VIPER Remote Control Systems • 433MHz FM Technology • 1 – 4 Channels each 1000W Rated • upto 150metres Range • 12-30Vdc / 230Vac supply • Waterproof (IP68) • High Security RF Protocol • 4 Relays 5A @ 230Vac • Outputs Momentary or Latching • Any Switch Map to Any Relay Output • Systems supplied ’ready to Go’ • EMC / FCC Compliant for Europe / USA Applications • General Purpose Remote Switching • Garage Doors • Electric Gates, Shutters • All known Lighting types (LED, fluorescent, halogen, tungsten, xenon; basically all lighting types). • Access Control Description Housed in a rugged IP68 weatherproof enclosure, The VIPER system is ideally suited to any outside Remote switch requirement. Each receiver has 4 relays, using the ‘easy-learn’ process each relay can be controlled from any switch on any transmitter. Installation is by screw terminals to the power supply, and the output relay contacts. The output relays are activated by the button press on the transmitter encoder. DS VIPER-2 ©2009 REG No 277 4001, Lewes, England. Page 1 VIPER Remote Control Systems Systems Part Numbers Operating from 12-30Vdc Receiver Range** System 1 channel Power Supply 12-30Vdc (Metres) 150 VIPER-S2 System 2 channel 12-30Vdc 150 VIPER-S4 System 4 channel 12-30Vdc 150 Part Number Description VIPER-S1 Systems Operating from 230Vac (see DS-VIPERMAINS) Receiver Range** System 1 channel Power Supply 230Vac (Metres) 150 System 2 channel 230Vac 150 Part Number Description VIPER-S1M VIPER-S2M **Range stated is optimum, direct line of sight. In worst conditions this can be reduced by over 50% Additional Transmitters Transmitters ship with; Wall Mounting Cradle, Part Number Description FIREFLY-TX1 Transmitter 1 switch FIREFLY-TX2 Transmitter 2 switch FIREFLY-TX4 Transmitter 4 switch FIREFLY-TX8 Transmitter 8 switch FIREFLY-TX16 Transmitter 16 switch (8Sw + Shift Key) FIREFLY -TX-IPKIT ’O’ Ring, Seals Transmitter to IP68 Custom Version To create a custom version requires just a Sticker! Please contact Sales for further info. DS VIPER-2 and Lanyard ©2009 REG No 277 4001, Lewes, England. Page 2 VIPER Remote Control Systems Data Outputs Each output relay provides an isolated switch. Connections are Common (COM), Normally Open (NO) and Normally Closed (NC). NC COM NO NC COM NO Relay Connections when Transmitter NOT Operating Relay Connections when Transmitter OPERATING Installation Below is a simple example showing one possible way to wire a relay in order to give switched power to an external load: When the relay is energised the ‘COM’ connects to ’NO’ and power is applied to the Load. R F Solutions Ltd., Unit 21, Cliffe Industrial Estate, Lewes, E. Sussex. BN8 6JL. England. Email : [email protected] Tel: +44 (0)1273 898 000 DS VIPER-2 http://www.rfsolutions.co.uk Fax: +44 (0)1273 480 661 ©2009 REG No 277 4001, Lewes, England. Page 3 VIPER Remote Control Systems Pairing a Transmitter to a Receiver Each transmitter has a unique identity. Each time a transmitter Switch is operated, it emits a secure RF signal. The Receiver can learn this signal and allocate to any of its outputs. The only limitation is that each receiver has a maximum memory for upto 40 pairings, these can be from the same or any number of transmitters. Hint: the same transmitter may be taught to different receivers to create ‘master keys’. VIPERVIPER-S1 / VIPERVIPER-S2 / VIPERVIPER-S3 (12(12-30Vdc Receivers) To Learn a New Transmitter switch follow this procedure Any transmitter button can be learnt to one or many of the receiver output relays. Each button must be learnt to each relay individually by following this procedure: 1. Select the receiver output relay to learn to: 2. Briefly press the receiver Learn switch (S2) once 3. The Learn LED will flash once to indicate output relay 1 is selected 4. After the LED stops flashing, press the Learn switch again to select the next relay channel 5. Repeat step 2 until the required output relay is selected. 6. Press the button on the transmitter you want to learn to the relay output. 7. The Learn LED will then illuminate, press the same transmitter button again. 8. The Learn LED will then flash to indicate learning is complete. 9. The transmitter button will now operate the relay. Erasing Receivers Memory 1. Press and hold the receiver Learn Switch for approx 10 seconds. 2. When the Learn LED turns OFF all memory is erased NOTE: You cannot erase individual Tx encoders Configuring Receiver Outputs The jumper links configure the outputs to be Momentary or Latching. The jumper links are made / removed by the small link ‘cap’ placed over the pin header. Link Positions LK1 LK2 Closed Closed RLY 1 Mom Relay Outputs RLY 2 RLY 3 Mom Mom RLY 4 Mom Closed Open Mom Mom Latch Latch Open Open Closed Mom Latch Latch Latch Open Latch Latch Latch Latch (The configuration shown in the picture above represents the third row of the table) DS VIPER-2 ©2009 REG No 277 4001, Lewes, England. Page 4 VIPER Remote Control Systems VIPERVIPER-S1M / VIPER S2M (230Vac Powered Receivers) Please Note: During Learn and Erase the relays operate at high speed. They should be isolated from sensitive equipment during this process. To Pair a Transmitter button to receiver Output Relay #1 1. Apply power the receiver and wait 10secs for the unit to enter ‘normal operation’ mode. 2. Switch the receiver unit OFF and then ON again in ~1sec intervals FOUR times finally leaving the unit powered. 3. After 5 seconds the receiver emits a single ‘buzz’ The unit is now in ‘learn’ Mode 5. Press the chosen transmitter button. 6. The receiver will acknowledge by sounding the a single ’buzz’ 7. Press the same transmitter button again, to confirm OK. The receiver will “buz” again to confirm. 8. Learn Process complete. After 10 seconds the unit will return to ‘normal operation’ mode. To Pair a Transmitter button to receiver Output Relay #2 1. Apply power the receiver and wait 10secs for the unit to enter ‘normal operation’ mode. 2. Switch the receiver unit OFF and then ON again in ~1sec intervals SIX times finally leaving the unit powered. 3. After 5 seconds the receiver emits a double ‘buzz’ The unit is now in ‘learn’ Mode 5. Press the chosen transmitter button. 6. The receiver will acknowledge by sounding the a double ’buzz’ 7. Press the same transmitter button again, to confirm OK. The receiver will double “buzz” again to confirm. 8. Learn Process complete. After 10 seconds the unit will return to ‘normal operation’ mode. Erasing Receivers Memory 1. Power the receiver unit up and wait 10 seconds for the unit to enter ‘normal operation’ mode. 2. Switch the unit off and then on again at ~1 second intervals TEN times, leaving the unit powered. 3. Wait 5 seconds until a ‘clicking’ sound is heard for a period of 10 seconds. 4. Wait 10 seconds for the receiver unit to return to ‘normal’ mode 5. The unit has now erased all encoder data. NOTE: You cannot erase individual Tx encoders Configuring Receiver Outputs The jumper links configure the outputs to be Momentary or Latching. The jumper links are made/removed by the small link ‘cap’ placed over the pin header. Link Positions - Relay Outputs LK1 Open Relay #1 Mom LK2 Open Relay #2 Mom Closed Latch Closed Latch DS VIPER-2 (the above image shows, RLY2 Momentary, RLY1 Latched) ©2009 REG No 277 4001, Lewes, England. Page 5 VIPER Remote Control Systems Technical Specifications Transmitters: FIREFLYFIREFLY-TXn Enclosure Rating: Standard IPx8 Battery Type: CR2032 (supplied) Dimensions: 90 x 54 x 27 mm Changing the Battery: Remove the six fixing screws, remove battery and replace note polarity Electrical Characteristics Min Supply Voltage Typical Max Units 3V V Supply Current Frequency: mA FireFLY: Wideband RF Output Power (ERP) @ 433 MHz 432.90 433.920 434.10 MHz - 3 10 mW Receiver Decoder Enclosure Rating Dimensions Storage Temperature: IP68 130 x 112 x 42 mm (not including antenna) -10 to +70o Celsius. Operating Temperature: -10 to +50o Celsius. ELECTRICAL CHARACTERISTICS MIN Supply Voltage for +12 v 10.5 Relay Rating* (230Vac) RLY1-4 Supply Current : TYPICAL 5 Quiescent MAX DIMENSION 30 Vdc 12 A 100 mA mS 300 MS 10 All relays operating* Time delay from Tx on Switch to Rx Relay operation Time delay from Tx sw relax to Rx Relay release 140 *The relay contacts in this unit are for functional use only and must not be used for isolation purposes R F Solutions Ltd., Unit 21, Cliffe Industrial Estate, Lewes, E. Sussex. BN8 6JL. England. Email : [email protected] Tel: +44 (0)1273 898 000 DS VIPER-2 http://www.rfsolutions.co.uk Fax: +44 (0)1273 480 661 ©2009 REG No 277 4001, Lewes, England. Page 6