) – Sens(25ºC)
Sens(25ºC)
ΔSens(ΔV) =
Lin+ =
Lin– =
× 100%
VOUTQ(VCC)
VCC
VOUTQ(5V)
× 100%
5V
(4)
(3)
Sens(VCC)
VCC
Sens(5V)
5V
× 100%
(5)
Linearity and Symmetry. The on-chip output stage is
designed to provide linear output at a supply voltage of 5 V.
Although the application of very high magnetic fields does not
damage these devices, it does force their output into a nonlinear
region. Linearity in percent is measured and defined as:
(2)
The stability of the device magnetic sensitivity as a function of
ambient temperature, ∆ Sens (∆TA) (%) is defined as:
ΔSens(ΔΤΑ) =
ΔVOUTQ(ΔV) =
and the ratiometric change (%) in sensitivity is defined as:
Sens(25ºC)
VOUT(–B) – VOUT(+B)
The ratiometric change (%) in the quiescent voltage output is
defined as:
(1)
where Sens is in mV/G, and the result is the device equivalent
accuracy, in gauss (G), applicable over the entire operating temperature range.
Sens =
Ratiometric. The A1301 and A1302 feature a ratiometric
output. This means that the quiescent voltage output, VOUTQ,
and the magnetic sensitivity, Sens, are proportional to the supply
voltage, VCC.
VOUT(+B) – VOUTQ
2 (VOUT(+B½) – VVOUTQ )
VOUT(–B) – VOUTQ
2(VOUT(–B½) – VOUTQ)
× 100%
× 100%
(6)
(7)
and output symmetry as:
Sym =
VOUT(+B) – VOUTQ
VOUTQ – VOUT(–B)
× 100%
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
(8)
5
Continuous-Time Ratiometric
Linear Hall Effect Sensor ICs
A1301 and
A1302
Typical Characteristics
(30 pieces, 3 fabrication lots)
1301 Device Sensitivity vs. Ambient Temperature
1302 Device Sensitivity vs. Temperature
1.40
2.65
1.38
UA Package
Sensitivity (mV/G)
Sensitivity (mV/G)
2.60
2.55
2.50
LH Package
2.45
2.40
UA Package
1.36
1.34
1.32
1.30
LH Package
1.28
1.26
2.35
–50 –25
1.24
0
25
50
75
Temperature (°C)
100 125 150
-50
1301 Device VOUTQ vs. Ambient Temperature
25
50
75 100 125 150
Temperature (°C)
2.60
Output Voltage (V)
Output Voltage (V)
0
1302 Device VOUTQ vs. Ambient Temperature
2.60
2.55
2.50
2.45
2.40
–50
-25
–25
0
25
50
75 100
Temperature (°C)
125
2.55
2.50
2.45
2.40
–50
150
1301 Device Sensitivity vs. Supply Voltage
–25
0
25
50
75 100
Temperature (°C)
125
150
1302 Device Sensitivity vs. Supply Voltage
1.7
3.5
Sensitivity (mV/G)
Sensitivity (mV/G)
1.6
3.0
2.5
2.0
1.5
1.4
1.3
1.2
1.1
1.5
4.5
5.0
5.5
Supply Voltage (V)
6.0
1.0
4.5
5.0
5.5
Supply Voltage (V)
6.0
Continued on the next page...
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
6
Continuous-Time Ratiometric
Linear Hall Effect Sensor ICs
A1301 and
A1302
Typical Characteristics, continued
(30 pieces, 3 fabrication lots)
1302 Device VOUTQ vs. Supply Voltage
1301 Device VOUTQ vs. Supply Voltage
3.5
Output Voltage (V)
Output Voltage (V)
3.5
3.0
2.5
2.0
1.5
4.5
5.0
5.5
Supply Voltage (V)
3.0
2.5
2.0
1.5
4.5
6.0
5.0
5.5
Supply Voltage (V)
1302 Device LIN+ and LIN– vs. Supply Voltage
1301 Device LIN+ and LIN– vs. Supply Voltage
100.4
100.0
100.3
99.9
LIN–
Linearity (%)
100.2
Linearity (%)
6.0
100.1
100.0
LIN+
LIN+
99.8
LIN–
99.7
99.9
99.8
4.5
5.0
5.5
Supply Voltage (V)
99.6
4.5
6.0
100.0
100.5
99.9
99.8
100.4
100.3
99.7
99.6
100.2
100.1
Symmetry (%)
Symmetry (%)
6.0
1302 Device Symmetry vs. Supply Voltage
1301 Device Symmetry vs. Supply Voltage
99.5
99.4
99.3
99.2
99.1
99.0
4.5
5.0
5.5
Supply Voltage (V)
100.0
99.9
99.8
99.7
99.6
5.0
5.5
Supply Voltage (V)
6.0
99.5
4.5
5.0
5.5
Supply Voltage (V)
6.0
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
7
Continuous-Time Ratiometric
Linear Hall Effect Sensor ICs
A1301 and
A1302
Package LH, 3-Pin; (SOT-23W)
+0.12
2.98 –0.08
1.49 D
4°±4°
3
A
+0.020
0.180–0.053
0.96 D
+0.10
2.90 –0.20
+0.19
1.91 –0.06
2.40
0.70
D
0.25 MIN
1.00
2
1
0.55 REF
0.25 BSC
0.95
Seating Plane
Gauge Plane
8X 10° REF
B
PCB Layout Reference View
Branded Face
1.00 ±0.13
+0.10
0.05 –0.05
0.95 BSC
0.40 ±0.10
For Reference Only; not for tooling use (reference dwg. 802840)
Dimensions in millimeters
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
A
Active Area Depth, 0.28 mm REF
B
Reference land pattern layout
All pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary
to meet application process requirements and PCB layout tolerances
C
Branding scale and appearance at supplier discretion
D
Hall element, not to scale
NNT
1
C
Standard Branding Reference View
N = Last two digits of device part number
T = Temperature code
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
8
Continuous-Time Ratiometric
Linear Hall Effect Sensor ICs
A1301 and
A1302
Package UA, 3-Pin SIP
Matrix Leadframe
+0.08
4.09 –0.05
45°
B
C
E
2.04
1.52 ±0.05
1.44 E
+0.08
3.02 –0.05
Mold Ejector
Pin Indent
2X10°
E
Branded
Face
45°
1
D Standard Branding Reference View
A
1.02
MAX
0.51
REF
= Supplier emblem
N = Last two digits of device part number
T = Temperature code
0.79 REF
1
2
3
+0.03
0.41 –0.06
14.99 ±0.25
+0.05
0.43 –0.07
NNT
For Reference Only; not for tooling use (reference DWG-9013)
Dimensions in millimeters
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
A
Dambar removal protrusion (6X)
B
Gate and tie bar burr area
C
Active Area Depth, 0.50 mm REF
D
Branding scale and appearance at supplier discretion
E
Hall element, not to scale
1.27 NOM
Please note that there are changes to the existing UA package drawing pending.
Please contact the Allegro Marketing department for additional information.
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
9
Continuous-Time Ratiometric
Linear Hall Effect Sensor ICs
A1301 and
A1302
Package UA, 3-Pin SIP
Conventional Leadframe
+0.08
4.09 –0.05
45°
B
C
E
2.04
1.52 ±0.05
1.44 E
Mold Ejector
Pin Indent
+0.08
3.02 –0.05
E
Branded
Face
45°
1
2.16
MAX
D Standard Branding Reference View
= Supplier emblem
N = Last two digits of device part number
T = Temperature code
0.79 REF
A
0.51
REF
NNT
1
2
3
+0.03
0.41 –0.06
15.75 ±0.51
For Reference Only; not for tooling use (reference DWG-9049)
Dimensions in millimeters
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
A
Dambar removal protrusion (6X)
B Gate burr area
C Active Area Depth, 0.50 mm REF
+0.05
0.43 –0.07
D
Branding scale and appearance at supplier discretion
E
Hall element, not to scale
1.27 NOM
Copyright ©2005-2010, Allegro MicroSystems, Inc.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the
information being relied upon is current.
Allegro’s products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the
failure of that life support device or system, or to affect the safety or effectiveness of that device or system.
The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
For the latest version of this document, visit our website:
www.allegromicro.com
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
10