Freescale MPXHZ6400A Media resistant and high temperature accuracy intergrated silicon pressure sensor Datasheet

Freescale Semiconductor
Technical Data
MPXHZ6400A
Rev 0, 08/2005
Media Resistant and
High Temperature Accuracy
Integrated Silicon Pressure Sensor
for Measuring Absolute Pressure,
On-Chip Signal Conditioned,
Temperature Compensated
and Calibrated
The Freescale MPXHZ6400A series sensor integrates on-chip, bipolar op
amp circuitry and thin film resistor networks to provide a high output signal and
temperature compensation. The small form factor and high reliability of on-chip
integration make the Freescale pressure sensor a logical and economical choice
for the system designer.
The MPXHZ6400A series piezoresistive transducer is a state-of-the-art,
monolithic, signal conditioned, silicon pressure sensor. This sensor combines
advanced micromachining techniques, thin film metallization, and bipolar
semiconductor processing to provide an accurate, high level analog output signal
that is proportional to applied pressure.
Figure 1 shows a block diagram of the internal circuitry integrated on a
pressure sensor chip.
MPXHZ6400A
INTEGRATED
PRESSURE SENSOR
20 TO 400 kPA (3.0 TO 58 psi)
0.2 TO 4.8 V OUTPUT
(3.0 TO 58 psi)
SUPER SMALL OUTLINE PACKAGE
MPXHZ6400AC6T1
CASE 1317A-03
Features
•
•
•
•
•
•
Improved Accuracy at High Temperature
Available in Small and Super Small Outline Packages
1.5% Maximum Error over 0° to 85°C
Ideally suited for Microprocessor or Microcontroller-Based Systems
Temperature Compensated from –40° to +125°C
Durable Thermoplastic (PPS) Surface Mount Package
Typical Applications
•
•
ORDERING INFORMATION
Ported
Element
Options
Case
No.
MPX Series
Order No.
1
N/C
5
N/C
2
VS
6
N/C
3
GND
7
N/C
4
VOUT
8
N/C
1. Pins 1, 5, 6, 7, and 8 are internal device
connections. Do not connect to external
circuitry or ground. Pin 1 is noted by the
notch in the lead.
Industrial Controls
Engine Control/Liquified Petroleum Gas (LPG)
Device
Type
PIN NUMBERS(1)
Packing
Options
Device
Marking
Absolute, Axial 1317A MPXHZ6400AC6T1 Tape & Reel MPXHZ6400A
Port
© Freescale Semiconductor, Inc., 2005. All rights reserved.
VS
Thin Film
Temperature
Compensation
and
Gain Stage #1
Sensing
Element
GND
Gain Stage #2
and
Ground
Reference
Shift Circuitry
Vout
Pins 1, 5, 6, 7, and 8 are NO CONNECTS
for small outline package devices
Figure 1. Fully Integrated Pressure Sensor Schematic
Table 1. Maximum Ratings(1)
Rating
Symbol
Value
Unit
Maximum Pressure
PMAX
1600
kPa
Storage Temperature
TSTG
–40° to +125°
°C
Operating Temperature
TA
–40° to +125°
°C
Output Source Current @ Full Scale Output(2)
I o+
0.5
mAdc
Output Sink Current @ Minimum Pressure Offset2
Io –
–0.5
mAdc
1. Exposure beyond the specified limits may cause permanent damage or degradation to the device.
2. Maximum Output Current is controlled by effective impedance from Vout to GND or Vout to VS in the application circuit.
MPXHZ6400A
2
Sensors
Freescale Semiconductor
Table 2. Operating Characteristics (VS = 5.0 Vdc, TA = 25°C.)
Characteristic
Symbol
Min
Typ
Max
Unit
Pressure Range
POP
20
—
400
kPa
Supply Voltage(1)
VS
4.64
5.0
5.36
Vdc
Supply Current
Io
—
6.0
10
mAdc
Minimum Pressure Offset
@ VS = 5.0 Volts(2)
(0 to 85°C)
Voff
0.133
0.2
0.267
Vdc
Full Scale Output
@ VS = 5.0 Volts(3)
(0 to 85°C)
VFSO
4.733
4.8
4.866
Vdc
Full Scale Span
@ VS = 5.0 Volts(4)
(0 to 85°C)
VFSS
4.467
4.6
4.733
Vdc
Accuracy(5)
(0 to 85°C)
—
—
—
±1.5
%VFSS
V/P
—
12.1
—
mV/kPa
Response Time(6)
tR
—
1.0
—
ms
Warm-Up Time(7)
—
—
20
—
ms
Offset Stability(8)
—
—
±0.25
—
%VFSS
Sensitivity
1. Device is ratiometric within this specified excitation range.
2. Offset (Voff) is defined as the output voltage at the minimum rated pressure.
3. Full Scale Output (VFSO) is defined as the output voltage at the maximum or full rated pressure.
4. Full Scale Span (VFSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the
minimum rated pressure.
5. Accuracy is the deviation in actual output from nominal output over the entire pressure range and temperature range as a percent of span
at 25°C due to all sources of error including the following:
Linearity:Output deviation from a straight line relationship with pressure over the specified pressure range.
Temperature Hysteresis:Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and
from the minimum or maximum operating temperature points, with zero differential pressure applied.
Pressure Hysteresis:Output deviation at any pressure within the specified range, when this pressure is cycled to and from the minimum or
maximum rated pressure, at 25°C.
TcSpan:Output deviation over the temperature range of 0 to 85°C, relative to 25°C.
TcOffset:Output deviation with minimum rated pressure applied, over the temperature range of 0 to 85°C, relative to 25°C.
Variation from Nominal:The variation from nominal values, for Offset or Full Scale Span, as a percent of VFSS, at 25°C.
6. Response Time is defined as the time for the incremental change in the output to go from 10% to 90% of its final value when subjected to a
specified step change in pressure.
7. Warm-up Time is defined as the time required for the product to meet the specified output voltage after the Pressure has been stabilized.
8. Offset Stability is the product's output deviation when subjected to 1000 hours of Pulsed Pressure, Temperature Cycling with Bias Test.
MPXHZ6400A
Sensors
Freescale Semiconductor
3
Figure 2 illustrates a typical application circuit (output
source current operation).
Figure 3 shows the sensor output signal relative to
pressure input. Typical minimum and maximum output
curves are shown for operation over 0 to 85°C temperature
range. The output will saturate outside of the rated pressure
range.
A gel die coat isolates the die surface and wire bonds from
the environment, while allowing the pressure signal to be
transmitted to the silicon diaphragm. The MPXHZ6400A
series pressure sensor operating characteristics, internal
reliability and qualification tests are based on use of dry air as
the pressure media. Media other than dry air may have
adverse effects on sensor performance and long-term
reliability. Contact the factory for information regarding media
compatibility in your application.
+5.0 V
VS Pin 2
MPXHZ6400A
VOUT Pin 4
100 nF
To ADC
47 pF
GND Pin 3
51 K
Figure 2. Typical Application Circuit
(Output Source Current Operation)
5.0
4.5
4.0
Output (Volts)
3.5
Transfer Function:
VOUT = VS x (0.002421xP–0.00842 ± Error
VS = 5.0 VDC
Temperature = 0 to 85°C
3.0
2.5
MAX
2.0
TYP
1.5
1.0
0
MIN
20
40
60
80
100
120
140
160
180
200
220
240
260
280
300
320
340
360
380
400
0.5
Pressure (Reference to Sealed Vacuum) in kPa
Figure 3. Output versus Absolute Pressure
MPXHZ6400A
4
Sensors
Freescale Semiconductor
Transfer Function (MPXHZ6400A)
Normal Transfer Value: VOUT = VS x (0.002421 x P – 0.0.00842)
± Pressure Error x Temp. Factor x 0.002421 x VS
VS = 5.0 ± 0.36 VDC
Temperature Error Band
MPXHZ6400A
4.0
3.0
Temperature
Error
Factor
Break Points
2.0
1.0
Temp
0.0
-40
-20
0
20
80
40
60
Temperature in C°
100
120
140
NOTE: The Temperature Multiplier is a linear response from 0°C to -40°C and from 85°C to 125°C
Multiplier
- 40
0 to 85
125
3
1
1.75
Pressure Error Band
Error Limits for Pressure
±5.5 (kPa)
6.0
5.0
4.0
Pressure Error (kPa)
3.0
2.0
1.0
0.0
-1.0
20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 400
-2.0
-3.0
-4.0
- 5.0
Pressure (in kPa)
Pressure
Error (Max)
- 6.0
20 to 400 (kPa)
±5.5 (kPa)
SURFACE MOUNTING INFORMATION
Minimum Recommended Footprint for Super Small Outline Packages
Surface mount board layout is a critical portion of the total
0.050
0.387
design. The footprint for the semiconductor package must be
1.27
9.83
TYP
the correct size to ensure proper solder connection interface
between the board and the package. With the correct pad
geometry, the packages will self-align when subjected to a
0.150
solder reflow process. It is always recommended to fabricate
3.81
boards with a solder mask layer to avoid bridging and/or
shorting between solder pads, especially on tight tolerances
and/or tight layouts.
0.027 TYP 8X
0.69
0.053 TYP 8X
1.35
inch
mm
Figure 4. SSOP Footprint (Case 1317A)
MPXHZ6400A
Sensors
Freescale Semiconductor
5
PACKAGE DIMENSIONS
PAGE 1 OF 2
CASE 1317A-03
ISSUE C
SUPER SMALL OUTLINE PACKAGE
MPXHZ6400A
6
Sensors
Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 2 OF 2
CASE 1317A-03
ISSUE C
SUPER SMALL OUTLINE PACKAGE
MPXHZ6400A
Sensors
Freescale Semiconductor
7
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
MPXHZ6400A
Rev. 0
08/2005
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2005. All rights reserved.
Similar pages