POWER LDO03C Series 15 Watts Data Sheet Total Power: Input Voltage: # of Outputs: 15 Watts 3 - 13.8 Vdc Single Special features 3 A output current rating Input voltage range: 3 - 13.8 Vdc Adjustable out voltage: 0.59 - 5.1 V Optional factory setting with power good Excellent transient response Electrical Specifications Power enable Input Minimum airflow Input range: Small package Input current: Minimum load Remote OFF 50 mA 5 mA Input current (max.): See Note 3 3 A @ lo max. Start-up time Power up Remote ON/OFF 3 ms 2 ms Maximum power: See Note 5 0.59 - 5.1 V Output setpoint accuracy: 0.1% trim resistors ±1.0% Line regulation: Low line to high line ±0.5% Load regulation: Full load to min. load ±0.5% Termination voltage capability RoHS compliant SAFETY UL, cUL 60950-1 TÜV Product Service (EN60950) IEC60950 3 - 13.8 Vdc Output Min./max. load: 0 A/3 A Overshoot: At turn-on 0.5% max. Undershoot: At turn-off 100 mV max. Ripple and noise 5 Hz to 20 MHz: See Note 1 25 mV Vin = 5 V, Vout = 2.5 V Transient response: See Note 1, 2 235 mV max. deviation 20 μs recovery to within regulation band Efficiency (high input): Vin = 5 V, Vo = 2.5 V, lo = 3 A 90% Switching frequency: Fixed 1.5 MHz General Material flammability: UL94V-0 Weight: 1.7 g (0.06 oz.) MTBF: 12 V @ 40 °C, 100% load Bellcore 332 10,000,000 hours Coplanarity: Surface mount models 50 μm LDO03C Series Data Sheet Environmental Specifications Thermal performance: Operating ambient -40 °C to +85 °C See Note 5 Non-operating ambient -40 °C to +125 °C Protection Hiccup, non-latching Short-circuit: IEC68-2-6 to the levels of IEC721-3-2 Hiccup, non-latching Input: See Note 6 0 μF Output: See Note 7 0 μF Overvoltage protection: Recommended System Capacitance Ordering Information Model Number (3,5) LDO03C-005W05-VJ Regulation Input Voltage Output Voltage Output Current (Min.) Output Current (Max.) Efficiency (Typical) Line Load 3 - 13.8 Vdc 0.59 - 5.1 V 0A 3A 90% ±0.2% ±0.5% LDO03C-005W05-HJ 3 - 13.8 Vdc 0.59 - 5.1 V 0A 3A 90% ±0.2% ±0.5% LDO03C-005W05-SJ 3 - 13.8 Vdc 0.59 - 5.1 V 0A 3A 90% ±0.2% ±0.5% Part Number System with Options Product Family LDO Product Family LDO = LDO Series Rated Output Current 03 Rated Output Current 03 = 3 Amp Performance Input Voltage Number of Pins Type of Output C 00 5W Performance C = Cost Optimized Input Voltage 00 = 3 - 13.8 V Type of Output 5 W = 5 Pins and Wide Output Output Voltage Mounting Option 05 Output Voltage 05 = 0.59 - 5.1 V Custom Option V X Mounting Option V = Vertical H = Horizontal S = Horizontal SMT VS = Vertical SMT Custom Option Output Voltage Adjustment of the LDO03C Series Notes: The ultra-wide output voltage trim range offers major advantages to users who select the LDO03C series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.59 - 5.1 Vdc. When the LDO03C converter leaves the factory, the output has been adjusted to the default voltage of 0.59 V. 3. External input fusing is recommended. RoHS Compliance J RoHS Compliance J = Pb free (RoHS 6/6 compliant) 1. Measured as per recommended system capacitance. See Technical Reference Note. 2. di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.50 lo to full lo and full lo to 0.50. 4. Additional part numbers may be available with different output voltages. 5. Airflow dependent, 100 LFM minimum required. 6. No capacitors needed for ripple current stability. 7. No capacitors needed for stability. 8. TSE RoHS 5/6 (non Pb-free) compliant versions may be available on special request, please consult your local sales representative for details. 9. NOTICE: Some models do not support all options. Please contact your local Artesyn Embedded Technologies representative or use the on-line model number search tool at http://www.Artesyn.com/power to find a suitable alternative. LDO03C Series Data Sheet Mechanical Drawings Vertical Mount Dimensions in inches (mm). Tolerances es (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) .370 9.40 .212 5.37 .610 15.49 .16 3.94 .051 1.30 .050 1.27 .067 1.70 TYP .025 0.64 SQ. PIN Horizontal Mount .370 9.40 .292 7.41 .131 3.33 .610 15.49 .051 1.30 .067 1.70 TYP .540 13.72 .125 3.18 .025 0.64 SQ PIN .120 3.05 .025 0.64 TYP LDO03C Series Data Sheet Mechanical Drawings Mating Connectors Horizontal Mount .370 9.40 .315 MAX [8.00 MAX] .131 3.33 .610 15.49 .540 13.72 .040 1.02 TYP .051 1.30 .067 1.70 TYP Pin Assignments Single Output 1 2 3 4 5 6 *This is a Preliminary Datasheet. Artesyn Embedded Technologies reserves the right to make changes to the information contained herein without notice and assumes no liability as a result of its use or application. Enable Vin Common/RTN Vout PG/Trim Mech Pin (Horz/SMT only) WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2014 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] LDO03C DS Rev. 07.25.14