MURF1605CT THRU MURF1660CT SUPER FAST RECOVERY SILICON RECTIFIER Reverse Voltage - 50 to 600 Volts Forward Current - 16.0 Ampere FEATURES ITO-220AB The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 ● Super fast switching for high efficiency ● Low reverse leakage ● High forward surge current capability ● High temperature soldering guaranteed: 250 C/10 seconds,0.25 ”(6.35mm) from case ● ● Case: JEDEC ITO-220AB molded plastic body ● Terminals: Plated leads, solderable per MIL-STD-750, Method 2026 ● High temperature soldering guaranteed: .059(1.5) .043(1.1) .030(0.76) .020(0.51) .112(2.84) .088(2.24) 250 C/10 seconds, 0.25" (6.35mm) from case Polarity: As marked Mounting Position: Any Mounting Torque: 10 in-lbs maximum Weight: 0.08 ounce, 2.24 grams o .189(4.8) .173(4.4) .118(3.0) .106(2.7) .610(15.5) .571(14.5) .157(4.0) .142(3.6) MECHANICAL DATA ● ● ● ● .138(3.5) .122(3.1) .118(3.0) .102(2.6) .406(10.3) .386(9.8) .071(1.8) .055(1.4) .571(14.5) .531(13.5) .114(2.9) .098(2.5) .030(0.76) .020(0.51) Dim ensions in inches and (m illim eters) PIN 1 - + PIN 3 - PIN 2 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. Characteristic Symbol Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage MURF MURF MURF MURF 1605CT 1610CT 1615CT 1620CT MURF 1630CT MURF MURF 1640CT 1660CT Unit VRRM VRWM VR 50 100 150 200 300 400 600 V VR(RMS) 35 70 105 140 210 280 420 V Average Rectified Output Current @TC = 105°C IO 16 A Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave superimposed on rated load (JEDEC Method) IFSM 125 A Forward Voltage VFM @IF = 8.0A Peak Reverse Current @TA = 25°C At Rated DC Blocking Voltage @TA = 125°C 0.95 1.3 1.7 10 500 IRM V µA Reverse Recovery Time (Note 1) trr 35 50 nS Typical Junction Capacitance (Note 2) Cj 80 60 pF Operating and Storage Temperature Range Tj, TSTG -65 to +150 °C www.kersemi.com MURF1605CT THRU MURF1660CT RATINGS AND CHARACTERISTIC CURVES IF, INSTANTANEOUS FORWARD CURRENT (A) I(AV), AVERAGE FORWARD CURRENT (A) 20 16 12 8 4 0 0 50 100 100 1605 - 1620 1660 1.0 Pulse width = 300µs 2% duty cycle 0.1 0 150 TC, CASE TEMPERATURE (°C) Fig. 1 Forward Current Derating Curve 150 75 1.8 100 10 Tj = 25°C f = 1.0MHz 100 MURF1605CTMURF1620CT MURF1640CTMURF1660CT 10 1 1.2 400 8.3 ms single half-sine-wave JEDEC method 0 0.6 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 2 Typical Forward Characteristics Cj, CAPACITANCE (pF) IFSM, PEAK FORWARD SURGE CURRENT (A) 225 1630 - 1640 10 0.1 1.0 10 VR, REVERSE VOLTAGE (V) Fig. 4 Typical Junction Capacitance NUMBER OF CYCLES AT 60Hz Fig. 3 Maximum Non-Repetitive Surge Current trr 50Ω NI (Non-inductive) (-) 10Ω NI Device Under Test (+) +0.5A (-) Pulse Generator (Note 2) 50V DC Approx 1.0Ω NI Oscilloscope (Note 1) 0A -0.25A (+) Notes: 1. Rise Time = 7.0ns max. Input Impedance = 1.0MΩ, 22pF. 2. Rise Time = 10ns max. Input Impedance = 50Ω. -1.0A Set time base for 5/10ns/cm Fig. 5 Reverse Recovery Time Characteristic and Test Circuit 100