September 2007 HY[B/I]39S256[40/80/16]0FT(L) HY[B/I]39S256[40/80/16]0FE(L) HYB39S256[40/80/16]0FF(L) HYB39S 256407 F E 256-MBit Synchronous DRAM SDRAM Internet Data Sheet Rev. 1.42 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM HY[B/I]39S256[40/80/16]0FT(L), HY[B/I]39S256[40/80/16]0FE(L), HYB39S256[40/80/16]0FF(L), HYB39S256407FE Revision History: 2007-09, Rev. 1.42 Page Subjects (major changes since last revision) All Adapted internet edition 7 Corrected SDRAM organization for x4 in Table 4 Previous Revision: 2007-09, Rev. 1.41 All Editorial Change 4 Corrected HYB39S256407FF-7 to HYP39S256407FE-7 Previous Revision: 2007-04, Rev. 1.40 4 Corrected HYB39S256400FE-7 to HYB39S256400FF-7 Previous Revision: 2007-03, Rev. 1.30 We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: [email protected] qag_techdoc_rev400 / 3.2 QAG / 2006-08-07 03292006-TMTK-JFEU 2 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM 1 Overview This chapter lists all main features of the product family HYB39S256[400/800/160]F[E/T/F](L) and the ordering information. 1.1 • • • • • • • • • • Features Fully Synchronous to Positive Clock Edge 0 to 70 °C Standard Operating Temperature -40 to 85 °C Industrial Operating Temperature Four Banks controlled by BA0 & BA1 Programmable CAS Latency: 2 & 3 Programmable Wrap Sequence: Sequential or Interleave Programmable Burst Length: 1, 2, 4, 8 and full page Multiple Burst Read with Single Write Operation Automatic and Controlled Precharge Command Data Mask for Read / Write control (x4, x8) • • • • • • • • Data Mask for Byte Control (x16) Auto Refresh (CBR) and Self Refresh Power Down and Clock Suspend Mode 8192 refresh cycles / 64 ms (7.8 μs) Random Column Address every CLK (1-N Rule) Single 3.3 V ± 0.3 V Power Supply LVTTL Interface versions Packages: – P(G)–TSOPII–54 (400mil width) – PG–TFBGA–54 TABLE 1 Performance Poduct Type Speed Code –6 –7 Unit Speed Grade PC166–333 PC133–222 — 166 143 MHz 6 7 ns 5.4 5.4 ns 7.5 7.5 ns 5.4 5.4 ns Max. Clock Frequency @CL3 @CL2 Rev. 1.42, 2007-09 03292006-TMTK-JFEU fCK3 tCK3 tAC3 tCK2 tAC2 3 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM 1.2 Description The HYB39S256[400/800/160]F[E/T/F](L) are four bank Synchronous DRAMs organized as 4 banks x 16 MBit x4, 4 banks x 8 MBit x8 and 4 banks x 4 Mbit x16 respectively. These synchronous devices achieve high speed data transfer rates for CAS latencies by employing a chip architecture that prefetches multiple bits and then synchronizes the output data to a system clock. The chip is fabricated with Qimonda’s advanced 0.11-μm 256-MBit DRAM process technology. The device is designed to comply with all industry standards set for synchronous DRAM products, both electrically and mechanically. All of the control, address, data input and output circuits are synchronized with the positive edge of an externally supplied clock. Operating the four memory banks in an interleave fashion allows random access operation to occur at a higher rate than is possible with standard DRAMs. A sequential and gapless data rate is possible depending on burst length, CAS latency and speed grade of the device. Auto Refresh (CBR) and Self Refresh operation are supported. These devices operate with a single 3.3 V ± 0.3 V power supply. All 256-Mbit components are available in P(G)–TSOPII–54 and PG–TFBGA–54 packages. TABLE 2 Ordering Information for RoHS Compliant Products Product Type Speed Grade Description Package Note 143MHz 64M x 4 SDRAM PG-TFBGA-54 1) Standard Operating Temperature HYB39S256407FE-7 PC133-222 HYB39S256400FF-7 PG-TFBGA-54 HYB39S256400FE-7 PG-TSOPII-54 HYB39S256400FFL-7 PG-TFBGA-54 HYB39S256400FEL-7 PG-TSOPII-54 HYB39S256800FF-7 143MHz 32M x 8 SDRAM PG-TFBGA-54 HYB39S256800FE-7 PG-TSOPII-54 HYB39S256800FFL-7 PG-TFBGA-54 HYB39S256800FEL-7 PG-TSOPII-54 HYB39S256160FF-7 143MHz 16M x 16 SDRAM PG-TFBGA-54 HYB39S256160FE-7 PG-TSOPII-54 HYB39S256160FFL-7 PG-TFBGA-54 HYB39S256160FEL-7 PG-TSOPII-54 HYB39S256160FF-6 166MHz 16M x 16 SDRAM PG-TFBGA-54 HYB39S256160FE-6 PG-TSOPII-54 HYB39S256160FFL-6 PG-TFBGA-54 HYB39S256160FEL-6 PG-TSOPII-54 Industrial Operating Temperature HYI39S256800FE-7 HYI39S256160FE-7 PC166-333 143MHz 32M x 8 SDRAM PG-TSOPII-54 1) 143MHz 16M x 16 SDRAM 1) RoHS Compliant Product: Restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment as defined in the directive 2002/95/EC issued by the European Parliament and of the Council of 27 January 2003. These substances include mercury, lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers. Rev. 1.42, 2007-09 03292006-TMTK-JFEU 4 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM TABLE 3 Ordering Information for Lead-Containing Products Product Type Speed Grade Description Package 143MHz 64M x 4 SDRAM P-TSOPII-54 Standard Operating Temperature HYB39S256400FT-7 PC133-222 HYB39S256400FTL-7 HYB39S256800FT-7 143MHz 32M x 8 SDRAM HYB39S256800FTL-7 HYB39S256160FT-7 143MHz 16M x 16 SDRAM HYB39S256160FTL-7 HYB39S256160FT-6 166MHz 16M x 16 SDRAM Industrial Operating Temperature HYI39S256800FT-7 PC133-222 143MHz 32M x 8 SDRAM HYI39S256160FT-7 143MHz 16M x 16 SDRAM Note: For product nomenclature see Chapter 6 of this data sheet Rev. 1.42, 2007-09 03292006-TMTK-JFEU 5 P-TSOPII-54 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM 2 Configuration This chapter contains the pin configuration table, the TSOP and FBGA package drawing, and the block diagrams for the ×4, ×8, ×16 organization of the SDRAM. 2.1 Pin Description Listed below are the pin configurations sections for the various signals of the SDRAM. TABLE 4 Pin Configuration of the SDRAM Ball No. Name Pin Type Buffer Type Function Clock Signals ×4/×8/×16 Organization 38,2F CLK I LVTTL Clock Signal CK 37, 3F CKE I LVTTL Clock Enable Control Signals ×4/×8/×16 Organization 18, 8F RAS I LVTTL 17, 7F CAS I LVTTL 16, 9F WE I LVTTL 19, 9G CS I LVTTL Row Address Strobe (RAS), Column Address Strobe (CAS), Write Enable (WE) Chip Select Address Signals ×4/×8/×16 Organization 20, 7G BA0 I LVTTL 21, 8G BA1 I LVTTL 23, 7H A0 I LVTTL 24, 8H A1 I LVTTL 25, 8J A2 I LVTTL 26, 7J A3 I LVTTL 29, 3J A4 I LVTTL 30, 2J A5 I LVTTL 31, 3H A6 I LVTTL 32, 2H A7 I LVTTL 33, 1H A8 I LVTTL 34, 3G A9 I LVTTL 22, 9H A10 I LVTTL 35, 2G A11 I LVTTL 36, 1G A12 I LVTTL Rev. 1.42, 2007-09 03292006-TMTK-JFEU Bank Address Signals 1:0 Address Signal 12:0, Address Signal 10/Auto precharge 6 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM Ball No. Name Pin Type Buffer Type Function Data Signals ×4 Organization 5, 8B DQ0 I/O LVTTL 11, 8D DQ1 I/O LVTTL 44, 2D DQ2 I/O LVTTL 50, 2B DQ3 I/O LVTTL Data Signal Bus 3:0 Data Signals ×8 Organization 2, 8A DQ0 I/O LVTTL 5, 8B DQ1 I/O LVTTL 8, 8C DQ2 I/O LVTTL 11, 8D DQ3 I/O LVTTL 44, 2D DQ4 I/O LVTTL 47, 2C DQ5 I/O LVTTL 50, 2B DQ6 I/O LVTTL 53, 2A DQ7 I/O LVTTL Data Signal Bus 7:0 Data Signals ×16 Organization 2, 8A DQ0 I/O LVTTL 4, 9B DQ1 I/O LVTTL 5, 8B DQ2 I/O LVTTL 7, 9C DQ3 I/O LVTTL 8, 8C DQ4 I/O LVTTL 10, 9D DQ5 I/O LVTTL 11, 8D DQ6 I/O LVTTL 13, 9E DQ7 I/O LVTTL 42, 1E DQ8 I/O LVTTL 44, 2D DQ9 I/O LVTTL 45, 1D DQ10 I/O LVTTL 47, 2C DQ11 I/O LVTTL 48, 1C DQ12 I/O LVTTL 50, 2B DQ13 I/O LVTTL 51, 1B DQ14 I/O LVTTL 53, 2A DQ15 I/O LVTTL Data Signal Bus 15:0 Data Mask ×4/×8 Organization 39, 1F DQM I/O LVTTL Data Mask Data Mask ×16 Organization 39, 1F UDQM I/O LVTTL Data Mask Upper Byte 15, 8E LDQM I/O LVTTL Data Mask Lower Byte Power Supplies ×4/×8/×16 Organization 3B, 3D, 7A, 7C VDDQ PWR Rev. 1.42, 2007-09 03292006-TMTK-JFEU – Power Supply 7 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM Ball No. Name Pin Type Buffer Type Function 7E, 9A, 9J VDD PWR – Power Supply 3A, 3C, 7B, 7D VSSQ PWR – Power Supply Ground for DQs 1J, 1A, 3E VSS PWR – Power Supply Ground Not connected ×4 Organization 2, 4, 7, 8, NC 10, 13, 15, 40, 42, 45, 47, 48, 51, 53, 1B, 1C, 1D, 1E, 2A, 2C, 2E, 8A, 8C, 8E, 9B, 9C, 9D, 9E NC – Not connected Not connected ×8 Organization 7, 10, 13, NC 15, 40, 42, 45, 48, 51, 1B, 1C, 1D, 1E, 2E, 8E, 9B, 9C, 9D, 9E NC – Not connected Not connected ×16 Organization 40, 2E NC NC Rev. 1.42, 2007-09 03292006-TMTK-JFEU – Not connected 8 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM 2.2 Package P(G)–TSOPII–54 Listed below are the pin outs of the TSOP package. FIGURE 1 Pinouts P(G)–TSOPII–54 0[ 0 [ 0 [ 6 '' 6'' 6'' '4 '4 1& 6 ''4 6''4 6''4 '4 '4 1& '4 1& '4 6 664 6664 6664 '4 '4 1& '4 1& 1& 6 ''4 6''4 6''4 '4 '4 1& '4 1& '4 6 664 6664 6664 '4 1& 1& 6 '' 6'' 6'' /'4 0 :( &$6 5$6 &6 %$ %$ $ $ 3 $ $ $ $ 1& :( &$6 5$6 &6 %$ %$ $ $3 $ $ $ $ 1& :( &$6 5$6 &6 %$ %$ $ $3 $ $ $ $ 6 '' 6'' 6'' 6 66 666 666 1& '4 '4 6 664 6664 6664 1& '4 1& '4 '4 '4 6 ''4 6''4 6''4 1& 1& 1& '4 '4 '4 6 664 6664 6664 1& '4 1& '4 '4 '4 6 ''4 6''4 6''4 1& 1& '4 6 66 666 666 1& '40 &/. &.( $ $ $ $ $ $ $ $ 1& '40 &/. &.( $ $ $ $ $ $ $ $ 1& 8'4 0 &/. &.( $ $ $ $ $ $ $ $ 6 66 666 666 762 3,, P LO[ PLO P PSLW FK 633 Rev. 1.42, 2007-09 03292006-TMTK-JFEU 9 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM 2.3 Package PG–TFBGA–54 Listed below are the ball outs of the TFBGA package. • Figure 2 “Ballout for ×16 components, TFBGA-54 (top view)” on Page 10 • Figure 3 “Ballout for ×8 components, TFBGA-54 (top view)” on Page 11 • Figure 4 “Ballout for ×4 components, TFBGA-54 (top view)” on Page 12 FIGURE 2 Ballout for ×16 components, TFBGA-54 (top view) 666 '4 6664 $ 6''4 '4 6'' '4 '4 6''4 % 6664 '4 '4 '4 '4 6664 & 6''4 '4 '4 '4 '4 6''4 ' 6664 '4 '4 '4 1& 666 ( 6'' /'4 0 '4 8'4 0 &/. &.( ) &$6 5$6 :( $ $ $ * %$ %$ &6 $ $ $ + $ $ $ 666 $ $ - $ $ 6'' 033' Rev. 1.42, 2007-09 03292006-TMTK-JFEU 10 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM FIGURE 3 Ballout for ×8 components, TFBGA-54 (top view) 666 '4 6664 $ 6''4 '4 6'' 1& '4 6''4 % 6664 '4 1& 1& '4 6664 & 6''4 '4 1& 1& '4 6''4 ' 6664 '4 1& 1& 1& 666 ( 6'' 1& 1& '40 &/. &.( ) &$6 5$6 :( $ $ $ * %$ %$ &6 $ $ $ + $ $ $ 666 $ $ - $ $ 6'' 033' Rev. 1.42, 2007-09 03292006-TMTK-JFEU 11 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM FIGURE 4 Ballout for ×4 components, TFBGA-54 (top view) $ 6''4 1& 6'' 6''4 % 6664 '4 1& 1& 6664 & 6''4 1& 1& 1& '4 6''4 ' 6664 '4 1& 1& 1& 666 ( 6'' 1& 1& '40 &/. &.( ) &$6 5$6 :( $ $ $ * %$ %$ &6 $ $ $ + $ $ $ 666 $ $ - $ $ 6'' 666 1& 6664 1& '4 1& 033' Rev. 1.42, 2007-09 03292006-TMTK-JFEU 12 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM 3 Functional Description This chapter contains the functional description. TABLE 5 Truth Table: Operation Command Operation Device State CKE n-11)2) CKE n1)2) DQM 1)2) BA0 BA11)2) AP= A101)2) Addr. CS1 RAS 1)2) )2) 1)2) CAS1 WE )2) 1)2) Bank Active Idle3) H X X V V V L L H H Bank Precharge Any H X X V L X L L H L Precharge All Any H X X X H X L L H L Write Active3) H X X V L V L H L L Write with Auto precharge Active 3) H X X V H V L H L L Read Active3) H X X V L V L H L H 3) H X X V H V L H L H Read with Auto precharge Active Mode Register Set Idle H X X V V V L L L L No Operation Any H X X X X X L H H H Burst Stop Active H X X X X X L H H L Device Deselect Any H X X X X X H X X X Auto Refresh Idle H H X X X X L L L H Self Refresh Entry Idle H L X X X X L L L H Self Refresh Exit Idle (Self Refr.) L H X X X X H X X X L H H X Power Down/ Clock Suspend Entry Active or Idle or Burst H L X X X X H X X X L H H H Power Down/ Clock Suspend Exit Active or Idle or Burst L H X X X L H H H Data Write/ Output Enable Active H X L X X X X X X X Data Write/ Output Disable Active H X H X X X X X X X H X X X X 1) V = Valid, x = Don’t Care, L = Low Level, H = High Level 2) CKEn signal is input level when commands are provided, CKEn-1 signal is input level one clock before the commands are provided. 3) This is the state of the banks designated by BA0, BA1 signals. Rev. 1.42, 2007-09 03292006-TMTK-JFEU 13 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM %$ %$ $ $ $ $ :%/ $ $ 70 Z UHJDGGU $ $ $ $ $ $ &/ %7 %/ Z Z Z $ 03%6 TABLE 6 Mode Register Definition (BA1:0 = 00B) Field Bits Type Description BL 2:0 w Burst Length Note: All other bit combinations are RESERVED 000B 001B 010B 011B 111B 1 2 4 8 Full Page (Sequential burst type only) BT 3 Burst Type Sequential 0B 1B Interleaved CL 6:4 CAS Latency Number of full clocks from read command to first data valid window. Note: All other bit combinations are RESERVED. 010B 2 011B 3 TM 8:7 Test Mode Note: All other bit combinations are RESERVED. 00B WBL Mode register set 9 Write Burst Length 0B Burst write 1B Single bit write 12:10 Reserved, set to zero Rev. 1.42, 2007-09 03292006-TMTK-JFEU 14 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM TABLE 7 Burst Length and Sequence Burst Length Starting Column Address A2 A1 A0 Type=Sequential Type=Interleaved 0 0–1 0–1 1 1–0 1–0 0 0 0–1–2–3 0–1–2–3 0 1 1–2–3–0 1–0–3–2 1 0 2–3–0–1 2–3–0–1 2 4 8 FullPage Order of Accesses Within a Burst 1 1 3–0–1–2 3–2–1–0 0 0 0 0–1–2–3–4–5–6–7 0–1–2–3–4–5–6–7 0 0 1 1–2–3–4–5–6–7–0 1–0–3–2–5–4–7–6 0 1 0 2–3–4–5–6–7–0–1 2–3–0–1–6–7–4–5 0 1 1 3–4–5–6–7–0–1–2 3–2–1–0–7–6–5–4 1 0 0 4–5–6–7–0–1–2–3 4–5–6–7–0–1–2–3 1 0 1 5–6–7–0–1–2–3–4 5–4–7–6–1–0–3–2 1 1 0 6–7–0–1–2–3–4–5 6–7–4–5–2–3–0–1 1 1 1 7–0–1–2–3–4–5–6 7–6–5–4–3–2–1–0 Cn, Cn+1, Cn+2 .... not supported n Notes 1. 2. 3. 4. For a burst length of two, A1-Ai selects the two-data-element block; A0 selects the first access within the block. For a burst length of four, A2-Ai selects the four-data-element block; A0-A1 selects the first access within the block. For a burst length of eight, A3-Ai selects the eight-data- element block; A0-A2 selects the first access with in the block. Whenever a boundary of the block is reached within a given sequence above, the following access wraps within the block. Rev. 1.42, 2007-09 03292006-TMTK-JFEU 15 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM 4 Electrical Characteristics This chapter lists the electrical characteristics. 4.1 Operating Conditions This chapter describes the operating conditions. TABLE 8 Absolute Maximum Ratings Parameter Input / Output voltage relative to VSS Voltage on VDD supply relative to VSS Voltage on VDDQ supply relative to VSS Operating Temperature for HYB... Operating Temperature for HYI... Storage temperature range Power dissipation per SDRAM component Data out current (short circuit) Symbol Limit Values VIN, VOUT VDD VDDQ TA TA TSTG PD IOUT Unit Note/ Test Condition Min. Max. – 1.0 +4.6 V – – 1.0 +4.6 V – – 1.0 +4.6 V – 0 +70 °C – – 40 +85 °C – -55 +150 °C – – 1 W – – 50 mA – Attention: Stresses above the max. values listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the integrated circuit. Rev. 1.42, 2007-09 03292006-TMTK-JFEU 16 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM TABLE 9 DC Characteristics Parameter Symbol Values Min. Max. VDD I/O Supply Voltage VDDQ Input high voltage VIH Input low voltage VIL Output high voltage (IOUT = – 4.0 mA) VOH Output low voltage (IOUT = 4.0 mA) VOL Input leakage current, any input (0 V < VIN < VDD, all other inputs = 0 V) IIL IOL Output leakage current (DQs are disabled, 0 V < VOUT < VDDQ) Supply Voltage Unit Note1)/ Test Condition 3.0 3.6 V 2) 3.0 3.6 V 2) 2.0 VDDQ + 0.3 V 2)3) – 0.3 +0.8 V 2)3) 2.4 – V 2) – 0.4 V 2) –5 +5 μA – –5 +5 μA – 1) TA = 0 to 70 °C 2) All voltages are referenced to VSS 3) VIH may overshoot to VDDQ + 2.0 V for pulse width of < 4ns with 3.3 V. VIL may undershoot to -2.0 V for pulse width < 4.0 ns with 3.3 V. Pulse width measured at 50% points with amplitude measured peak to DC reference. TABLE 10 Input and Output Capacitances Parameter Symbol Values 1) Min. Max. Unit Note 2) Input Capacitances: CK CI1 2.5 3.5 pF Input Capacitance (A0-A12, BA0, BA1, RAS, CAS, WE, CS, CKE, DQM) CI2 2.5 3.8 pF Input/Output Capacitance (DQ) CI0 4.0 6.0 pF 1) Capacitance values are shown for TSOP-54 packages. Capacitance values for TFBGA packages are lower by 0.5 pF 2) TA = 0 to 70 °C; VDD,VDDQ = 3.3 V ± 0.3 V, f = 1 MHz TABLE 11 IDD Conditions Parameter Symbol Operating Current One bank active, Burst length = 1 IDD1 Precharge Standby Current in Power Down Mode IDD2P IDD2N IDD3N IDD3P IDD4 Recharge Standby Current in Non-Power Down Mode No Operating Current Active state (max. 4 banks) Burst Operating Current Read command cycling IDD5 Auto Refresh Current Auto Refresh command cycling Rev. 1.42, 2007-09 03292006-TMTK-JFEU 17 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM Parameter Symbol Self Refresh Current (standard components) Self Refresh Mode, CKE=0.2V, tCK=infinity IDD6 Self Refresh Current (low power components) Self Refresh Mode, CKE=0.2V, tCK=infinity TABLE 12 IDD Specifications and Conditions Symbol –6 –7 Unit Note/ Test Condition1)2) Max. IDD1 IDD2P IDD2N IDD3N IDD3P IDD4 IDD5 tRC = tRC(min), IO = 0 mA CS =VIH (min.), CKE ≤VIL(max) CS =VIH (min.), CKE≥ VIH(min) CS = VIH(min), CKE ≥VIH(min.) CS = VIH(min), CKE ≤ VIL(max.) tRFC = tRFC(min) tRFC= 7.8 μs IDD6 100 80 mA 3)4) 2 2 mA 2) 26 22 mA 2) 40 35 mA 2) 5 5 mA 2) 65 57 mA 2)3) 168 142 mA 5) 25 25 mA 3 3 mA 1.05 1.05 mA Standard components Low power components 6) 1) Currents values will be added when available. 2) TA = 0 to 70 °C; VSS = 0 V; VDD, VDDQ = 3.3 V ± 0.3 V 3) These parameters depend on the cycle rate. All values are measured at 166 MHz for -6, at 133 MHz for -7 and -7.5 and at 100 MHz for 8 components with the outputs open. Input signals are changed once during tCK. 4) These parameters are measured with continuous data stream during read access and all DQ toggling. CL=3 and BL=4 is assumed and the VDDQ current is excluded. 5) tRFC = tRFC(min) “burst refresh”, tRFC =7.8 μs “distributed refresh“ 6) 1.05 mA at 85 °C, 1.00 mA at 60 °C Rev. 1.42, 2007-09 03292006-TMTK-JFEU 18 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM 4.2 AC Characteristics This chapter lists the AC characteristics. TABLE 13 AC Timing - Absolute Specifications Parameter Symbol –7 –6 PC143–333 PC166–333 Min. Max. Min. Max. Unit Note1)2)3) Clock and Clock Enable Clock Frequency tCK 7 7.5 — — 6 7.5 — — ns ns CL3 CL2 Access Time from Clock tAC — — 5.4 5.4 — — 5.4 5.4 ns ns CL3 CL2 3)4)5) Clock High Pulse Width Clock Low Pulse Width Transition time tCH tCL tT 2.5 — 2 — ns 2.5 — 2 — ns 0.3 1.2 0.3 1.2 ns tIS tIH tCKS tCKH tRSC tSB 1.5 — 1.5 — ns 6) 0.8 — 0.8 — ns 6) 1.5 — 1.5 — ns 6) 0.8 — 0.8 — ns 6) 2 — 2 — tCK 0 7 0 6 ns tRCD tRP tRAS tRC tRFC tRRD tCCD 15 — 15 — ns 7) 15 — 15 — ns 7) 37 100k 36 100k ns 7) 60 — 60 — ns 7) 63 — 60 — ns 14 — 12 — ns 1 — 1 — tCK tREF tSREX tOH – 64 – 64 ms 1 — 1 — tCK 3 — 2.5 — ns tLZ tHZ tDQZ 0 — 0 — ns 3 7 3 6 ns — 2 — 2 tCK Setup and Hold Times Input Setup Time Input Hold Time CKE Setup Time CKE Hold Time Mode Register Set-up to Active delay Power Down Mode Entry Time Common Parameters Row to Column Delay Time Row Precharge Time Row Active Time Row Cycle Time Row Cycle Time during Auto Refresh Activate(a) to Activate(b) Command period CAS(a) to CAS(b) Command period 7) Refresh Cycle Refresh Period (8192 cycles) Self Refresh Exit Time Data Out Hold Time Read Cycle Data Out to Low Impedance Time Data Out to High Impedance Time DQM Data Out Disable Latency Rev. 1.42, 2007-09 03292006-TMTK-JFEU 19 3)5) Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM Parameter Symbol –7 –6 PC143–333 PC166–333 Unit Note1)2)3) Min. Max. Min. Max. 14 — 12 — ns 8) 9) — tCK tCK Write Cycle tWR Last Data Input to Precharge (Write without Auto Precharge) Last Data Input to Activate(Write with Auto Precharge) tDAL(min.) tDQW DQM Write Mask Latency 0 — 0 1) TA = 0 to 70 °C; VSS = 0 V; VDD, VDDQ = 3.3 V ± 0.3 V, tT = 1 ns 2) For proper power-up see the operation section of this data sheet. 3) AC timing tests for LV-TTL versions have VIL = 0.4 V and VIH = 2.4 V with the timing referenced to the 1.4 V crossover point. The transition time is measured between VIH and VIL. All AC measurements assume tT = 1 ns with the AC output load circuit shown in figure below. Specified tAC and tOH parameters are measured with a 50 pF only, without any resistive termination and with an input signal of 1V / ns edge rate between 0.8 V and 2.0 V. 4) If clock rising time is longer than 1 ns, a time (tT/2 - 0.5) ns has to be added to this parameter. 5) Access time from clock tac is 4.6 ns for PC133 components with no termination and 0 pF load,Data out hold time toh is 1.8 ns for PC133 components with no termination and 0 pF load. 6) If tT is longer than 1 ns, a time (tT - 1) ns has to be added to this parameter. 7) These parameter account for the number of clock cycles and depend on the operating frequency of the clock, as follows:the number of clock cycles = specified value of timing period (counted in fractions as a whole number) 8) It is recommended to use two clock cycles between the last data-in and the precharge command in case of a write command without AutoPrecharge. One clock cycle between the last data-in and the precharge command is also supported, but restricted to cycle times tck greater or equal the specified tWR value, where tck is equal to the actual system clock time. 9) When a Write command with Auto Precharge has been issued, a time of tDAL(min) has be fullfilled before the next Activate Command can be applied. For each of the terms, if not already an integer, round up to the next highest integer. tCK is equal to the actual system clock time. FIGURE 5 Measurement conditions for tAC and tOH t CH 2 .4 V 0 .4 V 1 .4 V CLO C K tCL t IS tT t IH IN P U T 1 .4 V tA C t LZ tAC tOH OUTPUT 1.4 V I/O t HZ 50 pF IO.vsd Rev. 1.42, 2007-09 03292006-TMTK-JFEU 20 Measurement conditions for tAC and tOH Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM 5 Package Outlines This chapter contains the package outlines of the products. FIGURE 6 *$8 *(3 /$1( [ [ 6($7 ,1 *3 /$1( 0 [ 0$ ; Package Outline P(G)-TSOPII-54 (top view) 0$ ; ,QGH[ 0D UNLQJ 'R HVQRWLQFOXGHS ODVWLFR UP HWD OSUR WUXV LRQR I P D [S HUV LGH 'R HVQRWLQFOXGHS ODVWLFS URWU XVLRQRI P D[S HUVLGH 'R HVQRWLQFOXGHG DPEDUSURWU XVLRQRI P D[S HUVLGH Notes 1. Drawing according to ISO 8015 2. Dimensions in mm 3. General tolerances +/- 0.15 Rev. 1.42, 2007-09 03292006-TMTK-JFEU 21 *3; Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM FIGURE 7 Package Outline P(G)-TFBGA-54 [ 0 $; % $ [ 0$ ; & 0 ,1 0 $; & ¡ [ ¡0 &$ % &6($7,1 *3 /$1( ¡0 & $ 0D UNLQJ%DOOVLGH % DG8Q LW0D UNLQ J %80 0 LGGOHRI3DFN DJ HV( GJHV *3$ Notes 1. Drawing according to ISO 8015 2. Dimensions in mm 3. General tolerances +/- 0.15 Rev. 1.42, 2007-09 03292006-TMTK-JFEU 22 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM 6 Product Nomenclature For reference the Qimonda SDRAM component nomenclature is enclosed in this chapter. TABLE 14 Examples for Nomenclature Fields Example for Field Number 1 2 3 4 5 SDRAM HYB 39 S 256 SDRAM HYI 39 S 256 6 7 8 9 10 11 80 0 F F –6 16 0 F E –7 TABLE 15 Memory Components Field Description Values Coding 1 Qimonda Component Prefix HYB Memory components HYI Memory components, industrial temperature range (-40°C – +85 °C) 2 Interface Voltage [V] 39 3.3 V 3 DRAM Technology S Single Data Rate SDRAM 4 Component Density [Mbit] 128 128 Mbit 256 256 Mbit 512 512 Mbit 40 ×4 80 ×8 16 ×16 0 .. 9 look up table 5+6 Number of I/Os 7 Product Variations 8 Die Revision 9 Package, Lead-Free Status C Third D Fourth F Fifth E TSOP, lead- and halogen-free F FBGA, lead- and halogen-free 10 Power – Standard power product 11 Speed Grade –6 PC166-333 –7 PC143-333, PC133-222 Rev. 1.42, 2007-09 03292006-TMTK-JFEU 23 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM List of Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Pinouts P(G)–TSOPII–54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Ballout for ×16 components, TFBGA-54 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Ballout for ×8 components, TFBGA-54 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Ballout for ×4 components, TFBGA-54 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Measurement conditions for tAC and tOH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Package Outline P(G)-TSOPII-54 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Package Outline P(G)-TFBGA-54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Rev. 1.42, 2007-09 03292006-TMTK-JFEU 24 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM List of Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Ordering Information for RoHS Compliant Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ordering Information for Lead-Containing Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin Configuration of the SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Truth Table: Operation Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Mode Register Definition (BA1:0 = 00B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Burst Length and Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Input and Output Capacitances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 IDD Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 IDD Specifications and Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 AC Timing - Absolute Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Examples for Nomenclature Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Memory Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Rev. 1.42, 2007-09 03292006-TMTK-JFEU 25 Internet Data Sheet HY[B/I]39S256[40/80/16][0/7]F[E/T/F](L) 256-MBit Synchronous DRAM Table of Contents 1 1.1 1.2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 2.1 2.2 2.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Package P(G)–TSOPII–54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Package PG–TFBGA–54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4 4.1 4.2 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6 Product Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Rev. 1.42, 2007-09 03292006-TMTK-JFEU 26 Internet Data Sheet Edition 2007-09 Published by Qimonda AG Gustav-Heinemann-Ring 212 D-81739 München, Germany © Qimonda AG 2007. All Rights Reserved. Legal Disclaimer The information given in this Internet Data Sheet shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Qimonda hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Qimonda Office. Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Qimonda Office. Qimonda Components may only be used in life-support devices or systems with the express written approval of Qimonda, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. www.qimonda.com