EDI BRUS220F Ultra-fast recovery single-phase, full-wave bridges heat sink chassis p.c. board mounting Datasheet

BRUS2 BRUS2F
MINIBRIDGE
50 ns. ULTRA-FAST RECOVERY
SINGLE-PHASE, FULL-WAVE BRIDGES
HEAT SINK CHASSIS P.C. BOARD MOUNTING
e
on
mp
o
ec
r th inc.
e
d
un ies,
ion ator
t
i
r
n
og bo
ec s La
r
tes iter
ica erwr
d
in nd
ark of U
m
is m
Th ogra
pr
BRUS 2F
10.5 Amps. Quick-connects
BRUS2
9 Amps. Wire Leads
PRV/Leg
nt
50V
100V
200V
400V
600V
9.0 AMP SERIES
BRUS205
BRUS210
BRUS220
BRUS240
BRUS260
10.5AMP SERIES
BRUS205F
BRUS210F
BRUS220F
BRUS240F
BRUS260F
ELECTRICAL CHARACTERISTICS PER LEG
(at TA =25 C U nle ss O the rwis e Sp eci fie d)
BRUS2
BRUS2F
UNITS
9.0
10.5
Amps
Max. Forward Voltage Drop, VF@ IF= 2.0
1.3
1.3
Volts
Max.DC Reverse Current @ PRV and 25 C ,IR
10
10
A
Max.DC Reverse Current @ PRV and 100 C ,IR
200
200
A
Max. Reverse Recovery Time,Trr (Fig.4)
50
50
Nanosec.
Max. Peak Surge Current, l FSM (8.3ms)
125
125
Amps
O
Average Output Current l F (Av.) TC 60 C (Fig.1)
Storage Temperature Range, TSTG
Thermal Resistance (Total Bridge), R0- j -c
,
o
-55 to+150
5.5 typ.
4.5 typ.
C
o
C/W
EDI reserves the right to change these specifications at any time without notice.
BRUS2 BRUS2F
FIG.2
NON-REPETITIVE SURGE CURRENT
FIG.1
CURRENT DERATING
1000
BRUS2F
500
8
PEAK SURGE CURRENT I FSM
10
BRUS2
6
4
2
200
100
50
20
(AMP)
L
l F(AV). AVERAGE FORWARD CURRENT
12
0
0
25
75
50
10
100
125
150
1
5
2
10
20
50
100
NUMBER OF CYCLES AT 60 Hz
O
TC=TEMPERATURE( C)
FIG.3
TEST CIRCUIT
T RR
R1
50 OHM
ZERO
REFERENCE
0.5A
D.U.T.
+
R1, R2 NON-INDUCTIVE RESISTORS
PULSE GENERATOR - HEWLETT
PACKARD 214A OR EQUIV.
IKC REP.RATE, 10 SEC. PULSE WIDTH
ADJUST PULSE AMPLITUDE FOR PEAK IR
-
1.0A
0.25A
PULSE
GENERATOR
R2
1 OHM
SCOPE
BRUS2-F SERIES MECH. OUTLINE
BRUS2 SERIES MECH. OUTLINE
Dielectric test voltage 1500 volts rms, max. 50-60Hz
+ .002 DIA.
.040 _
.150 DIA
THRU.
FASTON
4 PLACES
THRU
.50 MAX.
+
AC
1 MIN.
AC
+
+
AC
AC
.30 MAX.
EPOXY
.85 MAX.
_ .015
.463 +
_
.30 MAX.
_ .015
.463 +
METAL BASE
.85MAX.
EPOXY
METAL BASE
NOTE: A thin film of silicone thermal compound is recommended between the Minibridge
case and mounting surface for improved thermal conduction.
ELECTRONIC DEVICES, INC. DESIGNERS AND MANUFACTURERS OF SOLID STATE DEVICES SINCE 1951.
21 GRAY OAKS AVENUE
* YONKERS. NEW YORK 10710 914-965-4400
Ee-mail:[email protected]:
*
http://www.edidiodes.com
* FAX 914-965-5531
* 1-800-678-0828
Similar pages