3Northway Lane North Latham,New York 12110. Tollfree:1.800.984.5337 Phone:1.518.956.2980 Fax:1.518.785.4725 Http://www.marktechopto.com SPECIFICATION PART NO. : MTSM0302AZ-HR-A 1.8mm AXIAL LED LAMP MTSM0302AZ-HR-A 1.8mm AXIAL LED LAMP Package Dimensions 0.15 1.5 2.8 R0 1.925 1.4 .8 3 4° 0.875 3.05 4.3 2.0 0.5 0.4 2.5 1.8 5.8 K A Notes: 1. All dimensions are in mm. 2. Tolerance is ±0.25mm unless otherwise noted. Description LED Chip Part No. MTSM0302AZ-HR-A Material AlGaInP/GaAs Emitting Color Deep Red VER.: 01 Lens Color Water Clear Date: 2007/10/04 Page: 1/6 MTSM0302AZ-HR-A 1.8mm AXIAL LED LAMP Absolute Maximum Ratings at Ta=25℃ Parameter Symbol Rating Unit Power Dissipation PD 72 mW Reverse Voltage VR 5 V D.C. Forward Current If 30 mA If(Peak) 100 mA Operating Temperature Range Topr. -40 to +100 ℃ Storage Temperature Range Tstg. -40 to +100 ℃ Soldering Temperature Tsld. Peak Current(1/10Duty Cycle,0.1ms Pulse Width.) Reflow Soldering: 260℃ for 10 sec. Electrical and Optical Characteristics: Parameter Symbol Condition Min. Typ. Luminous Intensity IV If=20mA 622 1050 Forward Voltage Vf If=20mA 1.9 Peak Wavelength λp If=20mA 650 nm Dominant Wavelength λd If=20mA 639 nm Reverse Current Ir Vr=5V Viewing Angle 2θ1/2 If=20mA 36 deg ∆λ If=20mA 20 nm Spectrum Line Halfwidth Max. Unit mcd 2.4 100 V µA Notes: 1.The datas tested by IS tester. 2. Customer’s special requirements are also welcome. VER.: 01 Date: 2007/10/04 Page: 2/6 MTSM0302AZ-HR-A 1.8mm AXIAL LED LAMP Typical Electrical/Optical Characteristic Curves (25℃ Ambient Temperature Unless Otherwise Noted) Relative Luminous Intensity(mcd0 Forward Current IF(mA) 50 40 30 20 10 1.6 1.8 2.0 2.2 2.4 1500 1200 900 600 300 0 2.6 10.0 0.0 Applied Voltage (V) 20.0 30.0 Forward Current (mA) Forward Current VS. Applied Voltage Forward Current VS. Luminous Intensity 50 0° 20° 10° Forward Current IF(mA) 30° 40 30 40° 1.0 0.9 0.8 20 10 0 20 40 60 80 Ambient Temperature Ta (℃) 100 50° 60° 70° 80° 90° 0.7 0.5 Ambient Temperature VS. Forward Current 0.3 0.1 0.2 0.4 0.6 Radiation Diagram VER.: 01 Date: 2007/10/04 Page: 3/6 MTSM0302AZ-HR-A 1.8mm AXIAL LED LAMP PRECAUTION IN USE Storage Recommended storage environment Temperature: 5oC ~ 30oC (41oF ~ 86oF) Humidity: 60% RH Max. Use within 7 days after opening of sealed vapor/ESD barrier bags. If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. Fold the opened bag firmly and keep in dry environment. Soldering Reflow Soldering Lead Solder 120~150℃ Pre-heat Pre-heat time 120sec. Max. 240℃ Max. Peak temperature Soldering time 10sec. Max. Condition refer to Temperatureprofile 1 *After reflow soldering rapid cooling should be avoided. Lead – free Solder 180~200℃ 120sec. Max. 260℃ Max. 10sec. Max. refer to Temperatureprofile 2 [Temperature-profile (Surface of circuit board)] Use the conditions shown to the under figure. ＜1 : Lead Solder＞ 240°C Max. 10sec. Max. 2.5~5°C/sec. Pre-heating 120~150°C 120sec. Max. 2.5~5°C/sec. ＜2 : Lead-free Solder＞ 60sec. Max. 260°C Max. 10sec. Max. 1~5°C/sec. Pre-heating 180~200°C 120sec. Max. 60sec. Max. 1~5°C/sec. VER.: 01 Date: 2007/10/04 Page: 4/6 MTSM0302AZ-HR-A 1.8mm AXIAL LED LAMP Dimensions for Tape 2.0 4.0 1.55 5° MAX 12.0 11 ° MAX 2.16 0.15 5.5 1.75 0.3 1.65 3.05 4.0 60.0±0.5 57 178.0±1 Dimensions for Reel 13.2±0.5 16.2±0.5 Notes: 1.All dimensions are in mm, tolerance is±2.0mm unless otherwise noted. 2.Specifications are subject to change without notice. VER.: 01 Date: 2007/10/04 Page: 5/6 MTSM0302AZ-HR-A 1.8mm AXIAL LED LAMP Packing REEL QUANTITY: 1,500 PCS Marktech Optoelectronics. PART NO :MTXXXX-XX 178±1 Q'TY : PCS LOT NO :XXXXXXXXX DATE : BIN CODE: Marktech Optoelectronics. PART NO :MTXXXX-XX Q'TY : PCS LOT NO :XXXXXXXXX DATE : BIN CODE: 溼氣敏感材料 MOISTURE SENSITIVE DEVICES 1. 在5°C~30°C密封貯藏， 1年有效。 Shelf life in sealed bag : 12 months at 5°C~30°C . 2. 開封後需在168小時內使用。 moun this bag ted withi n is open ed . Marktech Optoel ectronics. PART NO :MTXXXX-XX Q'TY : PCS LOT NO :XXXXXXXX X DATE : BIN CODE: s after MOISTU 溼氣敏感 Marktech Optoelectronics. PART NO :MTXXXX-XX RE SEN 材料 1. |b5°C SITIVE ~30° C±K Shelf ?E?J DEV life at 5°C~ in seale AA!A2|~|3RA ICES d bag 30°C 2. ?}?E : 24 mont !C ?a?Y . hs Devices |b72 ?pRE ?o‥ I￥I!C 72 hour have to be BAG QUANTITY: 1,500 PCS 230± 1.0 Devices have to be mounted within 168 hours after this bag is opened . 270±1.0 Q'TY : PCS LOT NO :XXXXXXXXX DATE : BIN CODE: INSIDE BOX QUANTITY: 4 BAGS TOTAL: 6,000 PCS 27 5± 2 23 5± 75±2 Marktech Optoelectronics. PART NO :MTXXXX-XX 2 Q'TY : PCS LOT NO :XXXXXXXXX DATE : BIN CODE: Notes: 1. All dimensions are in mm, tolerance is±2.0mm unless otherwise noted. 2. Specifications are subject to change without notice. VER.: 01 Date: 2007/10/04 Page: 6/6