Preliminary Specification Number : SP-KL1FX-G W-LAN Module Data Sheet Cypress Chipset for 802.11b/g/n Sample P/N : LBWA1KL1FX-TEMP Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 1 / 29 The revision history of the product specification Issued Date Apr. 29. 2015 Sep. 17, 2015 Revision Code A Revision Page Mar. 18. 2016 Oct 31, 2016 Dec 14, 2016 Feb 9, 2017 Feb 28, 2017 B C D E F G Change Reason P4 First Issue 4. Dimensions, Marking and Terminal Configurations: Change Pin14 NC to GND Reference schematic 4. Dimensions, Marking and Terminal Configurations, Add note of SDIO 4. Dimensions, Marking, and Terminal Configurations, Add pin 20, 27, 41 functional description. 6. Operating Condition, Add Specification Temperature Range 4. Dimensions, Marking and Terminal P8 6.1. Operating condition Correction P12 10. DC/RF Characteristics Correction P8 P24 P16 6.1. Operating condition APPENDIX 12. Reference Circuit IC Part Number Correction Addition Correction Changed P. 5 P.16 P.7 Oct. 29, 2015 Changed Items P.8 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Correction Addition Addition Preliminary Specification Number : SP-KL1FX-G 2 / 29 TABLE OF CONTENTS 1. Scope ..................................................................................................................................................... 3 2. Part Number ........................................................................................................................................... 3 3. Block Diagram ........................................................................................................................................ 3 4. Dimensions, Marking and Terminal Configurations ............................................................................... 4 5. Rating ..................................................................................................................................................... 8 6. Operating Condition ............................................................................................................................... 8 6.1. Operating condition ......................................................................................................................... 8 6.2. Power Up Sequence........................................................................................................................ 8 7. Digital I/O Requirements ........................................................................................................................ 9 8. External LPO Specification..................................................................................................................... 9 9. Interface Timing .................................................................................................................................... 10 9.1. SDIO Timing (Default Mode) ......................................................................................................... 10 9.2. SDIO Timing (High Speed Mode) ...................................................................................................11 10. DC/RF Characteristics........................................................................................................................ 12 10.1. DC/RF Characteristics for IEEE802.11b ..................................................................................... 12 10.2. DC/RF Characteristics for IEEE802.11g ..................................................................................... 13 10.3. DC/RF Characteristics for IEEE802.11n ..................................................................................... 14 11. Land pattern........................................................................................................................................ 15 12. Reference Circuit................................................................................................................................ 16 13. Tape and Reel Packing ...................................................................................................................... 17 14. NOTICE .............................................................................................................................................. 20 14.1. Storage Conditions: ..................................................................................................................... 20 14.2. Handling Conditions: ................................................................................................................... 20 14.3. Standard PCB Design (Land Pattern and Dimensions): ............................................................. 20 14.4. Notice for Chip Placer:................................................................................................................. 20 14.5. Soldering Conditions: .................................................................................................................. 21 14.6. Cleaning:...................................................................................................................................... 21 14.7. Operational Environment Conditions: ......................................................................................... 21 14.8. Input Power Capacity: ................................................................................................................. 22 15. PRECONDITION TO USE OUR PRODUCTS ................................................................................... 23 Please be aware that an important notice concerning availability, standard warranty and use in critical applications of Murata products and disclaimers thereto appears at the end of this specification sheet. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 3 / 29 1. Scope This specification is applied to the IEEE802.11b/g/n W-LAN module. - Interface - IC/Firmware - Reference Clock - MSL - RoHS : SDIO (WLAN) : Cypress/CYW43364 : Reference clock is embedded. : Level 3 : This module is compliant with the RoHS directive. 2. Part Number Sample Part Number EVK Part Number LBWA1KL1FX-TEMP LBWA1KL1FX-TEMP-D 3. Block Diagram Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 4 / 29 4. Dimensions, Marking and Terminal Configurations < Top View > B < Side View > < Bottom View > D 012345678 1FX C A Marking A B C D Dimensions Mark L a1 b1 c2 e2 e5 e8 Dimensions 6.95 +/- 0.2 0.25 +/- 0.10 0.30 +/- 0.2 0.50 +/- 0.1 0.2 +/- 0.1 1.175 +/- 0.100 0.50 +/- 0.10 Meaning Pin 1 Marking Murata Logo Module Type Inspection Number Mark W a2 b2 c3 e3 e6 m1 Dimensions 5.15 +/- 0.2 0.5 +/- 0.1 0.30 +/- 0.2 0.375 +/- 0.100 0.2 +/- 0.1 1.0 +/- 0.1 1.0 +/- 0.1 Mark T a3 c1 e1 e4 e7 m2 Structure Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. (unit : mm) Dimensions 1.1 max. 0.25 +/- 0.10 0.50 +/- 0.1 0.2 +/- 0.1 0.3 +/- 0.1 0.525 +/- 0.100 1.0 +/- 0.1 Preliminary Specification Number : SP-KL1FX-G 5 / 29 Terminal Configurations Connection to IC Terminal No. Terminal Name Type Description (1) GND - (2) NC - NC (3) NC - NC (4) NC - NC (5) NC - NC (6) NC - NC (7) NC - NC (8) NC - NC (9) NC - NC (10) NC - NC (11) NC - NC (12) GND - (13) NC - NC (14) GND - GND (15) WL_GPIO_4 I/O (16) NC - (17) WL_GPIO_2 I/O GPIO_2 (18) WL_GPIO_1 I/O GPIO_1 (19) GND - (20) SDIO_CLK I (21) GND - (22) SDIO_CMD (23) GPIO_4 NC SDIO_CLK SDIO clock input I/O SDIO_CMD SDIO command line SDIO_DATA_2 I/O SDIO_DATA_2 SDIO data line 2 (24) SDIO_DATA_0 I/O SDIO_DATA_0 SDIO data line 0 (25) SDIO_DATA_3 I/O SDIO_DATA_3 SDIO data line 3 (26) SDIO_DATA_1 I/O SDIO_DATA_1 SDIO data line 1 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 6 / 29 (27) WL_GPIO_0_HOST_ WAKE O GPIO_0 WLAN Host Wake WL_REG_ON Used by PMU to power up or power down the internal regulators used by the WLAN section. Also, when deasserted, this pin holds the WLAN section in reset. This pin has an internal 200kΩ pull-down resistor that is enabled by default. It can be disabled through programming. (28) WL_REG_ON I (29) GND - (30) VBAT PI (31) VIN_LDO PI (32) GND (SR_PVSS) - (33) GND (SR_PVSS) - (34) SR_VLX PO (35) GND - (36) VIO PI (37) LPO_IN (32kHz) I (38) NC - NC (39) NC - NC (40) GND - (41) ANT - (42) ～ (46) GND - LDO_VDDBAT5V, SR_VDDBAT5V LDO_VDD1P5, WLRF_VDD_1P35 SR_VLX CBUCK switching regulator output. SCC_VDDIO, SYS_VDDIO LPO_IN l External sleep clock input (32.768kHz). RF(WiFi) Signal Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 7 / 29 SDIO Pin Description No. Pin Name (i) SD 4-bit Mode (ii) SD 1-bit Mode 20 SDIO_CLK CLK Clock CLK Clock 24 SDIO_D0 DATA0 Data line 0 DATA Data line 26 SDIO_D1 DATA1 Data line 1 /Interrupt IRQ Interrupt 23 SDIO_D2 DATA2 Data line 2 NC Not used 25 SDIO_D3 DATA3 Data line 3 NC Not used 22 SDIO_CMD CMD Command line CMD Command line CLK SD Host CMD CLK CMD LBWA1KL1FX LBWA1KL1FX SD Host DATA DATA[3:0] (i) SD 4-bit Mode IRQ (ii) SD 1-bit Mode Note : 10 to 100kΩ pull-ups are required on the four DATA lines and the CMD line. This requirement must be met during all operating states by using external pull-up resisters or properly programming internal SDIO host pull-ups. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 8 / 29 5. Rating Storage Temperature Supply Voltage VBAT VDDIO min. -40 -0.5 -0.5 max. +85 5.0 3.9 unit deg.C V V * Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. No damage assuming only one parameter is set at limit at a time with all other parameters are set within operating condition. 6. Operating Condition 6.1. Operating condition Operating Temperature Range Specification Temperature Range VBAT Operating Voltage VDDIO VBAT Specification Voltage VDDIO min. -40 -10 3.0 1.71 3.2 1.71 typ. +25 +25 3.6 1.8 or 3.3 3.6 1.8 or 3.3 max. +85 +55 4.8 3.63 4.2 3.63 unit deg.C deg.C V V V V [Note] All RF characteristics in this datasheet are defined by Specification Temperature Range and Specification Voltage. 6.2. Power Up Sequence 32.768 kHz Sleep Clock 90% of VH VBAT VDDIO > 2 Sleep cycles WL_REG_ON Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 9 / 29 7. Digital I/O Requirements SDIO Interface I/O Pins Input low voltage (VDDIO = 3.3V) Input high voltage (VDDIO = 3.3V) Input low voltage (VDDIO = 1.8V)) Input high voltage (VDDIO = 1.8V) Output low voltage (VDDIO = 3.3V) Output high voltage (VDDIO = 3.3V) Output low voltage (VDDIO = 1.8V) Output high voltage (VDDIO = 1.8V) Sym VIL VIH VIL VIH VOL VOH VOL VOH min. 0.625*VDDIO 1.27 0.75*VDDIO 1.40 max. 0.25*VDDIO 0.58 0.125*VDDIO 0.45 - unit V V V V V V V V Other Digital I/O Pins Input low voltage (VDDIO = 3.3V) Input high voltage (VDDIO = 3.3V) Input low voltage (VDDIO = 1.8V)) Input high voltage (VDDIO = 1.8V) Output low voltage (VDDIO = 3.3V) Output high voltage (VDDIO = 3.3V) Output low voltage (VDDIO = 1.8V) Output high voltage (VDDIO = 1.8V) Sym VIL VIH VIL VIH VOL VOH VOL VOH min. 2.0 0.65*VDDIO VDDIO-0.4 VDDIO-0.45 max. 0.8 0.35*VDDIO 0.40 0.45 - unit V V V V V V V V 8. External LPO Specification Parameter Condition/Notes Frequency Frequency accuracy Duty cycle Input amplitude Signal type - Input impedancea Square wave or sine wave Resistive Capacitive Clock jitter a. When power is applied or switched off. Minimu m -200 30 200 100 - Specification Maximu Typical m 32.768 +200 70 3300 5 10,000 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Units KHz ppm % mV, p-p kΩ pF ppm Preliminary Specification Number : SP-KL1FX-G 10 / 29 9. Interface Timing 9.1. SDIO Timing (Default Mode) fPP tWL tWH CLK tTHL tISU tTLH tIH Input Output tODLY (max) tODLY (min) Parameter Symbol Min(1) Clock CLK (All values are referred to min. VIH and max. VIL(2) Frequency-Data Transfer Mode fPP 0 Frequency-Identification Mode fOD 0 Clock Low Time tWL 10 Clock High Time tWH 10 Clock Rise Time tTLH Clock Fall Time tTHL Inputs: CMD, DAT (referenced to CLK) Input Setup Time tISU 5 Input Hold Time tIH 5 Outputs: CMD, DAT (referenced to CLK) Output Delay time-Data Transfer Mode tODLY 0 Output Delay time-Identification Mode tODLY 0 Typ(1) Max(1) Unit - 25 400 10 10 MHz kHz ns ns ns ns - - ns ns - 14 50 ns ns (1). Timing is based on CL < 40pF load on CMD and Data. (2). Min (Vih) = 0.7*VDDIO and max (Vil) = 0.2*VDDIO. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 11 / 29 9.2. SDIO Timing (High Speed Mode) fPP tWL 50% VDD tWH CLK tTHL tISU tTLH tIH Input Output tODLY tOH Parameter Symbol Min(1) Clock CLK (All values are referred to min. VIH and max. VIL(2) Frequency-Data Transfer Mode fPP 0 Frequency-Identification Mode fOD 0 Clock Low Time tWL 7 Clock High Time tWH 7 Clock Rise Time tTLH Clock Fall Time tTHL Inputs: CMD, DAT (referenced to CLK) Input Setup Time tISU 6 Input Hold Time tIH 2 Outputs: CMD, DAT (referenced to CLK) Output Delay time-Data Transfer Mode tODLY Output Hold time tOH 2.5 Total System Capacitance (each line) CL - Typ(1) Max(1) Unit - 50 400 3 3 MHz kHz ns ns ns ns - - ns ns - 14 40 ns ns pF (1). Timing is based on CL < 40pF load on CMD and Data. (2). Min (Vih) = 0.7*VDDIO and max (Vil) = 0.2*VDDIO. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 12 / 29 10. DC/RF Characteristics 10.1. DC/RF Characteristics for IEEE802.11b Specification Mode Frequency Data rate IEEE802.11b DSSS / CCK 2400 - 2483.5MHz 1, 2, 5.5, 11Mbps Conditions : 25deg.C, VBAT=3.6V, VDDIO= 3.3V, Output power setting=17dBm, 11Mbps mode Items Contents - DC Characteristics min. typ. max. unit DC current 1) Tx mode (1024byte, 20usec interval) 320 370 mA 2) Rx mode 47 60 mA - Tx Characteristics min. typ. max. unit Output Power (tolerance) 15 17 19 dBm Spectrum Mask 1) 1st side lobes -43 -30 dBr 2) 2nd side lobes -54 -50 dBr Power-on and Power-down ramp 2.0 μsec RF Carrier Suppression 15 dB Modulation Accuracy (EVM) 15 35 % Outband Spurious Emissions 1) 30MHz to 1GHz (BW=100kHz) -36 dBm 2) 1GHz to 12.75GHz (BW=100kHz) -30 dBm 3) 1.8GHz to 1.9GHz (BW=100kHz) -47 dBm 4) 5.15GHz to 5.3GHz (BW=100kHz) -47 dBm - Rx Characteristics min. typ. max. unit Minimum Input Level (FER < 8%) -89 -76 dBm Maximum Input Level (FER < 8%) -10 dBm Adjacent Channel Rejection (FER < 8%) 35 dB Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 13 / 29 10.2. DC/RF Characteristics for IEEE802.11g Specification Mode Frequency Data rate IEEE802.11g OFDM 2400 - 2483.5MHz 6, 9, 12, 18, 24, 36, 48, 54Mbps Conditions : 25deg.C, VBAT=3.6V, VDDIO= 3.3V, Output power setting=13dBm, 54Mbps mode Items Contents - DC Characteristics min. typ. max. unit DC current 1) Tx mode (1024byte, 20usec interval) 270 310 mA 2) Rx mode 47 60 mA - Tx Characteristics min. typ. max. unit Output Power (tolerance) 11 13 15 dBm Spectrum Mask 1) 9MHz to 11MHz (0dB ~ -20dB) -33 -20 dBr 2) 11MHz to 20MHz (-20dB ~ -28dB) -41 -28 dBr 3) 20MHz to 30MHz (-28dB ~ -40dB) -53 -40 dBr 4) 30MHz to 33MHz (-40dB) -53 -40 dBr Constellation Error (EVM) -30 -25 dB Outband Spurious Emissions 1) 30MHz to 1GHz (BW=100kHz) -36 dBm 2) 1GHz to 12.75GHz (BW=100kHz) -30 dBm 3) 1.8GHz to 1.9GHz (BW=100kHz) -47 dBm 4) 5.15GHz to 5.3GHz (BW=100kHz) -47 dBm - Rx Characteristics min. typ. max. unit Minimum Input Level (PER < 10%) -75 -65 dBm Maximum Input Level (PER < 10%) -20 dBm Adjacent Channel Rejection (PER < 10%) -1 dB Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 14 / 29 10.3. DC/RF Characteristics for IEEE802.11n Specification Mode Frequency Data rate IEEE802.11n OFDM 2400 - 2483.5MHz 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps Conditions : 25deg.C, VBAT=3.6V, VDDIO= 3.3V, Output power setting=12dBm, 65Mbps mode Items Contents - DC Characteristics min. typ. max. unit DC current 1) Tx mode (1024byte, 20usec interval) 260 300 mA 2) Rx mode 47 60 mA - Tx Characteristics min. typ. max. unit Output Power (tolerance) 10 12 14 dBm Spectrum Mask 1) 9MHz to 11MHz (0dB ~ -20dB) -33 -20 dBr 2) 11MHz to 20MHz (-20dB ~ -28dB) -41 -28 dBr 3) 20MHz to 30MHz (-28dB ~ -45dB) -53 -45 dBr 4) 30MHz to 33MHz (-45dB) -53 -45 dBr Constellation Error (EVM) -31 -27 dB Outband Spurious Emissions 1) 30MHz to 1GHz -36 dBm 2) 1GHz to 12.75GHz -30 dBm 3) 1.8GHz to 1.9GHz -47 dBm 4) 5.15GHz to 5.3GHz -47 dBm - Rx Characteristics min. typ. max. unit Minimum Input Level (PER<10%) -73 -64 dBm Maximum Input Level (PER < 10%) -20 dBm Adjacent Channel Rejection (PER < 10%) -2 dB Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 15 / 29 11. Land pattern Top View. Unit : mm Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 16 / 29 12. Reference Circuit A B C D E F G H VIO 1 1 Antenna *1) LQM18PN2R2MGH recommended Antenna matching 2.2uF *2) GRM155R61A475MEAA recommended VIO 2 2 LPO_IN GND1 2 NC 3 NC 4 NC 5 6 7 10~100k 10~100k 10~100k 10~100k 10~100k 36 34 37 35 GND35 SR_VLX VIO 33 3 4.7uF *2) 32 VIN_LDO 31 VBAT VBAT 30 GND29 29 NC WL_REG_ON 28 NC WL_HOST_WAKE 27 NC SDIO_DATA_1 26 SDIO_DATA_1 8 NC SDIO_DATA_3 25 SDIO_DATA_3 9 NC SDIO_DATA_0 24 SDIO_DATA_2 23 SDIO_CMD 22 B GND21 WL_HOST_WAKE 4 SDIO_DATA_0 SDIO_DATA_2 SDIO_CMD 21 GND19 SDIO_CLK 20 19 WL_REG_ON SDIO_CLK WL_GPIO_1 WL_GPIO_2 17 18 WL_GPIO_1 WL_GPIO_2 NC 16 WL_GPIO_4 WL_GPIO_4 15 NC GND14 14 NC GND12 NC 11 12 10 TYPE1FX 5 A 4.7uF *2) GND(SR_PVSS) 13 4 1 2.2uH *1) GND(SR_PVSS) 3 LPO_IN(32KHZ) 40 39 38 NC NC 42 43 44 45 41 ANT GND40 GND42 GND43 GND44 GND45 GND46 46 GND(SR_PVSS) have to be isolated from typical GND C 5 D E F Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. G H Preliminary Specification Number : SP-KL1FX-G 17 / 29 13. Tape and Reel Packing 2.0±0.1 4.0±0.1 φ 1.5+0.1/-0.0 0.3±0.05 7.5±0.1 7.45±0.1 16.2±0.3 1.75±0.1 (1) Dimensions of Tape (Plastic tape) φ 1.5±0.1 8.0±0.1 5.55±0.1 1.8 max. (1.7±0.1) feeding direction The corner and ridge radiuses (R) of inside cavity are 0.3mm max. Cumulative tolerance of 10 pitches of the sprocket hole is +/-0.2mm Measuring of cavity positioning is based on cavity center in accordance with JIS/IES standard. (2) Dimensions of Reel 17.5 (Φ330) 2±0.5 (Φ100) 1) 2) 3) Φ13±2 22.5 max. (unit : mm) Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 18 / 29 (3) Taping Diagrams [1] Feeding Hole : As specified in (1) [2] Hole for chip : As specified in (1) [3] Cover tape : 62μm in thickness [4] Base tape : As specified in (1) Feeding Hole Feeding Direction Pin 1 Marking Chip (4) Leader and Tail tape Feeding direction Tail tape (No components) 40 to 200mm Components No components Leader tape (Cover tape alone) 150mm min. 250mm min. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 19 / 29 (5) The tape for chips are wound clockwise, the feeding holes to the right side as the tape is pulled toward the user. (6) The cover tape and base tape are not adhered at no components area for 250mm min. (7) Tear off strength against pulling of cover tape : 5N min. (8) Packaging unit : 1000pcs./ reel (9) material : Base tape : Plastic Real : Plastic Cover tape, cavity tape and reel are made the anti-static processing. (10) Peeling of force : 1.1N max. in the direction of peeling as shown below. 1.1N max. 165 to 180 ° Cover tape Base tape (11) Packaging (Humidity proof Packing) Label 表示ラべル Desiccant 乾燥剤 Humidity 湿度 Indicator インジケ－タ 表示ラベル Label 防湿梱包袋 Anti-humidity Plastic Bag Tape and reel must be sealed with the anti-humidity plastic bag. The bag contains the desiccant and the humidity indicator. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 20 / 29 14. NOTICE 14.1. Storage Conditions: Please use this product within 6month after receipt. - The product shall be stored without opening the packing under the ambient temperature from 5 to 35deg.C and humidity from 20 to 70%RH. (Packing materials, in particular, may be deformed at the temperature over 40deg.C.) - The product left more than 6months after reception, it needs to be confirmed the solderbility before used. - The product shall be stored in non corrosive gas (Cl2, NH3, SO2, NOx, etc.). - Any excess mechanical shock including, but not limited to, sticking the packing materials by sharp object and dropping the product, shall not be applied in order not to damage the packing materials. This product is applicable to MSL3 (Based on JEDEC Standard J-STD-020) - After the packing opened, the product shall be stored at <30deg.C / <60%RH and the product shall be used within 168hours. - When the color of the indicator in the packing changed, the product shall be baked before soldering. Baking condition: 125+5/-0deg.C, 24hours, 1time The products shall be baked on the heat-resistant tray because the material (Base Tape, Reel Tape and Cover Tape) are not heat-resistant. 14.2. Handling Conditions: Be careful in handling or transporting products because excessive stress or mechanical shock may break products. Handle with care if products may have cracks or damages on their terminals, the characteristics of products may change. Do not touch products with bear hands that may result in poor solder ability and destroy by static electrical charge. 14.3. Standard PCB Design (Land Pattern and Dimensions): All the ground terminals should be connected to the ground patterns. Furthermore, the ground pattern should be provided between IN and OUT terminals. Please refer to the specifications for the standard land dimensions. The recommended land pattern and dimensions is as Murata's standard. The characteristics of products may vary depending on the pattern drawing method, grounding method, land dimensions, land forming method of the NC terminals and the PCB material and thickness. Therefore, be sure to verify the characteristics in the actual set. When using non-standard lands, contact Murata beforehand. 14.4. Notice for Chip Placer: When placing products on the PCB, products may be stressed and broken by uneven forces from a worn-out chucking locating claw or a suction nozzle. To prevent products from damages, be sure to follow the specifications for the maintenance of the chip placer being used. For the positioning of products on the PCB, be aware that mechanical chucking may damage products. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 21 / 29 14.5. Soldering Conditions: The recommendation conditions of soldering are as in the following figure. When products are immersed in solvent after mounting, pay special attention to maintain the temperature difference within 100 °C. Soldering must be carried out by the above mentioned conditions to prevent products from damage. Set up the highest temperature of reflow within 260 °C. Contact Murata before use if concerning other soldering conditions. Reflow soldering standard conditions (Example) Within 3s 240to 250 deg.C 220 deg.C Cooling down Slowly 180 deg.C 150 deg.C Pre-heating Within 120s Within 60s time(s) Please use the reflow within 2 times. Use rosin type flux or weakly active flux with a chlorine content of 0.2 wt % or less. 14.6. Cleaning: Since this Product is Moisture Sensitive, any cleaning is not permitted. 14.7. Operational Environment Conditions: Products are designed to work for electronic products under normal environmental conditions (ambient temperature, humidity and pressure). Therefore, products have no problems to be used under the similar conditions to the above-mentioned. However, if products are used under the following circumstances, it may damage products and leakage of electricity and abnormal temperature may occur. - In an atmosphere containing corrosive gas (Cl2, NH3, SOx, NOx, etc.). - In an atmosphere containing combustible and volatile gases. - Dusty place. - Direct sunlight place. - Water splashing place. - Humid place where water condenses. - Freezing place. If there are possibilities for products to be used under the preceding clause, consult with Murata before actual use. As it might be a cause of degradation or destruction to apply static electricity to products, do not apply static electricity or excessive voltage while assembling and measuring. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 22 / 29 14.8. Input Power Capacity: Products shall be used in the input power capacity as specified in this specifications. Inform Murata beforehand, in case that the components are used beyond such input power capacity range. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 23 / 29 15. PRECONDITION TO USE OUR PRODUCTS PLEASE READ THIS NOTICE BEFORE USING OUR PRODUCTS. Please make sure that your product has been evaluated and confirmed from the aspect of the fitness for the specifications of our product when our product is mounted to your product. All the items and parameters in this product specification/datasheet/catalog have been prescribed on the premise that our product is used for the purpose, under the condition and in the environment specified in this specification. You are requested not to use our product deviating from the condition and the environment specified in this specification. Please note that the only warranty that we provide regarding the products is its conformance to the specifications provided herein. Accordingly, we shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this specification. WE HEREBY DISCLAIMS ALL OTHER WARRANTIES REGARDING THE PRODUCTS, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, THAT THEY ARE DEFECT-FREE, OR AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. The product shall not be used in any application listed below which requires especially high reliability for the prevention of such defect as may directly cause damage to the third party's life, body or property. You acknowledge and agree that, if you use our products in such applications, we will not be responsible for any failure to meet such requirements. Furthermore, YOU AGREE TO INDEMNIFY AND DEFEND US AND OUR AFFILIATES AGAINST ALL CLAIMS, DAMAGES, COSTS, AND EXPENSES THAT MAY BE INCURRED, INCLUDING WITHOUT LIMITATION, ATTORNEY FEES AND COSTS, DUE TO THE USE OF OUR PRODUCTS IN SUCH APPLICATIONS. - Aircraft equipment. - Aerospace equipment - Undersea equipment. - Power plant control equipment - Medical equipment. - Transportation equipment (vehicles, trains, ships, elevator, etc.). - Traffic signal equipment. - Disaster prevention / crime prevention equipment. -Burning / explosion control equipment - Application of similar complexity and/ or reliability requirements to the applications listed in the above. We expressly prohibit you from analyzing, breaking, reverse-engineering, remodeling altering, and reproducing our product. Our product cannot be used for the product which is prohibited from being manufactured, used, and sold by the regulations and laws in the world. We do not warrant or represent that any license, either express or implied, is granted under any our patent right, copyright, mask work right, or our other intellectual property right relating to any combination, machine, or process in which our products or services are used. Information provided by us regarding third-party products or services does not constitute a license from us to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from us under our patents or other intellectual property. Please do not use our products, our technical information and other data provided by us for the purpose of developing of mass-destruction weapons and the purpose of military use. Moreover, you must comply with "foreign exchange and foreign trade law", the "U.S. export administration regulations", etc. Please note that we may discontinue the manufacture of our products, due to reasons such as end of supply of materials and/or components from our suppliers. By signing on specification sheet or approval sheet, you acknowledge that you are the legal representative for your company and that you understand and accept the validity of the contents herein. When you are not able to return the signed version of specification sheet or approval sheet within 30 days from receiving date of specification sheet or approval sheet, it shall be deemed to be your consent on the content of specification sheet or approval sheet. Customer acknowledges that engineering samples may deviate from specifications and may contain defects due to their development status. We reject any liability or product warranty for engineering samples. In particular we disclaim liability for damages caused by - the use of the engineering sample other than for evaluation purposes, particularly the installation or integration in the product to be sold by you, -deviation or lapse in function of engineering sample, -improper use of engineering samples. We disclaim any liability for consequential and incidental damages. If you can’t agree the above contents, you should inquire our sales. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 24 / 29 APPENDIX Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 25 / 29 1DX Installation Manual (FCC) FCC ID of this product is as follows. FCC ID:VPYLB1DX For OEM integration only – device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by FCC on the product and in the Installation manual Notice. Contents 1. Antenna 2. Notice 1. Antenna ■Please perform the antenna design that followed the specifications of the antenna. The concrete contents of a check are the following three points. 1) It is the same type as the antenna type of antenna specifications. Confirm the same size as the Gerber file. 2) An antenna gain is lower than a gain given in antenna specifications. Measure the gain, and confirm the peak gain is less than the application value (1.4dBi) 3) The emission level is not getting worse. Measure the spurious, and confirm degradation of less than 3dB than spurious value of worst of report used for the application. However it is spurious defined below. Please send those reports to Murata. 2. Notice For OEM integration only – device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by FCC/IC on the product and in the Installation manual Notice. Please describe the following warning on the final product which contains this module. Contains Transmitter Module FCC ID:VPYLB1DX or Contains FCC ID:VPYLB1DX ●Please describe the following warning to the manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. ※When the product is small, as for these words mentioned above, the posting to a manual is possible. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 26 / 29 ●When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. RF Exposure requirements are met when installed in mobile equipment. This module cannot be installed in portable equipment without further testing and a change to FCC's grant of authorization. Contact Murata regarding portable applications. Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. This device is intended only for OEM integrators under the following conditions: 1)The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2)The transmitter module may not be co-located with any other transmitter or antenna. 3)The use of an antenna with gain less than 1.4 dBi. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID:XXXXXXXXXX”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 27 / 29 1DX Installation Manual (IC) IC No. of this product is as follows. IC : 772C-LB1DX For OEM integration only – device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by IC on the product and in the Installation manual Notice. Contents 1. Antenna 2. Notice 1. Antenna ■Please perform the antenna design that followed the specifications of the antenna. The concrete contents of a check are the following three points. １）It is the same type as the antenna type of antenna specifications. Confirm the same size as the Gerber file. ２）An antenna gain is lower than a gain given in antenna specifications. Measure the gain, and confirm the peak gain is less than the application value (1.4dBi) ３）The emission level is not getting worse. Measure the spurious, and confirm degradation of less than 3dB than spurious value of worst of report used for the application. However it is spurious defined below. Please send those reports to Murata. 2. Notice For OEM integration only – device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by FCC/IC on the product and in the Installation manual Notice. Please describe the following warning on the final product which contains this module. Contains IC:772C-LB1DX This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. ※When the product is small, as for these words mentioned above, the posting to a manual is possible Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 28 / 29 ●When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. RF Exposure requirements are met when installed in mobile equipment. This module cannot be installed in portable equipment without further testing and a change to FCC's grant of authorization. Contact Murata regarding portable applications. Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. 3)The use of an antenna with gain less than 1.4 dBi. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1)L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2)Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 3 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-KL1FX-G 29 / 29 IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: ”. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: ". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd.