BYM10-50 THRU BYM10-1000 GL41A THRU GL41Y SURFACE MOUNT GLASS PASSIVATED JUNCTION RECTIFIER * Reverse Voltage - 50 to 1600 Volts FEATURES D DO213AB ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ For surface mount applications ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ High temperature soldering guaranteed: 450°C/5 seconds at terminals. Complete device submersible temperature of 265°C for 10 seconds in solder bath E T N E P A T Forward Current - 1.0 Ampere SOLDERABLE ENDS 1st BAND 2nd BAND D1= 0.105 0.095 (2.67) (2.41) D2 0.022 (0.56) 0.018 (0.46) 0 D2 = D1 + - 0.008 (0.20) 0.205 (5.2) 0.185(4.7) 1st band denotes type and positive end (cathode) MECHANICAL DATA 2nd band denotes voltage type Dimensions in inches and (millimeters) *Glass-plastic encapsulation technique is covered by Patent No. 3,996,602 and brazed-end cap assembly by Patent No. 3,930,306 Case: JEDEC DO-213AB molded plastic over glass body Terminals: Plated terminals, solderable per MIL-STD-750, Method 2026 Polarity: Two bands indicate cathode-end -1st band denotes device type and 2nd band denotes repetitive peak reverse voltage rating Mounting Position: Any Weight: 0.0046 ounce, 0.116 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. BYM10 SYMBOLS Standard recovery device: 1st band is white Polarity color bands (2nd Band) BYM10 -50 -100 -200 -400 -600 GL41A GL41B GL41D GL41G GL41J Gray Red Orange Yellow Green 100 200 400 -800 -1000 GL41K GL41M GL41T UNITS GL41Y Blue Violet White Brown 600 800 1000 1300 1600 Volts Maximum repetitive peak reverse voltage VRRM 50 Maximum RMS voltage VRMS 35 70 140 280 420 560 700 910 1120 Volts VDC 50 100 200 400 600 800 1000 1300 1600 Volts Maximum DC blocking voltage Maximum average forward rectified current I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30.0 Amps Maximum instantaneous forward voltage at 1.0A VF (SEE FIG. 1) Maximum DC reverse current at rated DC blocking voltage Maximum full load reverse current full cycle average at TA=75°C Typical junction capacitance (NOTE 1) Typical thermal resistance (NOTE 2) (NOTE 3) TA=25°C TA=125°C 1.1 1.2 Volts IR 10.0 50.0 µA IR(AV) 30.0 µA CJ 8.0 pF RΘJA RΘJT 75.0 30.0 °C/W -65 to +175 °C Operating junction and storage temperature range TJ, TSTG NOTES: (1) Measured at 1.0 MHZ and applied reverse voltage of 4.0 VDC (2) Thermal resistance from junction to ambient, 0.24 x 0.24” (6.0 x 6.0mm) copper pads to each terminal (3) Thermal resistance from junction to terminal, 0.24 x 0.24” (6.0 x 6.0mm) copper pads to each terminal RATINGS AND CHARACTERISTIC CURVES BYM10-50 THRU BYM10-600 / GL41A THRU GL41Y FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 1.0 GL41A THRU GL41M 60 HZ RESISTIVE OR INDUCTIVE LOAD 0.75 0.5 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE GL41T THRU GL41Y 0.25 0 25 50 75 100 125 150 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 25 GL41A - M 20 15 10 5.0 0 175 1 TERMINAL TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 10 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 NUMBER OF CYCLES AT 60 HZ GL41K-Y TJ=25°C 1 PULSE WIDTH=300µs 1% DUTY CYCLE GL41A-J 0.1 TJ=100°C 1 0.1 TJ=25°C 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE JUNCTION CAPACITANCE, pF 30 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 1 1 10 REVERSE VOLTAGE, VOLTS 100 TRANSIENT THERMAL IMPEDANCE (°C/W) FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 MOUNTED ON 0.20 x 0.27” (5 x 7mm) COPPER PAD AREAS 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec 10 100