MD1S THRU MD7S MINIATURE GLASS PASSIVATED SINGLE PHASE SURFACE MOUNT BRIDGE RECTIFIER Reverse Voltage – 50 to 1000 Volts Forward Current – 0.5 Ampere + Features ~ (1): - ~ ~ ~ (4):+ (2): (3): • Surge overload rating: 30 amperes peak - • Ideal for printed circuit board • Low leakage • Reliable low cost construction utilizing molded • Plastic package has Underwriters Laboratory Flammability Classification 94V-O Mechanical Data • Case: MD-S, molded plastic. • Terminals: Leads solderable per MIL-STD-202, method 208. • Mounting position: Any. • Weight: 0.008 ounce, 0.22 grams. Absolute Maximum Ratings and Characteristics Ratings at 250C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Symbols MD1S MD2S MD3S MD4S MD5S MD6S MD7S Units Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 V Maximum RMS voltage VRMS 35 70 140 280 420 560 700 V Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 V Maximum average forward rectified current See Fig .1 On glass epoxy P.C.B(Note 2) On aluminum substrate(Note 3) I(AV) 0.5 0.8 A Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 30 A VF 1.0 V IR 5.0 500 µA CJ 13 Maximum forward voltage at 0.4A DC Maximum reverse current at rated DC blocking voltage @TA = 25 OC @TA = 125OC Typical junction capacitance (Note 1) Typical thermal resistance (Note 3) Typical thermal resistance (Note 2) Operating and storage temperature range pF 70 O C/W RθJL 20 O C/W TJ ,TS -55 to+150 RθJA O C Notes: (1) Measured at 1 MHZ and applied Vr = 4volts. (2) On glass epoxy P.C.B. mounted on 0.05 x 0.05” (1.3 x 1.3 mm) pads. (3) On aluminum substrate P.C.B. with an area of 0.8 x 0.8” (20 x 20mm) mounted on 0.05 x 0.05” (1.3 x 1.3mm) solder pad. SEMTECH ELECTRONICS LTD. ® (Subsidiary of Semtech International Holdings Limited, acompany listed on the Hong Kong Stock Exchange, Stock Code: 724) Dated : 23/02/2005 H MD1S THRU MD7S Typical Forward Voltage Characteristics per element 10 0.8 Forward Current, A Average Forward Rectified Current, A Derating curve for output rectified current 0.6 Aluminum substrate 0.4 Glass epoxy P.C.B. 0.2 Resistive or inductive load 0 0 120 80 40 Tj=150 C 0.1 Pulse width=300 s 1% duty cycle 0.01 160 0.2 1.4 1.0 0.6 Ambient Temperature ( C) Forward Voltage, V Typical Reverse Leakage Characteristics per leg Max Non-repetitive Peak Forward Surge Current per leg 100 Instantaneous Reverse Leakage Current, A 35 Peak Forward Surge Current, A Tj=25 C 1.0 TA=40 C single half sine-wave JEDEC method 30 f=60Hz f=50Hz 20 10 1 cycle Tj=125 C 10 1.0 0.1 Tj=25 C 0.01 0 1 100 10 0 40 100 80 Percent of Rated Peak Reverse Voltage, % Number Of Cycles Typical Junction Capacitance Per Leg Junction Capacitance, pF 30 Tj=25 C f=1MHz Vaig=50mVp-p 20 10 0 0.1 1 10 100 200 Reverse Voltage, V SEMTECH ELECTRONICS LTD. ® (Subsidiary of Semtech International Holdings Limited, acompany listed on the Hong Kong Stock Exchange, Stock Code: 724) Dated : 23/02/2005 H