EDF1AM THRU EDF1DM MINIATURE GLASS PASSIVATED FAST EFFICIENT BRIDGE RECTIFIER Reverse Voltage - 50 to 200 Volts FEATURES Case Style DFM ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ This series is UL listed under Recognized Component Index, file number E54214 ♦ Glass passivated chip junctions ♦ High forward surge current capability ♦ Ideal for printed circuit boards ♦ Superfast recovery times for high efficiency ♦ High temperature soldering guaranteed: 260°C/10 seconds at 5 lbs. (2.3kg) tension 0.255 (6.5) 0.315 (8.00) 0.245 (6.2) 0.285 (7.24) 0.335 (8.51) 0.320 (8.12) 0.130 (3.3) 0.120 (3.05) Forward Current - 1.0 Ampere 0.080 (2.03) 0.050 (1.27) 0.045 (1.14) 0.035 (0.89) 0.185 (4.69) 0.150 (3.81) 0.023 (0.58) 0.018 (0.46) 0.075 (1.90) 0.055 (1.39) 0.205 (5.2) 0.195 (5.0) MECHANICAL DATA 0.013 (3.3) 0.0086 (0.22) Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on body Mounting Position: Any Weight: 0.04 ounce, 1.0 gram 0.350 (8.9) 0.300 (7.6) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS EDF1AM EDF1BM EDF1CM EDF1DM UNITS Maximum repetitive peak reverse voltage VRRM 50 100 150 200 Volts Maximum RMS voltage VRMS 35 70 106 140 Volts Maximum DC blocking voltage VDC 50 100 150 200 Volts Maximum average forward output rectified current at TA=40°C I(AV) 1.0 Amp Peak forward surge current single half sine-wave superimposed on rated load (JEDEC Method) TJ=150°C IFSM 50.0 Amps Rating for fusing (t < 8.3ms) I2t 10.0 A2sec Maximum instantaneous forward voltage drop per leg at 1.0A VF 1.05 Volts Maximum reverse current at rated DC blocking voltage IR 5.0 1.0 µA mA Maximum reverse recovery time at (NOTE 1) trr 50.0 ns Typical thermal resistance per leg (NOTE 2) RΘJA RΘJL 38.0 12.0 °C/W TJ, TSTG -55 to +150 °C TA=25°C TA=125°C Operating junction and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with 0.51 x 0.51" (13 x 13mm) copper pads 7/28/98 RATINGS AND CHARACTERISTICS CURVES EDF1AM THRU EDF1DM FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 60 1.0 60 HZ RESISTIVE OR INDUCTIVE LOAD P.C.B. MOUNTED ON 0.51 x 0.51” (13 x 13mm) COPPER PADS WITH 0.06” (1.5mm) LEAD LENGTH 0.75 0.5 CAPACITIVE LOADS Ipk / IAV=5.0 Ipk / IAV=10 Ipk / IAV=20 0.25 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES FIG. 1 - DERATING CURVES OUTPUT RECTIFIED CURRENT 50 40 30 40 60 80 100 120 140 160 1.0 CYCLE 20 10 0 0 20 SINGLE SINE-WAVE (JEDEC Method) TJ=150°C 100 10 1 NUMBER OF CYCLES AT 60Hz AMBIENT TEMPERATURE, °C FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG FIG. 3 - TYPICAL FORWARD CHARACTERISTICS PER LEG 1,000 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 15 10 5 1 10 REVERSE VOLTAGE, VOLTS TJ=25°C 0 20 0 0.1 1 0.1 FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 25 10 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 30 TJ=125°C 100 100 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 100