Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type) Data Sheet Chip Inductor (Chip Coil) 1 Power Inductor (Wire Wound Type) LQH6PP Series (2424 Size) ■ Dimensions ■ Packaging Code Packaging Minimum Quantity L 180mm Embossed Tape 250 K 330mm Embossed Tape 1500 (0.2) 4.3±0.2 6.0±0.2 6.0±0.2 6.0±0.2 1.65±0.2 (in mm) 1.65±0.2 ■ Rated Value (p: packaging code) Part Number Inductance Inductance Allowable DC Current Test Frequency (Based on Temperature Rise) Allowable DC Current (Based on Inductance Change) DC Resistance Self Resonance Frequency (min.) Class of Magnetic Shield LQH6PPN1R0N43p 1.0µH±30% 100kHz 4.30A 7.50A 0.009ohm±30% 110MHz Magnetic shield of magnetic powder in resin LQH6PPN1R5N43p 1.5µH±30% 100kHz 4.15A 6.50A 0.010ohm±30% 60MHz Magnetic shield of magnetic powder in resin LQH6PPN2R2N43p 2.2µH±30% 100kHz 4.10A 5.60A 0.014ohm±30% 30MHz Magnetic shield of magnetic powder in resin LQH6PPN3R3N43p 3.3µH±30% 100kHz 3.80A 4.50A 0.016ohm±30% 30MHz Magnetic shield of magnetic powder in resin LQH6PPN4R7M43p 4.7µH±20% 100kHz 3.20A 4.00A 0.020ohm±30% 25MHz Magnetic shield of magnetic powder in resin LQH6PPN6R8M43p 6.8µH±20% 100kHz 2.85A 3.20A 0.028ohm±30% 20MHz Magnetic shield of magnetic powder in resin LQH6PPN100M43p 10µH±20% 100kHz 2.60A 2.60A 0.044ohm±30% 15MHz Magnetic shield of magnetic powder in resin LQH6PPN150M43p 15µH±20% 100kHz 2.20A 2.20A 0.065ohm±30% 10MHz Magnetic shield of magnetic powder in resin LQH6PPN220M43p 22µH±20% 100kHz 1.55A 1.70A 0.108ohm±30% 10MHz Magnetic shield of magnetic powder in resin LQH6PPN330M43p 33µH±20% 100kHz 1.29A 1.60A 0.137ohm±30% 6MHz Magnetic shield of magnetic powder in resin LQH6PPN470M43p 47µH±20% 100kHz 1.10A 1.25A 0.230ohm±30% 6MHz Magnetic shield of magnetic powder in resin LQH6PPN680M43p 68µH±20% 100kHz 1.00A 1.10A 0.289ohm±30% 5MHz Magnetic shield of magnetic powder in resin LQH6PPN101M43p 100µH±20% 100kHz 0.80A 0.92A 0.436ohm±30% 3MHz Magnetic shield of magnetic powder in resin Operating Temperature Range: -40 to +85°C Only for reflow soldering. ■ Notice (Allowable DC Current) <Allowable DC Current> When Allowable DC Current is applied to the Products, self-generation of heat will rise to 40°C or less. When Allowable DC Current is applied to the Products, Inductance will be within +-30% of nominal Inductance value. Continued on the following page. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.4.30 http://www.murata.com/ Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type) Data Sheet 2 Continued from the preceding page. ■ Inductance-Frequency Characteristics (Typ.) 100µH Inductance (µH) 100 10 68µH 47µH 33µH 22µH 15µH 10µH 6.8µH 4.7µH 3.3µH 2.2µH 100µH 68µH 47µH 33µH 22µH 15µH 10µH 6.8µH 4.7µH 3.3µH 2.2µH 1.5µH 1.0µH 100 Inductance (µH) 1000 ■ Inductance-Current Characteristics (Typ.) 1.5µH 10 1 1.0µH 1 0.1 0.1 1 10 Frequency (MHz) 100 0.1 10 1000 100 1000 10000 DC Current (mA) ■ Temperature Rise Characteristics (Typ.) 40 100µH 15µH 68µH 6.8µH 22µH 47µH 4.7µH 10µH Temperature Rise (°C) 30 33µH 20 3.3µH 2.2µH 1.5µH 1.0µH 10 0 0 1000 2000 3000 4000 5000 DC Current (mA) ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.4.30 http://www.murata.com/