LT1080/LT1081 Advanced Low Power 5V RS232 Dual Driver/Receiver U DESCRIPTIO FEATURES ■ ■ ■ ■ ■ ■ ■ Superior to CMOS – Improved Speed: Operates over 120kBaud – Improved Protection: Outputs Can Be Forced to ±30V without Damage – Three-State Outputs Are High Impedance When Off – Only Needs 1µF Capacitors Absolutely No Latchup CMOS Comparable Low Power: 60mW Can Power Additional RS232 Drivers: 10mA Supply Current in Shutdown: 1µA Available in SO Package Available with or without Shutdown U APPLICATIO S ■ ■ ■ ■ For applications requiring up to five drivers and five receivers with charge pump in one package see the LT1130A Series data sheet. A version of the LT1080/LT1081, the LT1180A and LT1181A that use only 0.1µF capacitors, is also available. All of Linear Technology’s RS232 ICs are available in standard surface mount packages. Portable Computers Battery-Powered RS232 Systems Power Supply Generator Terminals Modems , LTC and LT are registered trademarks of Linear Technology Corporation. U ■ The LT®1080/LT1081 are the only dual RS232 driver/ receiver with charge pump to guarantee absolutely no latchup. These interface optimized devices provide a realistic balance between CMOS levels of power dissipation and real world requirements for ruggedness. The driver outputs are fully protected against overload and can be shorted to ±30V. Unlike CMOS, the advanced architecture of the LT1080/LT1081 does not load the signal line when “shut down” or when power is off. Both the receiver and RS232 outputs are put into a high impedance state. An advanced output stage allows driving higher capacitive loads at higher speeds with exceptional ruggedness against ESD. TYPICAL APPLICATIO 17 4 3 5 LOGIC INPUTS –9V OUTPUT 1µF 6 15 11 8 13 14 RS232 OUTPUT RS232 OUTPUT RS232 INPUT 18 9 5k V + OUTPUT RL TO V – 6 2 VCC = 5V 0 –2 –4 V – OUTPUT –10 0 16 1080/81 • TA01 RL TO GND RL TO V + –8 RS232 INPUT RL TO GND 4 –6 5k 10 ON/OFF 10 8 7 12 LOGIC OUTPUTS Supply Generator Outputs 9V OUTPUT 1µF LT1080 1µF 5V INPUT OUTPUT VOLTAGE (V) 1µF 2 2 4 6 8 10 12 14 16 18 20 OUTPUT CURRENT (mA) 1080/81 TA01a 10801fe 1 LT1080/LT1081 W W W AXI U U ABSOLUTE RATI GS (Note 1) Supply Voltage (VCC) ................................................. 6V V + ........................................................................................... 12V V – ....................................................................................... –12V Input Voltage Driver ........................................................... V – to V + Receiver ................................................. –30V to 30V ON/OFF Pin .............................................. GND to 12V Output Voltage Driver ................................. (V – + 30V) to (V + – 30V) Receiver .................................. –0.3V to (VCC + 0.3V) Short-Circuit Duration V + ...................................................................................... 30 sec V – ...................................................................................... 30 sec Driver Output ............................................... Indefinite Receiver Output ........................................... Indefinite Operating Temperature Range LT1080C/LT1081C ................................. 0°C to 70°C LT1080I/LT1081I ................................ –40°C to 85°C LT1080M/LT1081M (OBSOLETE) ... –55°C to 125°C Storage Temperature Range ..................–65°C to 150°C Lead Temperature (Soldering, 10 sec)................. 300°C U W U PACKAGE/ORDER I FOR ATIO TOP VIEW NC 1 18 ON/OFF C1+ 2 17 VCC V+ 3 C1– 4 C2 + 5 14 REC1 IN C2 – 6 13 REC1 OUT ORDER PART NUMBER 16 GND LT1080 15 TR1 OUT LT1080CN LT1080CSW LT1080IN LT1080ISW ORDER PART NUMBER TOP VIEW C1+ 1 16 VCC V+ 2 15 GND C1– 3 C2 + 4 C2 – 5 12 REC1 OUT – 14 TR1 OUT LT1081 13 REC1 IN V– 7 12 TR1 IN 6 11 TR1 IN TR2 OUT 8 11 TR2 IN TR2 OUT 7 10 TR2 IN REC2 IN 9 10 REC2 OUT REC2 IN 8 9 V REC2 OUT N PACKAGE SW PACKAGE 16-LEAD PDIP 16-LEAD PLASTIC SO WIDE TJMAX = 150°C, θJA = 120°C/W, θJC = 50°C/W (N) TJMAX = 150°C, θJA = 95°C/W, θJC = 27°C/W (SW) N PACKAGE SW PACKAGE 18-LEAD PDIP 18-LEAD PLASTIC SO WIDE TJMAX = 150°C, θJA = 120°C/W, θJC = 50°C/W (N) TJMAX = 150°C, θJA = 90°C/W, θJC = 26°C/W (SW) J PACKAGE 18-LEAD CERDIP TJMAX = 150°C, θJA = 100°C/W, θJC = 40°C/W (J) LT1081CN LT1081CSW LT1081IN LT1081ISW LT1080CJ LT1080MJ J PACKAGE 16-LEAD CERDIP TJMAX = 150°C, θJA = 100°C/W, θJC = 40°C/W (J) OBSOLETE PACKAGE OBSOLETE PACKAGE Consider N Package for Alternate Source Consider N Package for Alternate Source LT1081CJ LT1081MJ Consult LTC Marketing for parts specified with wider operating temperature ranges. 10801fe 2 LT1080/LT1081 ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 2) PARAMETER CONDITIONS MIN TYP MAX UNITS ● ● 5 –5 7.3 –6.5 1.4 1.4 0.8 2 V V 5 5 20 20 µA µA Driver Output Voltage Swing Load = 3k to GND Both Outputs Positive Negative Logic Input Voltage Level Input Low Level (VOUT = High) Input High Level (VOUT = Low) ● ● Logic Input Current VIN ≥ 2V VIN ≤ 0.8V ● ● Output Short-Circuit Current Sourcing Current, VOUT = 0V Sinking Current, VOUT = 0V Output Leakage Current SHUTDOWN (Note 3), VOUT = ±30V Data Rate (Note 6) RL = 3k, CL = 2500pF RL = 3k, CL = 1000pF Slew Rate RL = 3k, CL = 51pF 9 –9 12 –12 10 ● V V mA mA 100 120 250 µA kBd kBd 4 15 0.8 0.2 1.3 1.3 30 V/µs Receiver Input Voltage Thresholds Input Low Threshold Commercial Industrial and Military ● ● Input High Threshold Commercial Industrial and Military ● ● Hysteresis ● Input Resistance VIN = ±10V Output Voltage Output Low, IOUT = –1.6mA Output High, IOUT = 160µA (VCC = 5V) Output Short-Circuit Current Sinking Current, VOUT = VCC Sourcing Current, VOUT = 0V Output Leakage Current SHUTDOWN (Note 3), 0V ≤ VOUT ≤ VCC ● ● 0.1 V V 1.7 1.7 2.4 3.0 V V 0.4 1 V kΩ 3 5 7 0.4 3.5 0.2 4.8 –10 0.6 –20 1 1 ● V V mA mA 10 µA Power Supply Generator (Note 4) V + Output Voltage IOUT = 0mA IOUT = 10mA IOUT = 15mA 8.0 7.0 6.5 9.0 8.0 7.5 V V V V – Output Voltage IOUT = 0mA IOUT = –10mA IOUT = –15mA –7.5 –5.5 –5.0 –8.5 –6.5 –6.0 V V V Supply Current ● Supply Leakage Current (VCC) SHUTDOWN (Note 3), LT1080 Only ● ON/OFF Pin Current 0V ≤ VON/OFF ≤ 5V, LT1080 Only ● Supply Rise Time (Note 5), LT1080 Only Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: These parameters apply for 4.5V ≤ VCC ≤ 5.5V and VON/OFF = 3V, unless otherwise specified. Note 3: VON/OFF = 0.4V for –55°C ≤ TA ≤ 50°C, and VON/OFF = 0.2V for 50°C ≤ TA ≤ 125°C. (LT1080 only) 12 22 mA 1 100 µA 80 µA –15 1 ms Note 4: Unless otherwise specified, VCC = 5V, external loading of V + and V – equals zero and the driver outputs are low (inputs high). Note 5: Time from either SHUTDOWN high or power on until V + ≥ 6V and V – ≤ –6V. All external capacitors are 1µF. Note 6: Data rate operation guaranteed by slew rate, short-circuit current and propagation delay tests. 10801fe 3 LT1080/LT1081 U U U PI FU CTIO S (Pin numbers refer to LT1080) C1+; C1–; C2+; C2 – (Pins 2, 4, 5, 6): Requires an external capacitor (≥1µF) from C1 + to C1 – and another from C2 + to C2 –. Pin 2 can be used for connecting a second positive supply. When a separate positive supply is used, C1 can be deleted. V + (Pin 3): Positive Supply for RS232 Drivers. V + ≈ 2VCC – 1.5V. Requires an exterenal capacitor (≥1µF) for charge storage. May be loaded (up to 15mA) for external system use. Loading does reduce V + voltage (see graphs). Capacitor may be tied to ground or +5V input supply. With multiple transceivers, the V + and V – pins may be paralleled into common capacitors. V – (Pin 7): Negative Supply for RS232 Drivers. V – ≈ –(2VCC – 2.5V). Requires an external capacitor (≥1µF) for charge stroage. May be loaded (up to –15mA) for external system use. Loading does reduce V – voltage (see graphs). With multiple transceivers, the V + and V – pins may be paralleled into common capacitors. TR2 OUT; TR1 OUT (Pins 8, 15): Driver Outputs with RS232 Voltage Levels. Outputs are in a high impedance state when in the SHUTDOWN mode or when power is off (VCC = 0V) to allow data line sharing. Outputs are fully short-circuit protected from (V – + 30V) to (V + – 30V) with power on, off or in the SHUTDOWN mode. Typical output breakdowns are greater than ±45V and higher applied voltages will not damage the device if moderately current limited. Shorting one output will affect output from the other. REC2 IN; REC1 IN (Pins 9, 14): Receiver Inputs. Accepts RS232 voltage levels (±30V) and has 0.4V of hysteresis to provide noise immunity. Input impedance is nominally 5kΩ. REC2 OUT; REC1 OUT (Pins 10, 13): Receiver Outputs with TTL/CMOS Voltage Levels. Outputs are in a high impedance state when in the SHUTDOWN mode to allow data line sharing. Outputs are fully short-circuit protected to ground or VCC with power on, off or in the SHUTDOWN mode. TR2 IN; TR1 IN (Pins 11, 12): RS232 Driver Input Pins. Inputs are TTL/CMOS compatible. Inputs should not be allowed to float. Tie unused inputs to VCC. GND (Pin 16): Ground Pin. VCC (Pin 17): Input Supply Pin. Supply current drops to zero in the SHUTDOWN mode. ON/OFF (Pin 18): Contols the operation mode of the LT1080 and is TTL/CMOS compatible. A logic low puts the device in the SHUTDOWN mode which reduces input supply current to zero and places both driver and receiver outputs in a high impedance state. A logic high fully enables the device. U W TYPICAL PERFOR A CE CHARACTERISTICS 10 VCC = 5.5V 10 OUTPUT HIGH 4 VCC = 4.5V 2 0 RL = 3k –2 –4 LOADED TO V – 6 VCC = 5V VCC = 5V VCC = 4.5V VCC = 5V –2 –4 –6 –8 –8 LOADED TO V + 1080/81 G01 LOADED TO GROUND 0 2 4 6 VCC = 5V C1 TO C4 = 1µF RL = 4.7k; V + TO V – 4 2 0 –2 –4 –6 –8 V – OUTPUT VOLTAGE –10 125 LOADED TO GROUND 2 0 V + SUPPLY 8 4 –6 VCC = 5.5V OUTPUT LOW –10 –55 –25 0 25 50 75 100 TEMPERATURE (°C) 10 V + OUTPUT VOLTAGE 8 OUTPUT VOLTAGE (V) DRIVER OUTPUT VOLTAGE (V) 8 6 Supply Generation from VCC or Shutdown Supply Generator Outputs SUPPLY VOLTAGE (V) Driver Output Voltage V – SUPPLY –10 6 8 10 12 14 16 18 20 OUTPUT CURRENT (mA) 1080/81 G02 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 TIME (ms) 1080/81 G03 10801fe 4 LT1080/LT1081 U W TYPICAL PERFOR A CE CHARACTERISTICS Receiver Output Short-Circuit Current Receiver Input Thresholds ON/OFF Pin Current vs Voltage 100 3.00 40 35 2.75 INPUT HIGH 2.00 1.75 1.50 INPUT LOW 1.25 INPUT CURRENT (µA) 2.25 30 OUTPUT SINKING OUTPUT CURRENT (mA) INPUT THRESHOLD (V) 2.50 10 OUTPUT SOURCING 1 20 15 10 5 1.00 0 0.75 –5 0.50 –55 –25 0 25 50 75 TEMPERATURE (°C) 100 0.1 –55 125 –10 –25 0 25 50 75 TEMPERATURE (°C) 100 125 0 ON/OFF Pin Thresholds 2 3 INPUT VOLTAGE (V) 4 5 1080/81 G06 Driver Output Leakage in Shutdown Supply Current in Shutdown 5.0 1 1080/81 G05 1080/81 G04 100 1000 VCC = 5V OUTPUT LEAKAGE CURRENT (µA) 4.5 4.0 SUPPLY CURRENT (nA) ON/OFF PIN VOLTAGE (V) 25 3.5 3.0 2.5 MINIMUM ON VOLTAGE 2.0 1.5 100 10 1.0 MAXIMUM OFF VOLTAGE 0.5 10 VOUT = 30V 1 VOUT = –30V 0 –55 –25 0 25 50 75 TEMPERATURE (°C) 100 125 1 –55 –25 0 25 50 75 TEMPERATURE (°C) 1080/81 G07 5V 0V –5V DRIVER 10V OUTPUT 5V HIGH 0V RECEIVER OUTPUT 5V 0V RECEIVER 0V OUTPUT –5V LOW –10 INPUT 5V 0V ON/OFF INPUT 4µs 6µs 8µs 1080/81 G10.tiff –25 0 25 50 75 TEMPERATURE (°C) 5V 0V 0 VCC = 5V RL = 3k 1ms 2ms 3ms 4ms 1080/81 G11.tiff 100 125 1080/81 G09 Shutdown to Driver Output DRIVER OUTPUT 2µs 125 1080/81 G08 Output Waveforms 0 VCC = 5V RL = 3k 100 0.1 –55 Shutdown to Receiver Output RECEIVER OUTPUT 6V 4V 2V 0V ON/OFF INPUT 5V 0V 0 VCC = 5V 1ms 2ms 3ms 4ms 1080/81 G11.tiff 10801fe 5 LT1080/LT1081 U U W U APPLICATIO S I FOR ATIO The driver output stage of the LT1080 offers significantly improved protection over older bipolar and CMOS designs. In addition to current limiting, the driver output can be externally forced to ±30V with no damage or excessive current flow, and will not disrupt the supplies. Some drivers have diodes connected between the outputs and the supplies, so externally applied voltages can cause excessive supply voltage to develop. Placing the LT1080 in the SHUTDOWN mode (Pin 18 low) puts both the driver and receiver outputs in a high impedance state. This allows data line sharing and transceiver applications. LT1080/LT1081 Driver Transceiver The SHUTDOWN mode also drops input supply current (VCC; Pin 17) to zero for power-conscious systems. LT1080 #1 DRIVER 30V –30V OUTPUT CAN BE FORCED EXTERNALLY LOGIC TRANSMIT/RECEIVE LINE 1080/81 F01 RS232 TRANSMIT/RECEIVE LINE LT1080 #2 RECEIVER Older RS232 Drivers and CMOS Drivers V+ WITH SOME DRIVERS, EXTERNALLY APPLIED VOLTAGE CAN FORCE THE SUPPLIES V– ON/OFF (TRANSMIT/ RECEIVE) INPUT 1080/81 F03 1080/81 F02 Sharing a Receiver Line Sharing a Transmitter Line LT1080 #1 RECEIVER LT1080 #1 DRIVER RS232 INPUT A LOGIC INPUT A LT1080 #2 RECEIVER RS232 INPUT B ON/OFF (CHANNEL SELECT) INPUT LOGIC INVERTER LT1080 #2 DRIVER LOGIC OUTPUT LOGIC INVERTER 1080/81 F04 RS232 TRANSMISSION LINE LOGIC INPUT B ON/OFF (CHANNEL SELECT) INPUT LOGIC INVERTER 1080/81 F05 10801fe 6 LT1080/LT1081 U U W U APPLICATIO S I FOR ATIO The generated driver supplies (V + and V –) may be used to power external circuitry such as other RS232 drivers or op amps. They should be loaded with care, since excessive loading can cause the generated supply voltages to drop, causing the RS232 driver output voltages to fall below RS232 requirements. See the graph “Supply Generator Outputs” for a comparison of generated supply voltage versus supply current. When driving CMOS logic from a receiver that will be used in the SHUTDOWN mode and there is no other active receiver on the line, a 51k resistor can be placed from the logic input to VCC to force a definite logic level when the receiver output is in a high impedance state. VCC LT1080 RECEIVER 51k* RS232 INPUT CMOS LOGIC LOGIC OUTPUT EXTERNAL OP AMP + 3 1µF LT1080 ON/OFF INPUT V+ DRIVER * FORCES LOGIC INPUT STATE WHEN VON/OFF IS LOW + V+ 1080/81 F06 – To protect against receiver input overloads in excess of ±30V, a voltage clamp can be placed on the data line and still maintain RS232 compatibility. 16 GND V– V– 7 1µF RS232 INPUT RECEIVER 1k* 1080/81 F08 30V LOGIC OUTPUT 5k 30V * A PTC THERMISTOR WILL ALLOW CONTINUOUS OVERLOAD OF GREATER THAN ±100V 1080/81 F067 U TYPICAL APPLICATIO Operating with 5V and 12V 12V INPUT* 2 17 4 3 5V INPUT LT1080 5 1µF LOGIC INPUTS 7 6 12 15 11 8 13 14 RS232 OUTPUT RS232 OUTPUT RS232 INPUT 5k LOGIC OUTPUTS 10 ON/OFF –12V OUTPUT 1µF 18 * PIN 1 USED ON LT1081. 9 5k RS232 INPUT 16 1080/81 • TA03 10801fe 7 LT1080/LT1081 U PACKAGE DESCRIPTIO J Package 16-Lead CERDIP (Narrow .300 Inch, Hermetic) (Reference LTC DWG # 05-08-1110) CORNER LEADS OPTION (4 PLCS) 0.005 (0.127) MIN 0.023 – 0.045 (0.584 – 1.143) HALF LEAD OPTION 0.840 (21.336) MAX 16 15 14 12 13 11 10 9 0.220 – 0.310 (5.588 – 7.874) 0.025 (0.635) RAD TYP 0.045 – 0.068 (1.143 – 1.727) FULL LEAD OPTION 2 1 3 5 4 6 7 8 0.200 (5.080) MAX 0.300 BSC (0.762 BSC) 0.015 – 0.060 (0.380 – 1.520) 0.008 – 0.018 (0.203 – 0.457) 0° – 15° NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS 0.045 – 0.065 (1.143 – 1.651) 0.125 (3.175) MIN 0.100 (2.54) BSC 0.014 – 0.026 (0.360 – 0.660) J16 1298 J Package 18-Lead CERDIP (Narrow .300 Inch, Hermetic) (Reference LTC DWG # 05-08-1110) CORNER LEADS OPTION (4 PLCS) 0.005 (0.127) MIN 0.023 – 0.045 (0.584 – 1.143) HALF LEAD OPTION 0.960 (24.384) MAX 18 17 16 15 14 13 12 11 10 0.220 – 0.310 (5.590 – 7.870) 0.025 (0.635) RAD TYP 0.045 – 0.068 (1.143 – 1.727) FULL LEAD OPTION 1 2 3 4 5 6 7 8 9 0.200 (5.080) MAX 0.300 BSC (0.762 BSC) 0.015 – 0.060 (0.380 – 1.520) 0.008 – 0.018 (0.203 – 0.457) 0° – 15° NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS 0.125 (3.175) MIN 0.045 – 0.065 (1.143 – 1.651) 0.014 – 0.026 (0.360 – 0.660) 0.100 (2.54) BSC J18 1298 OBSOLETE PACKAGES 10801fe 8 LT1080/LT1081 U PACKAGE DESCRIPTIO N Package 16-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) 0.770* (19.558) MAX 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 0.255 ± 0.015* (6.477 ± 0.381) 0.130 ± 0.005 (3.302 ± 0.127) 0.300 – 0.325 (7.620 – 8.255) 0.009 – 0.015 (0.229 – 0.381) ( 0.020 (0.508) MIN +0.035 0.325 –0.015 8.255 +0.889 –0.381 0.045 – 0.065 (1.143 – 1.651) ) 0.065 (1.651) TYP 0.125 (3.175) MIN 0.018 ± 0.003 (0.457 ± 0.076) 0.100 (2.54) BSC *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm) N16 1098 N Package 18-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) 0.900* (22.860) MAX 18 17 16 15 14 13 12 11 10 1 2 3 4 5 6 7 8 9 0.255 ± 0.015* (6.477 ± 0.381) 0.130 ± 0.005 (3.302 ± 0.127) 0.300 – 0.325 (7.620 – 8.255) 0.009 – 0.015 (0.229 – 0.381) ( +0.035 0.325 –0.015 ) 0.020 (0.508) MIN 0.065 (1.651) TYP 0.125 (3.175) MIN 0.005 (0.127) MIN *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm) 8.255 +0.889 –0.381 0.045 – 0.065 (1.143 – 1.651) 0.100 (2.54) BSC 0.018 ± 0.003 (0.457 ± 0.076) N18 1098 10801fe 9 LT1080/LT1081 U PACKAGE DESCRIPTIO SW Package 16-Lead Plastic Small Outline (Wide .300 Inch) (Reference LTC DWG # 05-08-1620) 0.398 – 0.413* (10.109 – 10.490) 16 15 14 13 12 11 10 9 0.394 – 0.419 (10.007 – 10.643) NOTE 1 1 0.291 – 0.299** (7.391 – 7.595) 2 3 4 5 6 7 0.093 – 0.104 (2.362 – 2.642) 0.010 – 0.029 × 45° (0.254 – 0.737) 8 0.037 – 0.045 (0.940 – 1.143) 0° – 8° TYP 0.009 – 0.013 (0.229 – 0.330) NOTE 1 0.016 – 0.050 (0.406 – 1.270) 0.050 (1.270) BSC 0.004 – 0.012 (0.102 – 0.305) 0.014 – 0.019 (0.356 – 0.482) TYP NOTE: 1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS S16 (WIDE) 1098 *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 10801fe 10 LT1080/LT1081 U PACKAGE DESCRIPTIO SW Package 18-Lead Plastic Small Outline (Wide .300 Inch) (Reference LTC DWG # 05-08-1620) 0.447 – 0.463* (11.354 – 11.760) 18 17 16 15 14 13 12 11 10 0.394 – 0.419 (10.007 – 10.643) NOTE 1 0.291 – 0.299** (7.391 – 7.595) 1 2 3 4 5 6 7 8 9 0.093 – 0.104 (2.362 – 2.642) 0.010 – 0.029 × 45° (0.254 – 0.737) 0.037 – 0.045 (0.940 – 1.143) 0° – 8° TYP 0.009 – 0.013 (0.229 – 0.330) NOTE 1 0.016 – 0.050 (0.406 – 1.270) 0.050 (1.270) BSC 0.004 – 0.012 (0.102 – 0.305) 0.014 – 0.019 (0.356 – 0.482) TYP NOTE: 1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS S18 (WIDE) 1098 *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 10801fe Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 LT1080/LT1081 U TYPICAL APPLICATIO Supporting an LT1039 (Triple Driver/Receiver) SHUTDOWN 5V 18 ON/OFF VCC LT1080 17 18 VCC 17 ON/OFF LT1039 TTL INPUT RS232 OUTPUT TTL INPUT RS232 OUTPUT TTL INPUT RS232 OUTPUT TTL INPUT RS232 OUTPUT TTL INPUT RS232 OUTPUT RS232 INPUT TTL OUTPUT RS232 INPUT TTL OUTPUT 5k 30k RS232 INPUT TTL OUTPUT *C1 1µF 2 C1+ 4 C1– 30k RS232 INPUT TTL OUTPUT 5 1µF RS232 INPUT TTL OUTPUT 5k 6 30k C2 + C2 – V+ 3 1 V+ V– 7 9 V– GND 16 GND 1µF 1µF 10 1080/81 • TA02 *IN APPLICATIONS WHERE A SEPARATE SECOND POSITIVE SUPPLY IS AVAILABLE (SUCH AS 5V AND 12V), THE 12V SUPPLY MAY BE CONNECTED TO PIN 2 AND C1 DELETED. THE POWER SUPPLY CIRCUITRY WILL THEN INVERT THE 12V SUPPLY. THE 5V SUPPLY IS STILL NEEDED TO POWER THE BIASING CIRCUITRY AND RECEIVERS. RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1180A/LT1181A 5V Low Power 2DR/2TX RS232 Transceiver 0.1µF Capacitors, 10kV ESD LT1780/LT1781 5V Low Power 2DR/2TX RS232 Transceiver 15kV ESD LT1381 5V Low Power 2DR/2TX RS232 Transceiver 16-Pin Narrow SO Package LT1130A/LT1140A 5V RS232 Transceivers Up to 5DR/5RX LTC1383 5V Low Power 2DR/2RX RS232 Transceiver Low Supply Current ICC = 220µA LTC1386 3.3V Low Power EIA/TIA562 Transceiver Low Supply Current ICC = 200µA 10801fe 12 Linear Technology Corporation LT/CPI 1101 1.5K REV E • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 1991