Wide Gap Slotted Optical Switch OPB800 (L and W Series) W Package Features: 0.375” (9.525 mm) wide gap Choice of aperture size Choice of minimum photocurrent Choice of opaque or IR transmissive shells Available for PCBoard mounting or with 24” 26 AWG wires L Package Description: The OPB800L series, PCBoard mounting, of wide gap switch provides the flexibility of a custom device from a standard product line, while the OPB800W series, remote mounted, switch offers 24” (610 mm) 26 AWG wire interconnect. Building from a standard housing that utilizes a 0.375” (9.5 mm) wide slot, a user can specify the electrical output parameters, discrete shell material and the aperture width. Housings are made from an opaque grade of injection-molded plastic that minimizes the assembly’s sensitivity to visible and near-infrared ambient radiation. Discrete shells, which are exposed on parallel faces inside the device throat, are made of IR transmissive plastic (for applications where aperture contamination may occur) or of opaque plastic with aperture openings (for maximum protection against ambient light). Applications: Non-contact interruptive object sensing Assembly line automation Machine automation Equipment security Machine safety Part Number Guide OPB 8 X X X X X Z For “W” series only Sensor Aperture: 1 — 0.010” (.254 mm) 5 — 0.050” (1.270 mm) Optek Assembly Phototransistor Output Family Emitter Aperture: 5 — 0.050” (1.270 mm) Discrete Shell Material: 0 — Transmissive plastic Discrete shell 1 — Opaque plastic Discrete shell Mounting configurations: L — Solder lead termination W — Wire termination Electrical Specification Variations: 0 = Electrical Parameter A 1 = Electrical Parameter B 2 = Electrical Parameter C Note: Assemblies with 0.010” apertures are currently available with electrical parameter “A” only. Wires = 26AWG—24” Long General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | Optek Technology, Inc. 1645 Wallace Drive, Ste. 130, Carrollton, TX USA 75006 |Ph: +1 972 323 2200 www.ttelectronics.com | [email protected] Issue B 11/2016 Page 1 Wide Gap Slotted Optical Switch Electrical Specifications Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage and Operating Temperature L Series W Series -40° C to +85° C -40° C to +80° C Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron](2) 260° C Input Diode Forward DC Current 50 mA Peak Forward Current (1 µs pulse width, 300 pps) 3A Reverse DC Voltage 2V (1) 100 mW Power Dissipation Output Phototransistor Collector-Emitter Voltage 30 V Emitter-Collector Voltage 5V Collector DC Current Power Dissipation 30 mA (1) 100 mW 1 2 General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc 3 Color/Pin # Description Red-1 Anode Black-2 Cathode White-3 Collector Green-4 Emitter 4 TT Electronics | Optek Technology, Inc. 1645 Wallace Drive, Ste. 130, Carrollton, TX USA 75006 |Ph: +1 972 323 2200 www.ttelectronics.com | [email protected] Issue B 11/2016 Page 2 Wide Gap Slotted Optical Switch Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode VF Forward Voltage - - 1.7 V IF = 20 mA IR Reverse Current - - 100 µA VR = 2 V Output Phototransistor V(BR)CEO Collector-Emitter Breakdown Voltage 30 - - V IC = 1 mA V(BR)ECO Emitter-Collector Breakdown Voltage 5 - - V IE = 100 µA Collector-Emitter Dark Current - - 100 nA VCE = 10 V VCE(SAT) Collector-Emitter Saturation Voltage Parameter A (OPB800,OPB810) Parameter B (OPB801,OPB811) Parameter C (OPB802,OPB812) - - 0.4 0.4 0.6 V V V IC = 250 µA, IF = 20 mA IC = 500 µA, IF = 10 mA IC = 1800 µA, IF = 20 mA IC(ON) On-State Collector Current Parameter A (OPB800,OPB810) Parameter B (OPB801,OPB811) Parameter C (OPB802,OPB812) 0.625 1.25 2.25 - - mA ICEO Combined Notes: (1) (2) (3) (4) (5) VCE = 10 V, IF = 20 mA VCE = 5 V, IF = 10 mA VCE = 0.6 V, IF = 20 mA Derate linearly 1.67 mW/° C above 25° C. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. All parameters tested using pulse technique. Methanol or isopropanol are recommended as cleaning agents. Plastic housing is soluble in chlorinated hydrocarbons and ketones. The W Series includes wire terminations of 24” (610 mm) 7-strand, 26 AWG UL insulated wire on each terminal. Each device incorporates a wire strain relief at the housing surface. The insulation functions and colors are: anode (red), cathode (black), phototransistor collector (white) and phototransistor emitter (green). General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | Optek Technology, Inc. 1645 Wallace Drive, Ste. 130, Carrollton, TX USA 75006 |Ph: +1 972 323 2200 www.ttelectronics.com | [email protected] Issue B 11/2016 Page 3 Wide Gap Slotted Optical Switch OPB800_51 - Flag Next to Emitter OPB800_51 - Flag Next to Sensor 1.2 1.2 Top to Bottom Top to 1.0 Normalized IC(ON) Response Normalized IC(ON) Response 1.0 0.8 Left to Right Right to Left 0.6 0.4 Right to Left Left to Right Top to Bottom 0.8 Left to Right Right to Left 0.6 0.4 Right to Left Left to Right Top to Bottom 0.2 0.2 0.0 0.00 0.05 0.10 0.15 Distance (inches) 0.20 0.25 0.0 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPB800_51 - Flag in Middle of Slot 1.2 Top to 1.0 Normalized IC(ON) Response 0 Top to Bottom 0.8 Left to Right Right to Left 0.6 Emitter Left to Right 0.4 Right to Left Right to Left Left to Right Top to Bottom Sensor 0.2 0 0.0 0.00 0.05 0.10 0.15 0.20 Width 0.25 Distance (inches) General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | Optek Technology, Inc. 1645 Wallace Drive, Ste. 130, Carrollton, TX USA 75006 |Ph: +1 972 323 2200 www.ttelectronics.com | [email protected] Issue B 11/2016 Page 4 Wide Gap Slotted Optical Switch OPB800_55 - Flag Next to Emitter OPB800_55 - Flag Next to Sensor 1.2 1.2 Top to Top to 1.0 Normalized IC(ON) Response Normalized IC(ON) Response 1.0 0.8 Left to Right Right to Left 0.6 0.4 Right to Left Left to Right Top to Bottom 0.2 0.8 Left to Right Right to Left 0.6 0.4 Right to Left Left to Right Top to Bottom 0.2 0.0 0.00 0.05 0.10 0.15 0.20 Distance (inches) 0.25 0.0 0.00 0.05 0.10 0.15 0.20 0.25 Distance (inches) OPB800_55 - Flag in Middle of Slot 1.2 Top to 1.0 Typical IC(ON) Response (mA) 0 Top to Bottom 0.8 Left to Right Right to Left 0.6 Emitter Left to Right 0.4 Right to Left Right to Left Left to Right Top to Bottom Sensor 0.2 0 0.0 0.00 0.05 0.10 0.15 0.20 Width 0.25 Distance (inches) General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | Optek Technology, Inc. 1645 Wallace Drive, Ste. 130, Carrollton, TX USA 75006 |Ph: +1 972 323 2200 www.ttelectronics.com | [email protected] Issue B 11/2016 Page 5