4.0x4.0mm RIGHT ANGLE SURFACE MOUNT LED LAMP Part Number: AA4040ZGCKT Green ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z Single color. z The Green source color devices are made with InGaN z Suitable for all SMD assembly and solder process. on Sapphire Light Emitting Diode. z Electrostatic discharge and power surge could damage z Available on tape and reel. the LEDs. z Ideal for backlighting. z It is recommended to use a wrist band or anti- z Package : 500pcs / reel. z Moisture sensitivity level : level 3. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be z RoHS compliant. electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAO6996 REV NO: V.1B DATE: FEB/25/2016 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1201009155 Selection Guide Part No. Emitting Color (Material) AA4040ZGCKT Green (InGaN) Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 2θ1/2 500 800 120° Water Clear Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. 3. Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 515 nm IF=20mA Green 525 nm IF=20mA Spectral Line Half-width Green 35 nm IF=20mA C Capacitance Green 45 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 3.3 4.1 V IF=20mA IR Reverse Current Green 50 uA VR=5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units 102.5 mW DC Forward Current 25 mA Peak Forward Current [1] 150 mA 5 V 450 V Power dissipation Reverse Voltage Electrostatic Discharge Threshold (HBM) Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAO6996 REV NO: V.1B DATE: FEB/25/2016 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1201009155 Green AA4040ZGCKT SPEC NO: DSAO6996 REV NO: V.1B DATE: FEB/25/2016 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1201009155 AA4040ZGCKT Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAO6996 REV NO: V.1B DATE: FEB/25/2016 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1201009155 PACKING & LABEL SPECIFICATIONS AA4040ZGCKT Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAO6996 REV NO: V.1B DATE: FEB/25/2016 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1201009155