CRCW0201 Vishay Thick Film Rectangular, Chip Resistor FEATURES • Metal glaze on high quality ceramic • Protective overglaze • SnPb contacts on Ni barrier layer flow solderable • Automatic placement compatibility • Applications: cellular phones, memory modules, PCMCIA cards STANDARD ELECTRICAL SPECIFICATIONS MODEL CRCW0201 SIZE POWER RATING P70°C LIMITING ELEMENT VOLTAGE MAX TEMPERATURE TOLERANCE COEFFICIENT RESISTANCE RANGE INCH W V쓖 ppm/°C % Ω 0201 0.05 30 ≤ 200 5 10R – 1M0 E-SERIES 24 • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material • Ask about extended value ranges. • Marking: no marking TECHNICAL SPECIFICATIONS PARAMETER UNIT CRCW0201 W 0.05 V쓖 30 Insulation Voltage (1min) Vp 50 Insulation Resistance Ω > 10 Category Temperature Range °C - 55 / + 125 Failure Rate h-1 1*10-9 Weight / 1000 pieces g 0.17 Rated Dissipation at 70°C Limiting Element Voltage 1) Rated voltage: 1) 9 PxR ORDERING INFORMATION CRCW0201 100R J 200 P0 MODEL RESISTANCE VALUE Ω TOLERANCE J = ± 5% TC ppm/°C PACKAGING Papertape 10,000 pieces P0 = in Europe RT7 = in Americas/Asia www.vishay.com 34 For technical questions in Europe contact : [email protected] For technical questions in Americas/Asia contact : [email protected] Document Number 31050 Revision 21-Jan-02 CRCW0201 Vishay Thick Film Rectangular, Chip Resistor DIMENSIONS SIZE W mm 0.6 ±0.05 0.3 ±0.05 inch 0.024 ±.002 0.012 SIZE Rated Power In % DIMENSIONS H L ±.002 T1 T2 0.23 ±0.05 0.15 ±0.05 0.15 ±0.05 0.009 ±.002 0.006 ±.002 0.006 ±.002 SOLDER PAD DIMENSIONS a b l mm 0.28 0.43 0.23 inch 0.011 0.017 0.009 120 100 EIA* 80 60 40 20 CECC* 0 - 55 -25 0 25 50 Derating* 75 100 125 150 175 70 Ambient Temperature in °C *There are differences in board layout and measurements between CECC and EIA. PERFORMANCE TEST CONDITIONS OF TEST TEST RESULTS Endurance Test at 70°C IEC 60115-1 4.25.1 1000 hours at 70°C, 1.5 hours “ON”, 0.5 hours “OFF” ≤ ± 3.0% Endurance Test at UCT IEC 60115-1 4.25.3 1000 hours at 125°C without load ≤ ± 2.0% Overload Test IEC 60115-1 4.13 Short time overload at 2.5 x rated voltage or 2 x limiting element voltage, 0.5 seconds ≤ ± 1.0% Thermal Shock IEC 60115-1 4.19, IEC 60068-2-14 Rapid change between upper and lower category temperature ≤ ± 0.5% Damp Heat Steady State IEC 60115-1 4.24, IEC 60068-2-3 56 days at 40°C and 93% relative humidity at U = ≤ ± 2.0% Resistance to Soldering Heat IEC 60115-1 4.18, IEC 60068-2-20 10 seconds at 260°C solder bath temperature P/100 x R ≤ ± 1.0% APPLICABLE SPECIFICATIONS • CECC40000 / 40400 / EN 140 400 / IEC 60115 - 1 • EIA 575 • MIL-PRF-55342 Document Number 31050 Revision 21-Jan-02 For technical questions in Europe contact : [email protected] For technical questions in Americas/Asia contact : [email protected] www.vishay.com 35