DS90LV017A www.ti.com SNLS022C – MARCH 2000 – REVISED APRIL 2013 DS90LV017A LVDS Single High Speed Differential Driver Check for Samples: DS90LV017A FEATURES DESCRIPTION • • • • • • • • • • The DS90LV017A is a single LVDS driver device optimized for high data rate and low power applications. The DS90LV017A is a current mode driver allowing power dissipation to remain low even at high frequency. In addition, the short circuit fault current is also minimized. The device is designed to support data rates in excess of 600Mbps (300MHz) utilizing Low Voltage Differential Signaling (LVDS) technology. 1 2 • • • >600 Mbps (300 MHz) Switching Rates 0.3 ns Typical Differential Skew 0.7 ns Maximum Differential Skew 1.5 ns Maximum Propagation Delay 3.3V Power Supply Design ±355 mV Differential Signaling Low Power Dissipation (23 mW @ 3.3V Static) Flow-Through Design Simplifies PCB Layout Interoperable with Existing 5V LVDS Devices Power Off Protection (Outputs in High Impedance) Conforms to TIA/EIA-644 Standard 8-Lead SOIC Package Saves Space Industrial Temperature Operating Range – (−40°C to +85°C) The device is in a 8-lead SOIC package. The DS90LV017A has a flow-through design for easy PCB layout. The differential driver outputs provides low EMI with its typical low output swing of 355 mV. The DS90LV017A can be paired with its companion single line receiver, the DS90LV018A, or with any of TI's LVDS receivers, to provide a high-speed point-topoint LVDS interface. Connection Diagram Figure 1. Dual-In-Line See Package Number D (R-PDSO-G8) Functional Diagram These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2000–2013, Texas Instruments Incorporated DS90LV017A SNLS022C – MARCH 2000 – REVISED APRIL 2013 www.ti.com Absolute Maximum Ratings (1) −0.3V to +4V Supply Voltage (VCC) −0.3V to +3.6V Input Voltage (DI) −0.3V to +3.9V Output Voltage (DO±) Maximum Package Power Dissipation @ +25°C D Package 1190 mW Derate D Package 9.5 mW/°C above +25°C −65°C to +150°C Storage Temperature Range Lead Temperature Range Soldering (4 sec.) +260°C ≥ 8kV (HBM 1.5 kΩ, 100 pF) ESD Ratings (EIAJ 0 Ω, 200 pF) ≥ 1000V (CDM) ≥ 1000V (IEC direct 330 Ω, 150 pF) (1) ≥ 4kV “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be ensured. They are not meant to imply that the devices should be operated at these limits. Electrical Characteristics specifies conditions of device operation. Recommended Operating Conditions Min Typ Max Units Supply Voltage (VCC) 3.0 3.3 3.6 V Temperature (TA) −40 25 +85 °C Electrical Characteristics Over Supply Voltage and Operating Temperature ranges, unless otherwise specified (1) (2) (3) Symbol Parameter Conditions Pin Min Typ Max Units DO+, DO− 250 355 450 mV 1 35 mV 1.4 1.6 V DIFFERENTIAL DRIVER CHARACTERISTICS VOD Output Differential Voltage ΔVOD VOD Magnitude Change RL = 100Ω (Figure 2) VOH Output High Voltage VOL Output Low Voltage VOS Offset Voltage ΔVOS Offset Magnitude Change IOXD Power-off Leakage IOSD Output Short Circuit Current VIH Input High Voltage VIL Input Low Voltage IIH Input High Current VIN = 3.3V or 2.4V IIL Input Low Current VIN = GND or 0.5V VCL Input Clamp Voltage ICL = −18 mA ICC Power Supply Current No Load (2) (3) 2 1.1 1.2 1.375 V 0 3 25 mV ±1 ±10 μA −5.7 −8 mA VCC V VOUT = VCC or GND, VCC = 0V DI 2.0 GND −1.5 VIN = VCC or GND RL = 100Ω (1) 0.9 1.125 VCC V 0.8 V ±2 ±10 μA ±1 ±10 μA −0.6 V 5 8 mA 7 10 mA Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD. All typicals are given for: VCC = +3.3V and TA = +25°C. The DS90LV017A is a current mode device and only function with datasheet specification when a resistive load is applied to the drivers outputs. Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: DS90LV017A DS90LV017A www.ti.com SNLS022C – MARCH 2000 – REVISED APRIL 2013 Switching Characteristics Over Supply Voltage and Operating Temperature Ranges, unless otherwise specified (1) (2) (3) (4) Symbol Parameter Conditions Min Typ Max Units DIFFERENTIAL DRIVER CHARACTERISTICS tPHLD Differential Propagation Delay High to Low RL = 100Ω, CL = 15 pF 0.3 0.8 1.5 ns tPLHD Differential Propagation Delay Low to High (Figure 3 and Figure 4) 0.3 1.1 1.5 ns tSKD1 Differential Pulse Skew |tPHLD − tPLHD| (5) 0 0.3 0.7 ns tSKD3 Differential Part to Part Skew (6) 0 1.0 ns tSKD4 Differential Part to Part Skew (7) 0 1.2 ns tTLH Transition Low to High Time 0.2 0.5 1.0 ns tTHL Transition High to Low Time 0.2 0.5 1.0 fMAX Maximum Operating Frequency (8) (1) (2) (3) (4) (5) (6) (7) (8) 350 ns MHz All typicals are given for: VCC = +3.3V and TA = +25°C. These parameters are ensured by design. The limits are based on statistical analysis of the device performance over PVT (process, voltage, temperature) ranges. CL includes probe and fixture capacitance. Generator waveform for all tests unless otherwise specified: f = 1 MHz, ZO = 50Ω, tr ≤ 1 ns, tf ≤ 1 ns (10%-90%). tSKD1, |tPHLD − tPLHD|, is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the same channel. tSKD3, Differential Part to Part Skew, is defined as the difference between the minimum and maximum specified differential propagation delays. This specification applies to devices at the same VCC and within 5°C of each other within the operating temperature range. tSKD4, part to part skew, is the differential channel to channel skew of any event between devices. This specification applies to devices over recommended operating temperature and voltage ranges, and across process distribution. tSKD4 is defined as |Max − Min| differential propagation delay. fMAX generator input conditions: tr = tf < 1 ns (0% to 100%), 50% duty cycle, 0V to 3V. Output criteria: duty cycle = 45%/55%, VOD > 250mV. Parameter Measurement Information Figure 2. Differential Driver DC Test Circuit Figure 3. Differential Driver Propagation Delay and Transition Time Test Circuit Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: DS90LV017A 3 DS90LV017A SNLS022C – MARCH 2000 – REVISED APRIL 2013 www.ti.com Parameter Measurement Information (continued) Figure 4. Differential Driver Propagation Delay and Transition Time Waveforms APPLICATION INFORMATION Table 1. Device Pin Descriptions Pin # 4 Name Description 2 DI1 TTL/CMOS driver input pins 7 DO1+ Non-inverting driver output pin 8 DO1− Inverting driver output pin 4 GND Ground pin 1 VCC Positive power supply pin, +3.3V ± 0.3V 3, 5, 6 NC No connect Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: DS90LV017A DS90LV017A www.ti.com SNLS022C – MARCH 2000 – REVISED APRIL 2013 Typical Performance Curves Output High Voltage vs Power Supply Voltage Output Low Voltage vs Power Supply Voltage Figure 5. Figure 6. Output Short Circuit Current vs Power Supply Voltage Differential Output Voltage vs Power Supply Voltage Figure 7. Figure 8. Differential Output Voltage vs Load Resistor Offset Voltage vs Power Supply Voltage Figure 9. Figure 10. Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: DS90LV017A 5 DS90LV017A SNLS022C – MARCH 2000 – REVISED APRIL 2013 www.ti.com Typical Performance Curves (continued) 6 Power Supply Current vs Frequency Power Supply Current vs Power Supply Voltage Figure 11. Figure 12. Power Supply Current vs Ambient Temperature Differential Propagation Delay vs Power Supply Voltage Figure 13. Figure 14. Differential Propagation Delay vs Ambient Temperature Differential Skew vs Power Supply Voltage Figure 15. Figure 16. Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: DS90LV017A DS90LV017A www.ti.com SNLS022C – MARCH 2000 – REVISED APRIL 2013 Typical Performance Curves (continued) Differential Skew vs Ambient Temperature Transition Time vs Power Supply Voltage Figure 17. Figure 18. Transition Time vs Ambient Temperature Figure 19. Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: DS90LV017A 7 DS90LV017A SNLS022C – MARCH 2000 – REVISED APRIL 2013 www.ti.com REVISION HISTORY Changes from Revision B (April 2013) to Revision C • 8 Page Changed layout of National Data Sheet to TI format ............................................................................................................ 7 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: DS90LV017A PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) DS90LV017ATM NRND SOIC D 8 95 TBD Call TI Call TI -40 to 85 LV17A TM DS90LV017ATM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) SN | CU SN Level-1-260C-UNLIM -40 to 85 LV17A TM DS90LV017ATMX NRND SOIC D 8 2500 TBD Call TI Call TI -40 to 85 LV17A TM DS90LV017ATMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) SN | CU SN Level-1-260C-UNLIM -40 to 85 LV17A TM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant DS90LV017ATMX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 DS90LV017ATMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DS90LV017ATMX SOIC D 8 2500 367.0 367.0 35.0 DS90LV017ATMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated