MCH43 Ceramic capacitors Multi-layer ceramic chip capacitors MCH43 (4532 (1812) size, chip capacitor) zFeatures 1) High capacitance 2) Achieved high capacitance by thin and multi layer technology 3) Lead-free plating terminal 4) No polarity zQuick Reference The design and specifications are subject to change without prior notice. Please check the most recent technical specifications prior to placing orders or using the product. For more detail information regarding packaging style code, please check product designation. zThermal compensation Part No. Size code MCH43 4532 (1812) Temperature characteristics (ppm/°C) code AN 0±30 (CG) (C0G) Operating temp. range (°C) Rated voltage (V) Capacitance (pF) Capacitance tolerance Thickness (mm) −55 to +125 50 150,000 (E6 Series) 220,000 (E6 Series) J(±5%) 2.5 ± 0.3 3.2 ± 0.3 zHigh dielectric constant Part No. Size code code Temperature characteristics Operating temp. range (°C) ±10% (B) −25 to +85 ±15% (R) (X7R) −55 to +125 Rated voltage (V) 50 25 50 25 CN 16 MCH43 4532 (1812) ±15% (X5R) +30% , −80% (F) −55 to +85 10 −25 to +85 FN +22% , −82% (Y5V) −30 to +85 6.3 50 25 16 10 50 25 16 10 Capacitance (pF) 2,200,000 (E6 Series) 3,300,000 (E6 Series) 4,700,000 (E6 Series) 6,800,000 (E6 Series) 2,200,000 (E6 Series) 3,300,000 (E6 Series) 4,700,000 (E6 Series) 6,800,000 (E6 Series) 10,000,000 (E6 Series) 15,000,000 (E6 Series) 22,000,000 (E6 Series) 33,000,000 (E6 Series) 47,000,000 (E6 Series) 68,000,000 to 100,000,000 (E6 Series) 10,000,000 (E3 Series) 22,000,000 (E3 Series) 47,000,000 (E3 Series) 100,000,000 (E3 Series) 10,000,000 (E3 Series) 22,000,000 (E3 Series) 47,000,000 (E3 Series) 100,000,000 (E3 Series) Capacitance tolerance Thickness (mm) K(±10%) 1.6 ± 0.2 2.0 ± 0.2 1.6 ± 0.2 2.0 ± 0.2 1.6 ± 0.2 2.0 ± 0.2 1.6 ± 0.2 2.0 ± 0.2 2.5 ± 0.3 2.3 ± 0.2 2.5 ± 0.3 2.3 ± 0.2 M(±20%) 2.8 ± 0.3 2.0± 0.2 2.5± 0.3 Z(+80% , −20%) 2.0± 0.2 2.5± 0.3 1/10 MCH43 Ceramic capacitors zExternal dimensions (Unit : mm) Product thickness(mm) 1.6±0.2 2.0±0.2 2.3±0.2 2.5±0.3 2.8±0.3 3.2±0.3 T 0.2Min. T 4.5±0.4 3.2±0.4 zProduct designation Code Product thickness Packing specification Reel Basic ordering unit (pcs.) P 1.6mm Plustic tape (width 12mm, pitch 8mm) φ180mm (7in.) 1,000 P 2.0mm Plustic tape (width 12mm, pitch 8mm) φ180mm (7in.) 1,000 P 2.3mm Plustic tape (width 12mm, pitch 8mm) φ180mm (7in.) 500 P 2.5mm Plustic tape (width 12mm, pitch 8mm) φ180mm (7in.) 500 P 2.8mm Plustic tape (width 12mm, pitch 8mm) φ180mm (7in.) 500 P 3.2mm Plustic tape (width 12mm, pitch 8mm) φ180mm (7in.) 500 Reel (φ180mm) : compatible with EIAJ ET-7200A Packing Style Part No. M C H Rated voltage Code Voltage 8 6.3V 4 10V 3 16V 2 25V 5 50V 4 3 3 F N 4 7 6 Temperature characteristic code : Refer to quick reference table. Z P Nominal capacitance 3-digit designation according to IEC Capacitance tolerance Tolerance Code M ±5% (11pF or more) ±10% ±20% Z +80%, −20% J K 2/10 MCH43 Ceramic capacitors •Performance and test method No. Items Performance Test Method (As per JIS C 5101-1, JIS C 5101-10) 1 Appearance and dimensions No marked defects shall be allowed As per 4.4 of JIS C 5101-1. As per 4.5 of JIS C 5101-10 for appearance. Dimensions shall be as specified the Using a Magnifier. clause 4. 2 Withstanding voltage No dielectrical breakdown or other damage shall be allowed. As per 4.6 of JIS C 5101-1. As per 4.6.4 of JIS C 5101-10 Voltage shall be applied as per Table1. Table 1 CharacVoltage teristic 300% Rated voltage AN CN 250% Rated voltage FN Voltage shall be applied for 1 to 5s with 50mA charging and discharging current. 3 Insulation resistance Not less than 10000MΩ or 500MΩ µF, whichever is less. (For products with rated voltage less than 16V, it is not less than 10000MΩ or 100MΩ µF, whichever is less.) As per 4.5 of JIS C 5101-1. As per 4.6.3 of JIS C 5101-10 Measurements shall be made after 60+/−5s period of the rated voltage applied. 4 Capacitance Capacitance shall be within specified tolerance range. As per 4.7 of JIS C 5101-1. As per 4.6.1 of JIS C 5101-10 Measurements shall be made under the conditions specified in Table 2. Characteristic AN 5 Dielectric loss tangent AN tan δ < − 0.1% CN Rated voltage=16, 10V tan δ < − 7.5% Table 2 Frequency Voltage CN 1+/−0.1kHz 0.5 to 5Vrms. < > 10µF − 10µF FN 1+/−0.1KHz 120+/−24Hz 1+/−0.2Vrms. 0.5+/−0.2Vrms. As per 4.8 of JIS C 5101-1. As per 4.6.2 of JIS C 5101-10 Measurements shall be made under the conditions specified in Table 2. Rated voltage=6.3V tan δ < − 10.0% FN Rated voltage=16V tan δ < − 10.0% Rated voltage=10V tan δ < − 12.5% 3/10 MCH43 Ceramic capacitors No. Items 6 Temperature characteristic Performance AN 0+/−30ppm / °C (−55°C to +125°C) CN FN 7 Solderability 8 Resistance to solderin heat B +/−10% (−25°C to +85°C) X5R +/−15% (−55°C to +85°C) Appearance Without mechanical damage. AN Within +/−2.5% CN Within +/−7.5% FN Within +/−20% Dielectric loss tangent Within specified initial value. Insulation resistance Within specified initial value. Withstanding No defects shall be allowed. voltage 9 End termination adherence As per 4.24 of JIS C 5101-1. As per 4.7 of JIS C 5101-10 Temperature coefficient shall be calculated at 20°C and 85°C. As per 4.24 of JIS C 5101-1. As per 4.7 of JIS C 5101-10 If required, measurements shall be made at a given temperature. +30%, −80% (−25°C to +85°C) +22%, −82% (−30°C to +85°C) More than 3/4 of each end termination shall be covered with new solder. Change rate from initial value Test Method (As per JIS C 5101-1, JIS C 5101-10) Without peeling or sign of peeling shall be allowed on the end terminations. As per 4.15.2 of JIS C 5101-1. As per 4.11 of JIS C 5101-10 The solder specified in JIS Z 3282 H63A shall be used. Ans the flux containing 25% rosin and ethanol solution shall be used. The specimens shall be immersed into the solder at 235+/−5°C for 2+/−0.5s So that both end terminations are completely under solder. As per 4.14 of JIS C 5101-1. As per 4.10 of JIS C 5101-10 The solder specified in JIS Z 3282. H63A shall be used. The specimens shall be immersed into the solder at 260+/−5°C for 5+/−0.5s so that both end terminations are completely under the solder. Pre-heating at 150+/−10°C for 1 to 2min Initial measurements prior to test shall be performed after the thermal Pre-conditioning specified in Remarks (1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. Table3 Characteristic AN CN, FN Time 24+/−2 h 48+/−4 h As per 4.13 of JIS C 5101-1. As per 4.8 ofJIS C 5101-10 A 5N weight for 10+/−1s shall be applied to the soldered specimens as shown by the arrow mark in the below sketch. Applied pressure Substrate Capacitor 4/10 MCH43 Ceramic capacitors No. Items Performance Test Method (As per JIS C 5101-1, JIS C 5101-10) 10 Bending strength Appearance Without mechanical damage. As per 4.35 of JIS C 5101-1. As per 4.9 of JIS C 5101-10 Glass epoxy board with soldered specimens shall be bent till 1mm by 1.0mm/s. 11 Vibration Appearance Without mechanical damage. As per 4.17 of JIS C 5101-1. The specimens shall be soldered on the specified test jig. Initial measurements shall be made after the thermal pre-conditioning specified in Remarks(1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. [Condition] Directions : 2h each X, Y and Z directions Total : 6h Frequency range : 10 to 55 to 10Hz(1min) Applitude : 1.5mm (shall not exceed acceleration196m/s2) Change rate from initial value Dielectric loss tangent AN Capacitance shall be within specified tolerance range. CN Within +/−7.5% FN Within +/−20% Within specified initial value. Table3 Characteristic AN CN, FN 12 Temperature Appearance Without mechanical damage. cycling Change A N Within +/−2.5% rate from initial value Rated voltage C N 25V,16V,10V Within +/−7.5% Rated voltage Within +/−10% 6.3V FN Dielectric loss tangent Insulation resistance Within +/−20% Within specified initial value. Within specified initial value. Withstanding No defects shall be allowed. voltage Time 24+/−2 h 48+/−4 h As per 4.16 of JIS C 5101-1 As per 4.12 of JIS C 5101-10 The specimens shall be soldered on the test jig shown in Remarks. Temperature cycle : 100cycles Initial measurements prior to test shall be performed after the thermal per-conditioning specified in Remarks (1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. Test condition Step Temp. (°C) Time (min) 1 Min operating temp. 2 Room temp. 30+/−3 < −3 3 Max operating temp. 4 Room temp. 30+/−3 < −3 Table3 Characteristic AN CN, FN Time 24+/−2 h 48+/−4 h 5/10 MCH43 Ceramic capacitors No. 13 Humidity (Steady) Items Test Method (As per JIS C 5101-1, JIS C 5101-10) Appearance Without mechanical damage. Change rate from initial value Dielectric tangent Insulation resistance 14 Humidity life test Performance As per 4.22 of JIS C 5101-1 JIS C 5101-10 Within +/−5.0% AN Test temperature : 60+/−2°C Relative humidity : 90 to 95% Rated voltage : 500 +24/−0 h 25V,16V,10V Within +/−12.5% Test time CN Initial measurements prior to test shall Rated voltage Within +/−25.0% 6.3V be made after the voltage pre-conditioning specified in Within +/−30% FN Remarks (2). Final measurements have been left at tan δ < AN − 0.3% room temperature as per Table3. CN Less than 200% of initial spec. FN Less than 150% of initial spec. Not less than 1000MΩ or 50MΩ µF, whichever is less. (For products with rated voltage less than 16V, it is not less than 1000MΩ or 10MΩ µF, whichever is less.) Table3 Characteristic AN CN, FN Time 24+/−2 h 48+/−4 h Appearance Without mechanical damage. Change rate from initial value Dielectric loss tangent Insulation resistance As per 4.22 of JIS C 5101-1 As per 4.14 of JIS C 5101-10 Within +/−7.5% AN Test temperature : 60+/−2°C Relative humidity : 90 to 95% Rated voltage 25V,16V,10V Within +/−12.5% Voltage : Rated voltage CN Test time : 500 +24/−0 h Rated voltage Within +/−25.0% Initial measurements prior to test shall 6.3V be made after the voltage FN Within +/−30% pre-conditioning specified in Remarks (2). AN tan δ < − 0.3% Final measurements shall be made after the specimens have been left at room Less than 200% of temperature as per Table3. CN initial spec. Table3 Less than 150% of FN initial spec. CharacTime teristic Not less than 500MΩ or AN 24+/−2 h 25MΩ µF, whichever is less. (For products with rated voltage less CN, FN 48+/−4 h than 16V, it is not less than 500mΩ or 5MΩ µF, whichever is less.) 6/10 MCH43 Ceramic capacitors No. Items 15 Heat life test Performance Appearance Without mechanical damage. AN Change rate from initial value CN Dielectric loss tangent Insulation resistance Within +/−3.0% Test Method (As per JIS C 5101-1, JIS C 5101-10) As per 4.23 of JIS C 5101-1. As per 4.15 of JIS C 5101-10 Test Voltage temperature(°C) Rated voltage 25V,16V,10V Within +/−15% Rated voltage Within +/−25% 6.3V FN Within +/−30% AN tan δ < − 0.5% CN Less than 200% of initial spec. FN Less than 150% of initial spec. Not less than 1000MΩ or 50MΩ µF, whichever is less. (For products with rated voltage less than 16V, it is not less than 1000mΩ or 10MΩ µF, whichever is less.) Test time (h) AN 125 200% Rated voltage 1000 +48/−0 CN 85 (B X5R) 1000 +48/−0 FN 85 200% Rated voltage 200% Rated voltage 1000 +48/−0 Initial measurements prior to test shall be made after the voltage pre-conditioning specified in Remarks (2). Final measurements shall be made after the specimens have been left at room temperature Table3 Characteristic AN CN, FN Time 24+/−2 h 48+/−4 h [Remarks] Pre-conditioning If specified in test method of as per 3(Performance and test merhod), capacitors of CN, FN characteristics shall be pre-conditionded as follows. (1) Thermal pre-conditioning Prior to initial measurements, specimens shall be conditioned at a temperature of 150 0/−10°C for a period of 1hr., and shall be allowed to stabilize at room temperature for 48+/−4h (2) Voltage pre-conditioning Prior to initial measurements, voltage specified as a test condition shall be applied to specimens for a period of 1hr., and the specimens shall be allowed to stabilize at room temperature for 48+/−4h <Test jig> Soldering Glass epoxy substrate 7/10 MCH43 Ceramic capacitors zPackaging specifications Taping dimensions Reel dimensions t φJ E 14.0 + −1.5 A D B G t1 H P : Plastic tape Pulling direction C Symbol D E H G F t J Symbol MCH43 t1 Plastic 0.6 12.0 5.5 1.75 8.0 2.0 4.0 φ1.5 Dimensions +/ −0.3 +/ −0.05 +/ −0.1 +/ −0.1 +/ −0.05 +/ −0.1 +0.1/ −0 MAX. Style +0 φ180 −1.5 F φ60.0+1.0 −0 φ13.0 + − 0.2 C 6.5 MAX. Label pasting (Unit : mm) A B 3.6 4.9 As per EIAJ ET−7200A (Unit : mm) (Unit : mm) (1) The quantity for one reel is as bellows. Kind of reel Series φ180 reel MCH43 Plastic tape Quantity Symbol 500 pcs. P (2) When the tape is pulled out towards the operator with the cover tape facing upward, the feeding holes shall be found on the right portion of the tape. (3) Specification of beginning and ending of the tape are as follows. Ending(reel's center) Beginning(reel's round) : Approx. Over 160mm (no chips) : Approx. Over 160mm (no chips) : Approx. 240mm (cover tape only) (4) No juncture of tape shall be allowed. (5) The share strength of tape shall be more than 5N at the break down strength. (6) The peel strength of the cover tape shall be 0.1 to 0.7(N) when the cover tape are peeled 0 to 15 degree from the surface. (7) The number of missing components shall not exceed 0.1% of the total number of components (marked number) or one whichever is the larger, and no consecutive missing exceeding two is allowed. (8) The reels made from resin shall be used, as per EIAJ ET-7200A. zMarking No marking shall be performed on the chip. Trademark, parts number, quantity, lot No. , and country of origin shall be labeled on each reel. zNumbering system for LOT No. Example 03 (1) 01 (2) A0001 (3) F (4) (1) The end of the Christian Era < two digits> of production finish. (2) Week in completing part of production finish. (3) Manufacture continuity number. (4) The symbol of manufacturing plant. 8/10 MCH43 Ceramic capacitors zLabel expression The Figure below is label expression < Label Example > Part Number : MCH435AN104JP ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ Part Number Division cord Quantity Lot No. The Country of origin Inspector QR code Trademark zPacking method 1) φ180mm Reel EIAJ cole B' 2 C' (reel) Label A' [width of 9mm : 5reel] 1 A (interior box of R-26) Packing slip B C (R-26) 9/10 MCH43 Ceramic capacitors < Packaging unit > Symbol Quantity of reel in interior box Quantity of reel in box of R-26 K Dimensions R-26 3 12 Packaging interior box ofR-26 A (A’) 195 185 B (B’) 255 60 C (C’) 190 185 (Unit : mm) < Appearance > Carton < Accumulation > You must do accumulation by ten boxes < Packaging slip > 1. 2. 3. 4. 5. Customer Parts number Quantity Box quantity Trade mark 10/10 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1