FOSLINK FSP2161K25AD 1.5a low voltage low dropout cmos regulator Datasheet

1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
FSP2161
„
FEATURES
„
z
z
z
z
z
z
z
Low-Dropout Regulator Supports Input Voltages
Down to 1.4V
Output Voltage Available in 0.9V, 1.0V, 1.2V, 1.5V,
1.8V, 2.5V,2.8V,2.85V,3.0V, 3.3V
Stable with a Ceramic Output Capacitor of
1.0uF or Higher
Low Dropout Voltage:150mV at 1.5A
Low Quiescent Current
Over Temperature Shutdown
Short Circuit Protection
Low Temperature Coefficient
Standard TO252 and TO263 Packages
„
APPLICATIONS
The FSP2161 is a 1.5A CMOS LDO regulator that
features a low quiescent current, ultra low input, output
and dropout voltages, as well as over temperature
shutdown. It is available in TO252 and TO263
packages. The fixed output voltage of the FSP2161 is
set at the factory and trimmed to ±2%. The FSP2161 is
stable with a ceramic output capacitor of 1.0uF or
higher.
This family of regulators can provide either a
stand-alone power supply solution or act as a post
regulator for switch mode power supplies. They are
particularly well suited for applications requiring low
input and output voltage
z
z
z
z
z
z
z
z
DSP, FPGA, and Microprocessor Power Supplies
1.2V Core Voltage for DSPs
SATA Power Supply
LCD TV/ Monitors
Wireless Devices
Communication Devices
Portable Electronics
Post Regulator for SMPS
„
PIN CONFIGURATION
z
z
1) TO252
„
(Top View)
TO252
1
2
3
1/12
2) TO263
(Top View)
PIN DESCRIPTION
Pin Number
„
GENERAL DESCRIPTION
TO263
1
3
5
2
4
Pin Name
Pin Function
VIN
GND
VOUT
EN
PWRGD
Input
Ground
Output
Enable pin
Power good
BLOCK DIAGRAM
2007-12-6
1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
FSP2161
„
TYPICAL APPLICATIONS CIRCUITS
„
ABSOLUTE MAXIMUM RATINGS
Parameter
Input Supply Voltage
Maximum Output Current
Rating
+4
PD/(VIN-VO)
Unit
V
Output Pin Voltage
-0.3 to VIN+0.3
V
Internal Power Dissipation
1200
mW
Junction to Case Thermal Resistance (θJC)
7
℃/ W
Junction to Ambient Thermal Resistance (θJA)
90
℃/ W
Operating temperature
-40 to 85
°C
Operating Junction Temperature
-40 to 125
°C
Storage Temperature
-65 to 150
°C
Maximum Junction Temperature
150
°C
Lead Temperature (Soldering, 5 sec)
300
°C
Note: These are stress ratings only and functional operation is not implied. Exposure to absolute maximum ratings
for prolonged time periods may affect device reliability. All voltages are with respect to ground.
„
2/12
RECOMMENDED OPERATING CONDITIONS
Parameter
Input Supply Voltage
Operating temperature
Rating
1.4 to 3.6
-40 to 85
Unit
V
°C
Operating Junction Temperature
-40 to 125
°C
2007-12-6
1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
„
FSP2161
ELECTRICAL CHARACTERISTICS
(VOUT = VIN + 0.5V, CIN = 1µF, CO = 2.2µF, TA= 25°C unless otherwise specified.)
PARAMETER
SYMBOL
Input Voltage
Output Voltage Accuracy
Short Circuit Current
Ground Current
Quiescent Current
VIN
VO
ISC
IGND
IQ
Line Regulation
LNR
Load Regulation Error
Temperature Coefficient
Over Temperature Shutdown
Over Temperature Hystersis
Power Supply Ripple Rejection
LDR
TC
OTS
OTH
PSRR
TEST CONDITIONS
MIN
IO= 100mA
Note1
-2
IO = 100mA
Vo =1.5V
IO = 500mA
Dropout Voltage
VDROP
IO = 1.5A
Output Noise
Vn
MAX
UNIT
3.6
+2
V
%
A
90
600
150
µA
µA
0.5
1
0.5
1
2
1.2V ≤ VO < 2.5V
VO ≥ 2.5V
0.5
40
150
50
55
55
35
330
220
50
40
500
400
200
150
VO= 0.9V
330
500
VO= 1.0V
220
400
1.2V ≤ VO < 2.5V
150
350
VO ≥ 2.5V
120
300
VO < 0.3V
IO= 1mA to 1.5A
IO= 0mA
IO= 10mA, VO ≤ 2.5V
VIN =VO + 0.5V to VO + 1.5V
IO= 10mA, VO>2.5V
VIN = 3.3V to 3.6V
IO = 1mA to 1.5A
f=100Hz
f= 1KHz
f= 10KHz
VO= 0.9V
VO= 1.0V
f = 10Hz to 100kHz
TYP
1.0
%/V
40
%/A
ppm/°C
°C
°C
dB
mV
µVRMS
Note 1:The minimum input voltage of the FSP2161 is determined by output voltage and dropout voltage. The
minimum input voltage is defined as:
VIN(MIN)=VO+VDROP
3/12
2007-12-6
1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
FSP2161
„
APPLICATION INFORMATION
The FSP2161 family of low-dropout (LDO) regulators have several features that allow them to apply to a wide range
of applications. The family operates with very low input voltage (1.4V) and low dropout voltage (typically 150mV at
full load), making it an efficient stand-alone power supply or post regulator for battery or switch mode power supplies.
The 1.5A output current make the FSP2161 family suitable for powering many microprocessors and FPGA supplies.
The FSP2161 family also has low output noise (typically 40µVRMS with 2.2µF output capacitor), making it ideal for
use in telecom equipment.
External Capacitor Requirements
A 2.2µF or larger ceramic input bypass capacitor, connected between VIN and GND and located close to the
FSP2161, is required for stability. A 1.0uF minimum value capacitor from VO to GND is also required. To improve
transient response, noise rejection, and ripple rejection, an additional 10µF or larger, low ESR capacitor is
recommended at the output. A higher-value, low ESR output capacitor may be necessary if large, fast-rise-time load
transients are anticipated and the device is located several inches from the power source, especially if the minimum
input voltage of 1.4 V is used.
Regulator Protection
The FSP2161 features internal current limiting, thermal protection and short circuit protection. During normal
operation, the FSP2161 limits output current to about 3A. When current limiting engages, the output voltage scales
back linearly until the over current condition ends. While current limiting is designed to prevent gross device failure,
care should be taken not to exceed the power dissipation ratings of the package. If the temperature of the device
exceeds 150°C, thermal-protection circuitry will shut down. Once the device has cooled down to approximately 50°C
below the high temp trip point, regulator operation resumes. The short circuit current of the FSP2161 is about 1A
when its output pin is shorted to ground.
Thermal Information
The amount of heat that an LDO linear regulator generates is:
PD=(VIN-VO)IO.
All integrated circuits have a maximum allowable junction temperature (TJ max) above which normal operation is not
assured. A system designer must design the operating environment so that the operating junction temperature (TJ)
does not exceed the maximum junction temperature (TJ max). The two main environmental variables that a
designer can use to improve thermal performance are air flow and external heatsinks. The purpose of this
information is to aid the designer in determining the proper operating environment for a linear regulator that is
operating at a specific power level.
In general, the maximum expected power (PD(max)) consumed by a linear regulator is computed as:
Where:
VI (avg) is the average input voltage.
VO(avg) is the average output voltage.
IO(avg) is the average output current.
I(Q) is the quiescent current.
For most LDO regulators, the quiescent current is insignificant compared to the average output current; therefore,
the term VI(avg) xI(Q) can be neglected. The operating junction temperature is computed by adding the ambient
temperature (TA) and the increase in temperature due to the regulator's power dissipation. The temperature rise is
computed by multiplying the maximum expected power dissipation by the sum of the thermal resistances between
the junction and the case (RθJC), the case to heatsink (RθCS), and the heatsink to ambient (RθSA). Thermal
resistances are measures of how effectively an object dissipates heat. Typically, the larger the device, the more
surface area available for power dissipation so that the object's thermal resistance will be lower.
4/12
2007-12-6
1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
„
5/12
TYPICAL PERFORMANCE CHARACTERISTICS
FSP2161
2007-12-6
1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
FSP2161
„
6/12
TYPICAL PERFORMANCE CHARACTERISTICS(CONTINUED)
2007-12-6
1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
FSP2161
„
7/12
TYPICAL PERFORMANCE CHARACTERISTICS(CONTINUED)
2007-12-6
1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
FSP2161
„
8/12
TYPICAL PERFORMANCE CHARACTERISTICS(CONTINUED)
2007-12-6
1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
FSP2161
„
ORDERING INFORMATION
FSP2161XXXX
Package Type:
D: TO252
K: TO263
„
Output Voltage:
33: 3.3V
30: 3.0V
285: 2.85V
28: 2.8V
25: 2.5V
18: 1.8V
15: 1.5V
12: 1.2V
10: 1.0V
09: 0.9V
Temperature Grade:
Packing:
A: Tape & Reel D: -40~85℃
MARKING INFORMATION
(1) TO252
(2) TO263
Logo
2161-VV
YYWWXX
9/12
Part Number:
2161-09: 0.9V
2161-10: 1.0V
2161-12: 1.2V
2161-15: 1.5V
2161-18: 1.8V
2161-25: 2.5V
2161-28: 2.8V
2161-285: 2.85V
2161-30: 3.0V
2161-33: 3.3V
Logo
2161-VV
YYWWXX
Part Number:
2161-09: 0.9V
2161-10: 1.0V
2161-12: 1.2V
2161-15: 1.5V
2161-18: 1.8V
2161-25: 2.5V
2161-28: 2.8V
2161-285: 2.85V
2161-30: 3.0V
2161-33: 3.3V
Internal Code
Internal Code
Date Code:
YY: Year (01=2001)
WW: Nth week (01~52)
Date Code:
YY: Year (01=2001)
WW: Nth week (01~52)
2007-12-6
1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
FSP2161
„
PACKAGE INFORMATION
(1) TO252
Symbol
A
B
C
D
E
F
S
G
H
J
K
L
M
R
10/12
Min.
6.40
5.20
6.80
2.20
0.70
0.60
0.50
2.20
0.45
0
0.90
5.40
0.80
Dimensions In Millimeters
Nom.
6.60
5.35
7.00
2.50
2.30REF
0.80
0.75
0.60
2.30
0.50
0.07
1.20
5.60
1.00
Max.
6.80
5.50
7.20
2.80
0.90
0.90
0.70
2.40
0.55
0.15
1.50
5.80
1.20
Dimensions In Inches
Nom.
0.264
0.214
0.280
0.100
0.092REF
0.028
0.032
0.024
0.030
0.020
0.024
0.088
0.092
0.018
0.020
0
0.003
0.036
0.048
0.216
0.224
0.032
0.040
Min.
0.256
0.208
0.272
0.088
2007-12-6
Max.
0.272
0.220
0.288
0.112
0.036
0.036
0.028
0.096
0.022
0.006
0.060
0.232
0.048
1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
FSP2161
2) TO263
10.90
E
9.10
L2
D
15.70
L
2.50
1.00
e
B
1.70
Land Pattern Recommendation (Unit: mm)
A
C2
C
L1
Symbol
A
B
C
C2
D
E
e
L
L1
L2
11/12
Min.
4.07
0.51
0.36
1.14
8.20
9.65
1.57
14.45
1.78
Dimensions In Millimeters
Nom.
Max.
4.46
4.85
0.84
1.02
0.50
0.74
1.27
1.65
9.15
9.65
10.16
10.67
1.71
1.85
15.24
15.88
2.54
2.79
2.92
Min.
0.163
0.020
0.014
0.046
0.328
0.386
0.063
0.578
0.071
Dimensions In Inches
Nom.
0.176
0.033
0.020
0.050
0.360
0.400
0.068
0.600
0.100
2007-12-6
Max.
0.194
0.041
0.030
0.066
0.380
0.427
0.074
0.635
0.110
0.115
1.5A LOW VOLTAGE LOW DROPOUT CMOS REGULATOR
FSP2161
12/12
2007-12-6
Similar pages