Low Signal Relay
G6K
• Compact fourth generation design, offers excellent board
space savings.
• Available in 2.54 and 3.2 mm coil-contact terminal spacing.
• “-Y” models meet 2.5 kV Bellcore surge requirements.
• Conforms to FCC Part 68.
• Terminal design based on Omron’s successful G6S relay.
• Available in PCB through-hole, SMT gullwing and SMT
“inside-L” terminals.
• UL recognized / CSA certified.
• Available in single coil latching.
• RoHS Compliant.
RC
Ordering Information
To Order: Select the part number and add the desired coil voltage rating (e.g., G6K-2F-DC5).
Terminal
Contact form
Model
Non-latching
2.54 mm spacing
Gullwing
DPDT
Non-latching
3.2 mm coil-contact
terminal spacing
Single coil latching
3.2 mm coil-contact
terminal spacing
G6K-2F
G6K-2F-Y
G6KU-2F-Y
Inside “L”
G6K-2G
G6K-2G-Y
G6KU-2G-Y
PCB through-hole
G6K-2P
G6K-2P-Y
G6KU-2P-Y
When ordering tape packing (surface mount versions), add “-TR” to the model number (e.g., G6K-2G-TR-DC5)
Specifications
■ Contact Data
Load
Resistive load (cosφ=1)
Rated load
0.3 A at 125 VAC
1 A at 30 VDC
Contact material
Ag (Au clad)
Max. carry current
1A
Max. operating voltage
125 VAC, 60 VDC
Max. operating current
1A
Max. switching capacity
37.5 VA, 30W
Min. permissible load (See note)
10 μA at 10 mVDC
Note: This value was measured at a switching frequency of 120 operations/min and the criterion of contact resistance is 50 Ω. This value may vary
depending on the switching frequency and operating environment. Always double-check relay suitability under actual operating conditions.
Low Signal Relay
G6K
67
■ Coil Data
G6K- 2.5 mm coil-contact terminal spacing, standard, non-latching (G6K-2F, G6K-2G, G6K-2P)
G6K- 3.2 mm coil-contact terminal spacing, non-latching (G6K-2F-Y, G6K-2G-Y, G6K-2P-Y)
Rated voltage
(VDC)
Rated current
(mA)
Coil resistance
(Ω)
3
33.0
91
4.5
23.2
194
5
21.1
237
6
17.6
341
9
11.3
795
12
9.1
1,315
24
4.6
5,220
Pick-up voltage
Dropout voltage
Maximum voltage
% of rated value
80% max.
10% min.
150% max.
@ 23°C to 70°C
Power consumption
(mW)
Approx. 100
G6KU- 3.2 mm spacing, single coil latching (G6KU-2F-Y, G6KU-2G-Y, G6KU-2P-Y)
Rated voltage
(VDC)
Rated current
(mA)
Coil resistance
(Ω)
3
33.0
91
4.5
23.2
194
5
21.1
237
6
17.6
341
9
11.3
795
12
9.1
1,315
24
4.6
5,220
Note: 1.
2.
3.
4.
Set-up voltage
Reset voltage
Maximum voltage
% of rated value
75% max.
75% min.
150% max.
@ 23°C to 70°C
Power consumption
(mW)
Approx. 100
The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ± 10%.
The operating characteristics are measured at a coil temperature of 23°C unless otherwise specified.
Pick-up voltage will vary with temperature
The maximum voltage is the highest voltage that can be imposed on the relay coil instantaneously.
■ Characteristics
Contact resistance (See note 1)
100 mΩ max.
Operate (set) time (See note 2)
3 ms max. (Approx. 1.4 ms - standard. Approx. 1.2 ms - latching)
Release (set) time (See note 2)
3 ms max. (Approx. 1.3 ms - standard. Approx. 1.2 ms - latching)
Insulation resistance (See note 3)
1,000 MΩ min. (at 500 VDC)
Dielectric strength
1,500 VAC for 1 minute between coil contacts
1,000 VAC for 1 minute between contacts of different poles
750 VAC for 1 minute between contacts of the same pole
Surge withstand voltage “-Y’ versions
2,500 V, (2 x 10 μs) between coil and contacts.
(Conforms to Bellcore specifications)
Standard versions
1,500 V, (10 x 160 μs) between coil and contacts / contacts of different and same polarity.
(Conforms to FCC Part 68)
Vibration
Mechanical durability 10 to 55 Hz; 5.0 mm double amplitude
Shock
Mechanical durability 1,000 m/s2 (approx. 100G)
Malfunction durability 10 to 55 Hz; 3.3 mm double amplitude
Malfunction durability 750 m/s2 (approx. 75G)
Ambient temperature
-40°C to 70°C with no icing or condensation
Humidity
Service life
5 to 85% RH
Mechanical
50,000,000 operations min. (at 36,000 operations per hour)
Electrical
100,000 operations min. at rated load (at 1,800 operations per hour)
Weight
Note: 1.
2.
3.
4.
68
Approx. 0.7 g
The contact resistance was measured with 10 mA at 1 VDC with a voltage-drop method.
Values in parentheses are typical values unless otherwise stated.
The insulation resistance was measured with a 500-VDC megohmmeter applied to the same parts as those for checking the dielectric strength.
Data shown are of initial value.
Low Signal Relay
G6K
■ Characteristic data
DC resistive load
Ambient Temperature vs.
Switching Current
Rated operating current (A)
AC resistive load
Ambient Temperature vs.
Maximum Coil Voltage
Maximum coil voltage (%)
Rated operating current (A)
Maximum Switching Capacity
Ambient temperature (°C)
Ambient temperature (°C)
Rated operating voltage (V)
Note: The maximum coil voltage refers to the maximum value in a varying range of operating
power voltage, not a continuous voltage.
Ambient Temperature vs. Must
Ambient Temperature vs. Must
Operate or Must Release Voltage Set or Must Reset Voltage
G6KU-2G (F/P)-Y
125 VAC resistive load
Ambient temperature: 23°C
Switching frequency:
1,800 operations/hour
Not
energized
Shock direction
Conditions:
Unit: m/s 2
Sample: G6K-2G
Number of Relays: 10
Shock is applied in ±X, ±Y, and ±Z di
rections three times each with and with
out energizing the Relays to check the
number of contact malfunctions.
Electrical Service Life
(with Must Operate and Must
Release Voltage) (See note.)
G6K-2G (F/P), G6K-2G (F/P)-Y
On the basis of rated voltage (%)
Energized
Operate voltage
Release voltage
Ambient temperature (°C)
Rated operating current (A)
Shock Malfunction
Max. estimated value
Sample: G6K-2G
Number of Relays: 10
Test conditions: 1 A resistive load at
30 VDC with an operation rate of 50%
Switching frequency: 1,800 operations/h
Must operate
Max. estimated value
Ambient temperature (°C)
Electrical Service Life
(Contact Resistance) (See note.)
G6K-2G (F/P), G6K-2G (F/P)-Y
Contact resistance (mΩ)
30 VDC resistive load
Ambient temperature: 23°C
Switching frequency:
1,800 operations/hour
On the basis of rated voltage (%)
Service Life (x104 operations)
G6K-2G (F/P), G6K-2G (F/P)-Y
On the basis of rated voltage (%)
Electrical Service Life
Sample: G6K-2G
Number of Relays: 10
Test conditions: 1 A resistive load
at 30 VDC with an operation rate of 50%
Switching frequency: 1,800 operations/h
NO
contact
NC
contact
Contact resistance
Must release
Operating frequency (x10 3 operations)
Operating frequency (x103 operations)
Note: The tests were conducted at an
ambient temperature of 23°C.
Note: The tests were conducted at an
ambient temperature of 23°C.
Low Signal Relay
G6K
69
Contact Reliability Test (See note.)
Mutual Magnetic Interference Mutual Magnetic Interference
G6K-2G (F/P), G6K-2G (F/P)-Y
G6K-2G (F/P), G6K-2G (F/P)-Y
G6K-2G (F/P), G6K-2G (F/P)-Y
Not energized
Sample
Energized
Initial stage
Test
Sample
Not energized
Average value
Test
Sample
Energized
Average value
Change rate on the basis
of initial value (%)
Sample
Initial stage
Must operate voltage
Must release voltage
Initial stage
Change rate on the basis
of initial value (%)
NO
contact
NC
contact
Change rate on the basis
of initial value (%)
Contact resistance (m Ω)
Sample: G6K-2G
Number of Relays: 10
Test conditions: 10 mA resistive load at
10 mVDC with an operation rate of 50 %
Switching frequency: 7,200 operations/h
Change rate on the basis
of initial value (%)
Must operate voltage
Must release voltage
Test
Average value
Initial stage
Test
Average value
3
Operating frequency (x10 operations)
Note 1: The test was conducted at an ambient temperature of 23°C.
2: The contact resistance data are periodically measured reference values and are not values from each monitoring operation.
Contact resistance values will vary according to the switching frequency and operating environment, so be sure to check
operation under the actual operating conditions before use.
(Average value)
Sample: G6K-2G
Number of Relays: 10
Must operate voltage
Must release voltage
External magnetic field (A/m)
(Average value)
Sample: G6K-2G
Number of Relays: 10
Must operate voltage
Must release voltage
External magnetic field (A/m)
Change rate on the basis of initial value (%)
G6K-2G (F/P), G6K-2G (F/P)-Y
Change rate on the basis of initial value (%)
Change rate on the basis of initial value (%)
External Magnetic Interference
(Average value)
Sample: G6K-2G
Number of Relays: 10
Must operate voltage
Must release voltage
External magnetic field (A/m)
High-frequency Characteristics
(Isolation)
G6K-2G (F/P), G6K-2G (F/P)-Y
(Insertion Loss)
G6K-2G (F/P), G6K-2G (F/P)-Y
(Return Loss)
G6K-2G (F/P),G6K-2G (F/P)-Y
10
Sample: G6K-2G
Number of Relays: 10
20
30
40
50
0.1
0.2
0.3
60
70
0
1.4
Sample: G6K-2G
Number of Relays: 10
10
1.35
20
1.3
30
1.25
Return loss
40
1.2
50
1.15
60
1.1
0.4
80
10
100
Frequency (MHz)
0.5
1
10
1.05
70
Sample: G6K-2G
Number of Relays: 10
90
100
1
(Average value)
(Average value)
0
Return loss (dB)
Isolation (dB)
(Average value)
0
V.SWR
1
80
100
Frequency (MHz)
1
10
100
Frequency (MHz)
Note: 1. The tests were conducted at an ambient temperature of 23°C.
2. High-frequency characteristics depend on the PCB to which the Relay is mounted. Always check these characteristics including
endurance in the actual machine before use.
70
V.SWR
High-frequency Characteristics
Insertion loss (dB)
High-frequency Characteristics
Low Signal Relay
G6K
Must Operate and Must Release
Time Distribution (See note.)
Must Operate and Must Release
Bounce Time Distribution (See note.)
Vibration Resistance
G6K-2G (F/P), G6K-2G (F/P)-Y
G6K-2G (F/P), G6K-2G (F/P)-Y
G6K-2G (F/P) , G6K-2G (F/P)-Y
Number of contacts
Number of contacts
Change rate on the basis of rated value (%)
Sample: G6K-2G
Number of Relays:
50
Must operate
Must release time
Must operate
bounce time
Must release
bounce time
Sample: G6K-2G
Number of Relays: 50
Time (ms)
Time (ms)
Note: The tests were conducted at an ambient temperature of 23°C.
Must operate voltage
Must release voltage
After test
■ Approvals
UL Recognized (File No. E41515) / CSA Certified (File No. LR31928) - - Ambient Temp. = 40°C
Contact form
DPDT
Coil rating
Contact ratings
3 to 24 VDC
1 A at 30 VDC (Resistive)
0.5 A at 60 VDC (Resistive)
0.3 A at 125 VAC (General Use)
Number of test operations
6,000
Dimensions
Note: All units are in millimeters unless otherwise indicated.
G6K-2F
Mounting Dimensions (Top View)
Tolerance: ±0.1 mm
Orientation mark
Note: Each value has a tolerance of ±0.3 mm.
G6K-2G
Terminal Arrangement/
Internal Connections
(Top View)
Mounting Dimensions (Top View)
Tolerance: ±0.1 mm
Terminal Arrangement/
Internal Connections
(Top View)
Orientation mark
Note: Each value has a tolerance of ±0.3 mm.
G6K-2P
Mounting Dimensions (Bottom View) Terminal Arrangement/
Tolerance: ±0.1 mm
Internal Connections
(Bottom View)
Eight, 0.8-dia. holes
Orientation mark
Note: Each value has a tolerance of ±0.3 mm.
Low Signal Relay
G6K
71
Mounting Dimensions (Top View)
Tolerance: ±0.1 mm
G6K-2F-Y
Orientation mark
Note: Each value has a tolerance of ±0.3 mm.
Mounting Dimensions (Top View)
Tolerance: ±0.1 mm
G6K-2G-Y
Terminal Arrangement/
Internal Connections
(Top View)
Orientation mark
Note: Each value has a tolerance of ±0.3 mm.
Mounting Dimensions (Bottom View)
Tolerance: ±0.1 mm
G6K-2P-Y
Terminal Arrangement/
Internal Connections
(Top View)
Eight,
0.8-dia. holes
Terminal Arrangement/
Internal Connections
(Bottom View)
Orientation mark
Note: Each value has a tolerance of ±0.3 mm.
Mounting Dimensions (Top View)
Tolerance: ±0.1 mm
G6KU-2F-Y
Orientation mark
Note: Each value has a tolerance of ±0.3 mm.
Mounting Dimensions (Top View)
Tolerance: ±0.1 mm
G6KU-2G-Y
Note: Each value has a tolerance of ±0.3 mm.
G6KU-2P-Y
Terminal Arrangement/
Internal Connections
(Top View)
Terminal Arrangement/
Internal Connections
(Top View)
Orientation mark
Mounting Dimensions (Bottom View) Terminal Arrangement/
Internal Connections
Tolerance: ±0.1 mm
Eight, 0.8-dia. holes
(Bottom View)
Orientation mark
Note: Each value has a tolerance of ±0.3 mm.
72
Low Signal Relay
G6K
■ Packaging Information
Tube packing
Standard nomenclature
50 pcs per anti-static tube
Tape packing
When ordering, add “TR” before the rated coil voltage (e.g., G6K-2G-TR-DC5).
(SMT versions, only) Note: TR is not part of the relay model number and will not be marked on the relay.
900 pcs per reel
2 reels per box
Order in box multiples
(see details below)
Relays in tube packing are arranged so that the orientation mark of each Relay is on the left side.
Be sure to reference Relay orientation when mounting the Relay to the PCB.
Stopper (gray)
Orientation of Relays
Stopper (green)
Tube length: 520 mm (stopper not included)
No. of Relays per Tube: 50
■ Tape and Reel Dimensions (Surface Mount Models)
• Tape type: ETX7200 (EIAJ - Electronic Industrial Association of Japan)
• Reel type: RPM-16D (EIAJ, 330 mm diameter)
• Relays per reel: 900
3. Carrier Tape Dimensions
1. Direction of Relay Insertion
Top tape
(cover tape)
G6K-2F, G6K-2F-Y, G6KU-2F-Y
Orientation mark
Pulling
direction
Carrier tape
2. Reel Dimensions
Emboss
tape
G6K-2G, G6K-2G-Y, G6KU-2G-Y
Low Signal Relay
G6K
73
■ Recommended Soldering Method
Temperature indicates the surface temperature of the PCBs.
IRS Method (for surface mounting terminal models)
(2) IRS Method (Mounting Solder: Lead-free)
Temperature (°C)
Temperature (°C)
(1) IRS Method (Mounting Solder: Lead)
Soldering
220 to
245
180 to
200
250 max.
230
Upper surface of case (peak):
255˚C max.
Soldering
180
150
Preheating
Relay
terminal
section
Preheating
150
120 max.
30 max.
Time (s)
Note: The temperature profile indicates the
Time (s)
temperature of the relay terminal
section.
• The thickness of cream solder to be applied should be within a range between 150 and 200 μm on OMRON’s recommended PCB pattern.
• In order to perform correct soldering, it is recommended that the correct soldering conditions be maintained as shown below on the left side.
90 to 120
Correct Soldering
20 to 30
Incorrect Soldering
Relay
PCB
Insufficient
amount of
solder
Terminal
Solder
Land
Excessive
amount of
solder
Visually check that the Relay is properly soldered.
Precautions
■ Correct Use
Handling
Do not unpack the relay until mounting it.
Environmental Conditions During Operation,
Storage, and Transportation
Soldering
It is best to keep the relay in its packaging in a controlled environment until it is ready for mounting.
Solder: JIS Z3282, H63A or equivalent
Soldering time: Approx. 5 s max. (approx. 2 s for the first time and
approx. 3 s for the second time if the DWS method is used)
If the Relay is stored for a long time in an adverse environment with
high temperature, high humidity, organic gases, or sulfide gases, sulfide or oxide films will form on the contact surfaces. These films may
result in unstable contact, contact problems, or functional problems.
Therefore, operate, store, or transport the product under specified
environmental conditions.
Be sure to make a molten solder level adjustment so that the solder
will not overflow on the PCB.
Latching Relay Mounting
Soldering temperature: Approx. 250°C (260°C if the DWS method is
used)
Claw Securing Force During Automatic
Mounting
During automatic insertion of Relays, make sure to set the securing
force of each claw to the following so that the Relays characteristics
will be maintained.
Make sure that the vibration or shock that is generated from other
devices, such as relays in operation, on the same panel and imposed
on the Latching Relay does not exceed the rated value, otherwise the
Latching Relay that has been set may be reset or vice versa. The
Latching Relay is reset before shipping. If excessive vibration or
shock is imposed, however, the Latching Relay may be set accidentally. Be sure to apply a reset signal before use.
Maximum Allowable Voltage
The maximum allowable voltage of the coil can be obtained from the
coil temperature increase and the heat-resisting temperature of coil
insulating sheath material. (Exceeding the heat-resisting temperature may result in burning or short-circuiting.) The maximum allowable voltage also involves important restrictions which include the
following:
Direction A: 1.96 N
Direction B: 4.90 N
Direction C: 1.96 N
74
Low Signal Relay
G6K
• Must not cause thermal changes in or deterioration of the insulating
material.
• Must not cause damage to other control devices.
• Must not cause any harmful effect on people.
• Must not cause fire.
Therefore, be sure to use the maximum allowable voltage as specified in the catalog.
As a rule, the rated voltage must be applied to the coil. A voltage
exceeding the rated value, however, can be applied to the coil provided that the voltage is less than or equal to the maximum allowable
voltage. It must be noted that continuous voltage application to the
coil will cause a coil temperature increase which may affect characteristics such as electrical life and coil insulation.
Coating
The Relay mounting on the PCB may be coated or washed but do not
apply silicone coating or detergent containing silicone, otherwise the
silicone coating or detergent may remain on the surface of the Relay.
PCB Mounting
If two or more Relays are closely mounted with the long sides of the
Relays facing each other and soldering is performed with infrared
radiation, the solder may not be properly exposed to the infrared
rays. Be sure to keep the proper distance between adjacent Relays
as shown below to insure formation of good solder joints.
G6K-2G
2 mm min.
G6K-2F
2.7 mm min.
Two or more Relays may be mounted as closely as desired with the
short sides of the Relays facing each other.
Low Signal Relay
G6K
75
MEMO
76
Low Signal Relay
G6K
Omron Electronic Components, LLC
Terms and Conditions of Sales
I. GENERAL
1. Definitions: The words used herein are defined as follows.
(a) Terms:
These terms and conditions
(b) Seller:
Omron Electronic Components LLC and its subsidiaries
(c) Buyer:
The buyer of Products, including any end user in section III through VI
(d) Products: Products and/or services of Seller
(e) Including: Including without limitation
2. Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments,
invoices, purchase orders and other documents, whether electronic or in writing, relating
to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's
purchase order or other documents which are inconsistent with, or in addition to, these
Terms.
3. Distributor: Any distributor shall inform its customer of the contents after and including
section III of these Terms.
II. SALES
1. Prices; Payment: All prices stated are current, subject to change without notice by Seller.
Buyer agrees to pay the price in effect at the time the purchase order is accepted by
Seller. Payments for Products received are due net 30 days unless otherwise stated in
the invoice. Buyer shall have no right to set off any amounts against the amount owing in
respect of this invoice.
2. Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent to
Buyer after deducting transportation charges, taxes and duties, and will be allowed only
if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past
due amounts owing to Seller.
3. Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximum
legal rate, whichever is less, on any balance not paid within the stated terms.
4. Orders: Seller will accept no order less than 200 U.S. dollars net billing.
5. Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyer
shall make remittance to Seller at the then current exchange rate most favorable to
Seller; provided that if remittance is not made when due, Buyer will convert the amount
to U.S. dollars at the then current exchange rate most favorable to Seller available
during the period between the due date and the date remittance is actually made.
6. Governmental Approvals: Buyer shall be responsible for all costs involved in obtaining
any government approvals regarding the importation or sale of the Products.
7. Taxes: All taxes, duties and other governmental charges (other than general real
property and income taxes), including any interest or penalties thereon, imposed directly
or indirectly on Seller or required to be collected directly or indirectly by Seller for the
manufacture, production, sale, delivery, importation, consumption or use of the Products
sold hereunder (including customs duties and sales, excise, use, turnover and license
taxes) shall be charged to and remitted by Buyer to Seller.
8. Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller,
Seller reserves the right to stop shipments or require satisfactory security or payment in
advance. If Buyer fails to make payment or otherwise comply with these Terms or any
related agreement, Seller may (without liability and in addition to other remedies) cancel
any unshipped portion of Products sold hereunder and stop any Products in transit until
Buyer pays all amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid
accounts.
9. Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyer
indemnifies Seller fully against all costs or expenses arising in connection therewith.
10. Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting from
causes beyond its control, including earthquakes, fires, floods, strikes or other labor
disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots,
delay in or lack of transportation or the requirements of any government authority.
11. Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller:
(a) All sales and shipments of Products shall be FOB shipping point (unless otherwise
stated in writing by Seller), at which point title to and all risk of loss of the Products
shall pass from Seller to Buyer, provided that Seller shall retain a security interest in
the Products until the full purchase price is paid by Buyer;
(b) Delivery and shipping dates are estimates only; and
(c) Seller will package Products as it deems proper for protection against normal
handling and extra charges apply to special conditions.
12. Claims: Any claim by Buyer against Seller for shortage or damage to the Products
occurring before delivery to the carrier or any claim related to pricing or other charges
must be presented in detail in writing to Seller within 30 days of receipt of shipment.
III. PRECAUTIONS
1. Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY
OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE
APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING
APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE
BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONIC
COMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E)
SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT.
Buyer acknowledges that it alone has determined that the Products will meet their
requirements of the intended use in all cases. Buyer must know and observe all
prohibitions of use applicable to the Product/s.
2. Use with Attention: The followings are some examples of applications for which
particular attention must be given. This is not intended to be an exhaustive list of all
possible use of any Product, nor to imply that any use listed may be suitable for any
Product:
(a) Outdoor use, use involving potential chemical contamination or electrical
interference.
(b) Use in consumer Products or any use in significant quantities.
(c) Energy control systems, combustion systems, railroad systems, aviation systems,
medical equipment, amusement machines, vehicles, safety equipment, and
installations subject to separate industry or government regulations.
(d) Systems, machines, and equipment that could present a risk to life or property.
3. Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE
PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE
WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
4. Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZED
VEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY
SELLER.
5. Programmable Products: Seller shall not be responsible for the Buyer's programming of
a programmable Product.
IV. WARRANTY AND LIMITATION
1. Warranty: Seller's exclusive warranty is that the Products will be free from defects in
materials and workmanship for a period of twelve months from the date of sale by Seller
(or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY
OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES,
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OF THE PRODUCTS.
2. Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the form
originally shipped with Buyer responsible for labor charges for removal or replacement
thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an
amount equal to the purchase price of the Product; provided that there shall be no
liability for Seller or its affiliates unless Seller's analysis confirms that the Products were
correctly handled, stored, installed and maintained and not subject to contamination,
abuse, misuse or inappropriate modification. Return of any Products by Buyer must be
approved in writing by Seller before shipment.
3. Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED
WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL
LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF
THE PRODUCT ON WHICH LIABILITY IS ASSERTED.
4. Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and its
employees from and against all liabilities, losses, claims, costs and expenses (including
attorney's fees and expenses) related to any claim, investigation, litigation or proceeding
(whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or
omissions under these Terms or in any way with respect to the Products.
V. INFORMATION; ETC.
1. Intellectual Property: The intellectual property embodied in the Products is the exclusive
property of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way
without the written permission of Seller. Buyer (at its own expense) shall indemnify and
hold harmless Seller and defend or settle any action brought against Seller to the extent
that it is based on a claim that any Product made to Buyer specifications infringed
intellectual property rights of another party.
2. Property; Confidentiality: Notwithstanding any charges to Buyer for engineering or
tooling, all engineering and tooling shall remain the exclusive property of Seller. All
information and materials supplied by Seller to Buyer relating to the Products are
confidential and proprietary, and Buyer shall limit distribution thereof to its trusted
employees and strictly prevent disclosure to any third party.
3. Performance Data: Performance data is provided as a guide in determining suitability
and does not constitute a warranty. It may represent the result of Seller's test conditions,
and the users must correlate it to actual application requirements.
4. Change In Specifications: Product specifications and descriptions may be changed at
any time based on improvements or other reasons. It is Seller’s practice to change part
numbers when published ratings or features are changed, or when significant
engineering changes are made. However, some specifications of the Product may be
changed without any notice.
5. Errors And Omissions: The information on Seller’s website or in other documentation
has been carefully checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
6. Export Controls: Buyer shall comply with all applicable laws, regulations and licenses
regarding (a) export of the Products or information provided by Seller; (b) sale of
Products to forbidden or other proscribed persons or organizations; (c) disclosure to noncitizens of regulated technology or information.
VI. MISCELLANEOUS
1. Waiver: No failure or delay by Seller in exercising any right and no course of dealing
between Buyer and Seller shall operate as a waiver of rights by Seller.
2. Assignment: Buyer may not assign its rights hereunder without Seller's written consent.
3. Law: These Terms are governed by Illinois law (without regard to conflict of laws).
Federal and state courts in Cook County, Illinois have exclusive jurisdiction for any
dispute hereunder.
4. Amendment: These Terms constitute the entire agreement between Buyer and Seller
relating to the Products, and no provision may be changed or waived unless in writing
signed by the parties.
5. Severability: If any provision hereof is rendered ineffective or invalid, such provision shall
not invalidate any other provision.
Low Signal Relay
G6K
Certain Precautions on Specifications and Use
1. Suitability for Use. Seller shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in
Buyer's application or use of the Product. At Buyer's request, Seller will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use.
Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer's application, product or system. Buyer
shall take application responsibility in all cases but the following is a nonexhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to separate industry or government
regulations.
(iii) Use in consumer products or any use in significant quantities.
(iv) Systems, machines and equipment that could present a risk to life or
property. Please know and observe all prohibitions of use applicable to this
product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Seller shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
3. Performance Data. Performance data given in this publication is provided as
a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must
correlate it to actual application requirements. Actual performance is subject to
Seller's Warranty and Limitations of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Seller representative at any time to
confirm actual specifications of purchased Product.
5. Errors and Omissions. The information in this publication has been carefully
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors, or omissions.
6. RoHS Compliance. Where indicated, our products currently comply, to the
best of our knowledge as of the date of this publication, with the requirements
of the European Union's Directive on the Restriction of certain Hazardous
Substances ("RoHS"), although the requirements of RoHS do not take effect
until July 2006. These requirements may be subject to change. Please consult
our website for current information.
Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website
at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
OMRON ON-LINE
OMRON ELECTRONIC
COMPONENTS LLC
55 E. Commerce Drive, Suite B
Schaumburg, IL 60173
Global - http://www.omron.com
USA - http://www.components.omron.com
847-882-2288
Cat. No. X301-E-1
Low Signal Relay
06/09
G6K
Specifications subject to change without notice
Printed in USA