DCDC 6 Watts JTE Series xppower.com • 4:1 Input Range • DIP24 Plastic Case • Operating Temperature 40 °C to +100 °C • Single & Dual Outputs • Optional Metal Case • 1500 VDC Isolation, 3000 VDC Option • 3 Year Warranty Specification Input General • 24 V (9-36 VDC) 48 V (18-75 VDC) Input Current • See table Input Filter • Pi network Input Reflected Ripple • 20 mA pk-pk through 12 µH inductor and 4.7 µF capacitor Input Surge • 24 V models 50 VDC for 100 ms 48 V models 100 VDC for 100 ms Under Voltage Lockout • 24 V models on >8.5 V, off <8.0 V 48 V models on >16.5 V, off <15.5 V Input Voltage Range Isolation Capacitance • See table • 1500 VDC Input to Output, for optional high isolation version 3000 VDC input to output add suffix ‘-H’ to model number 1000 VDC Input to Case 1000 VDC Output to Case • 1000 pF typical input to output Isolation Resistance Switching Frequency Power Density MTBF • • • • Efficiency Isolation Voltage Output Output Voltage Output Voltage Balance Initial Set Accuracy Minimum Load Line Regulation Load Regulation • • • • • • Cross Regulation • Start Up Delay Ripple & Noise • • Transient Response • Overload Protection • Short Circuit Protection • Maximum Capacitive Load Temperature Coefficient • See table ±2% max, dual output models ±2% max No minimum load required ±0.5% max ±1.2% max for single output and ±5% max for dual output from 10-100% ±5% max on dual output models (see note 4) 20 ms typical 80 mV pk-pk (100 mV for D24 models), 20 MHz bandwidth (see note 5) <3% max deviation, recovery to within 1% in 300 µs for a 25% load change (4% max. deviation for S3V3 models) 135% - 185% of Full Load Trip & restart (Hiccup mode), auto recovery See table 109Ω 330 kHz typical 15 W/in3 >800 kHrs to MIL-HDBK-217F at 25 °C, GB Environmental Operating Temperature • -40 °C to +100 °C, derate from 100% load at +60 °C to no load at +100 °C Case Temperature • +100 °C max Storage Temperature • -55 °C to +125 °C Cooling • Natural convection Operating Humidity • Up to 95%, non-condensing EMC Emissions ESD Immunity Radiated immunity EFT/Burst Surge Conducted Immunity Magnetic Fields • EN55022 class A conducted • EN61000-4-2, Level 3 8 kV air discharge Perf Criteria B, 6 kV contact discharge Perf Criteria B • EN61000-4-3, 10 V/m, Perf Criteria A • EN61000-4-4, level 3, Perf Criteria A* • EN61000-4-5, level 2, Perf Criteria A* • EN61000-4-6, 10 Vrms, Perf Criteria A • EN61000-4-8, 1 A/m, Perf Criteria A • ±0.02/°C max * External input capacitor required, 220µF/100V Input Voltage Output Voltage 3.3 5.0 12.0 15.0 24.0 ±3.3 ±5.0 ±12.0 ±15.0 ±24.0 3.3 5.0 12.0 15.0 24.0 ±3.3 ±5.0 ±12.0 ±15.0 ±24.0 9-36 V 18-75 V V V V V V V V V V V V V V V V V V V V V Input Current(2) No Load Full Load Output Current 1400 1200 500 400 250 ±909 ±600 ±250 ±200 ±125 1400 1200 500 400 250 ±909 ±600 ±250 ±200 ±125 mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA 10 mA 10 mA 10 mA 10 mA 10 mA 10 mA 10 mA 10 mA 15 mA 20 mA 7 mA 7 mA 7 mA 7 mA 7 mA 7 mA 7 mA 7 mA 7 mA 10 mA 257 316 301 301 301 324 308 301 301 308 128 154 151 151 151 162 154 151 151 158 Maximum Capacitive Load(3) Efficiency Model Number(1,6) 470 470 100 100 47 ±220 ±220 ±100 ±100 ±47 470 470 100 100 47 ±220 ±220 ±100 ±100 ±47 76% 80% 84% 84% 84% 78% 82% 84% 84% 82% 76% 82% 84% 84% 84% 78% 82% 84% 84% 80% JTE0624S3V3 JTE0624S05 JTE0624S12 JTE0624S15 JTE0624S24 JTE0624D03 JTE0624D05 JTE0624D12 JTE0624D15 JTE0624D24 JTE0648S3V3 JTE0648S05 JTE0648S12 JTE0648S15 JTE0648S24 JTE0648D03 JTE0648D05 JTE0648D12 JTE0648D15 JTE0648D24 mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA µF µF µF µF µF µF µF µF µF µF µF µF µF µF µF µF µF µF µF µF Notes 1. For optional 3000 VDC isolation add suffix ‘-H’ to model number. 2. Input current measured at nominal input voltage. 3. Maximum capacitive load is per output. 4. Cross regulation for duals is ±5% when one output is at 100% and the other is varied between 25% and 100%. 5. Ripple & Noise measured with 1µF ceramic capacitor across output pins. 6. For optional metal case version, add suffix ‘-M’ to part number e.g. JTE0624S12-M. Mechanical Details Plastic Case Optional Metal Case 1.25 (31.75) DIA 0.02 (0.50) 1.25 (31.75) Printed Face 2 0.40 (10.40) 0.80 (20.32) 0.80 (20.32) 9 2 3 11 0.60 (15.24) Bottom View 23 22 16 14 0.02 (0.50) 0.20 (5.08) Pin 2 3 9 11 14 16 22 23 Single -Vin -Vin No Pin N.C. +Vout -Vout +Vin +Vin Dual -Vin -Vin Common -Vout +Vout Common +Vin +Vin Notes 1. All dimensions are in inches (mm) 2. Weight: 0.04 lbs (17 g) approx. 3. Pin diameter: 0.02 ±0.002 (0.5 ±0.005) 9 16 22 0.10 (2.54) Printed Face 0.90 (22.86) 3 11 0.60 (15.24) Bottom View 23 0.12 (3.05) 0.02 (0.50) 0.90 (22.86) 14 0.20 (5.08) 0.40 (10.40) 0.12 (3.05) Min. 4. Pin pitch tolerance: ±0.014 (0.35) 5. Case tolerance: ±0.02 (±0.5) Application Note 100 80 Load (%) Derating Curve 60 40 20 0 -40 -20 0 10 20 30 40 50 60 Ambient Temperature (ºC) 70 80 90 100 02-Aug-13 DCDC JTE06 Models and Ratings