Dual Laser Driver with APC Amp Features General Description • Read + 3Write Channel laser driver with oscillator and fast I/V amplifier plus a separate ROM laser driver with oscillator • 200V/µs I/V amplifier • 100X gain, 100mA low noise read channel • 200X gain, 200mA write channel plus two 100X gain, 100mA write channels • 500MHz, 100mAP-P Oscillator • Write Rise/Fall times = 0.8ns • Single +5V supply The EL6280C is a combination read + 3 write level laser driver and IV amplifier, with an extra read + oscillator ROM channel for use in duallaser ‘Combo’ drivers. A separate (amplitude and frequency) oscillator modulates the selected output for laser noise reduction during read or write. All these functions are provided in a 24 lead QSOP package. Applications Combo CD-RW + DVD-ROM CD-RW to 16X CD-R to 32X Writable Optical Disk Drives The 100mAP-P (max) oscillator is switched on and off by the OSCEN line. The CD line allows the oscillator to operate at different amplitudes and frequencies for each laser. The entire chip is powered down when ENABLE is low. The user can define the gain of the I/V amplifier. With a slew rate of 200V/µs, the I/V amplifier can normally settle to 1% within 30ns. 2 VREF VDD 23 3 IINR VDD 22 4 IIN2 IOUT1 21 5 RF1 GND 20 6 IIN3 GND 19 7 IIN4 RAMP1 18 8 RF2 RAMP2 17 9 WEN2 ENABLE 16 10 CD IIN2 1 19 VCC RF1 2 18 IOUT1 IIN3 3 17 GND IIN4 4 16 GND RF2 5 15 RAMP1 WEN2 6 14 RAMP2 CD 7 13 ENABLE OSCEN 15 11 WEN3 IOUT2 14 12 WEN4 VDD 13 20 VCC PDIN 24 Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation. © 2001 Elantec Semiconductor, Inc. October 25, 2001 1 VOUT OSCEN 12 MDP0046 21 PDIN LPP-24 IOUT2 11 MDP0040 22 VOUT Outline # QSOP-24 VCC 10 Package 0°C to +70°C 23 VREF Temp. Range WEN4 9 Part No. EL6280CU 24 IINR Connection Diagram Ordering Information EL6280CL The CD pin when high selects the CD (write) laser. Positive current supplied to the IIN lines, through a user selected resistor, allow the full scale range of each amplifier to be matched to the full scale range of the users control DACs. When the write laser is selected, and the WEN pins are switched low, the respective current is summed to the output with 1ns rise and fall times. Write channel 2 has 200mA output capability with an 200X gain amplifier. WEN3 8 • • • • EL6280C - Product Brief EL6280C - Product Brief EL6280C - Product Brief EL6280C - Product Brief Dual Laser Driver with APC Amp General Disclaimer Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the circuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement. October 25, 2001 WARNING - Life Support Policy Elantec, Inc. products are not authorized for and should not be used within Life Support Systems without the specific written consent of Elantec, Inc. Life Support systems are equipment intended to support or sustain life and whose failure to perform when properly used in accordance with instructions provided can be reasonably expected to result in significant personal injury or death. Users contemplating application of Elantec, Inc. Products in Life Support Systems are requested to contact Elantec, Inc. factory headquarters to establish suitable terms & conditions for these applications. Elantec, Inc.’s warranty is limited to replacement of defective components and does not cover injury to persons or property or other consequential damages. Elantec Semiconductor, Inc. 675 Trade Zone Blvd. Milpitas, CA 95035 Telephone: (408) 945-1323 (888) ELANTEC Fax: (408) 945-9305 European Office: +44-118-977-6020 Japan Technical Center: +81-45-682-5820 2 Printed in U.S.A.