ON NCV551SN32T1 150 ma cmos low iq low−dropout voltage regulator Datasheet

NCP551, NCV551
150 mA CMOS Low Iq
Low−Dropout Voltage
Regulator
The NCP551 series of fixed output low dropout linear regulators are
designed for handheld communication equipment and portable battery
powered applications which require low quiescent. The NCP551
series features an ultra−low quiescent current of 4.0 mA. Each device
contains a voltage reference unit, an error amplifier, a PMOS power
transistor, resistors for setting output voltage, current limit, and
temperature limit protection circuits.
The NCP551 has been designed to be used with low cost ceramic
capacitors and requires a minimum output capacitor of 0.1 mF. The
device is housed in the micro−miniature TSOP−5 surface mount
package. Standard voltage versions are 1.5, 1.8, 2.5, 2.7, 2.8, 2.9, 3.0,
3.1, 3.2, 3.3, and 5.0 V. Other voltages are available in 100 mV steps.
•
1
TSOP−5
(SOT23−5, SC59−5)
SN SUFFIX
CASE 483
Low Quiescent Current of 4.0 mA Typical
Maximum Operating Voltage of 12 V
Low Output Voltage Option
High Accuracy Output Voltage of 2.0%
Industrial Temperature Range of −40°C to 85°C
(NCV551, TA = −40°C to +125°C)
NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
Pb−Free Packages are Available
Typical Applications
• Battery Powered Instruments
• Hand−Held Instruments
• Camcorders and Cameras
Vin
1
GND
2
Enable
3
5 Vout
xxxAYWG
G
•
5
PIN CONNECTIONS AND
MARKING DIAGRAM
Features
•
•
•
•
•
http://onsemi.com
4 N/C
(Top View)
xxx = Specific Device Code
A
= Assembly Location
Y
= Year
W = Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
Vin
1
5
Thermal
Shutdown
Vout
Driver w/
Current
Limit
Enable
ON
3
OFF
GND
2
Figure 1. Representative Block Diagram
© Semiconductor Components Industries, LLC, 2006
November, 2006 − Rev. 14
1
Publication Order Number:
NCP551/D
NCP551, NCV551
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
1
Vin
Description
2
GND
3
Enable
4
N/C
No Internal Connection.
5
Vout
Regulated output voltage.
Positive power supply input voltage.
Power supply ground.
This input is used to place the device into low−power standby. When this input is pulled low, the
device is disabled. If this function is not used, Enable should be connected to Vin.
MAXIMUM RATINGS
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
Rating
Symbol
Value
Unit
Input Voltage
Vin
0 to 12
V
Enable Voltage
VEN
−0.3 to Vin +0.3
V
Output Voltage
Vout
−0.3 to Vin +0.3
V
Power Dissipation
PD
Internally Limited
W
Operating Junction Temperature
TJ
+150
°C
TA
−40 to +85
−40 to +125
°C
Tstg
−55 to +150
°C
Operating Ambient Temperature
NCP551
NCV551
Storage Temperature
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL−STD−883, Method 3015
Machine Model Method 200 V
2. Latchup capability (85°C) "100 mA DC with trigger voltage.
THERMAL CHARACTERISTICS
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
Rating
Junction−to−Ambient
PSIJ−Lead 2
NOTE:
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
Symbol
Test Conditions
Typical Value
Unit
RqJA
1 oz Copper Thickness, 100 mm2
250
°C/W
1 oz Copper Thickness, 100 mm2
68
°C/W
Single component mounted on an 80 x 80 x 1.5 mm FR4 PCB with stated copper head spreading area. Using the following
boundary conditions as stated in EIA/JESD 51−1, 2, 3, 7, 12.
http://onsemi.com
2
NCP551, NCV551
ELECTRICAL CHARACTERISTICS
(Vin = Vout(nom.) + 1.0 V, VEN = Vin, Cin = 1.0 mF, Cout = 1.0 mF, TJ = 25°C, unless otherwise noted.)
Characteristic
Symbol
Output Voltage (TA = 25°C, Iout = 10 mA)
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
2.9 V
3.0 V
3.1 V
3.2 V
3.3 V
5.0 V
Vout
Output Voltage (TA = Tlow to Thigh, Iout = 10 mA)
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
2.9 V
3.0 V
3.1 V
3.2 V
3.3 V
5.0 V
Vout
Min
Typ
Max
1.455
1.746
2.425
2.646
2.744
2.842
2.940
3.038
3.136
3.234
4.90
1.5
1.8
2.5
2.7
2.8
2.9
3.0
3.1
3.2
3.3
5.0
1.545
1.854
2.575
2.754
2.856
2.958
3.060
3.162
3.264
3.366
5.10
1.440
1.728
2.400
2.619
2.716
2.813
2.910
3.007
3.104
3.201
4.850
1.5
1.8
2.5
2.7
2.8
2.9
3.0
3.1
3.2
3.3
5.0
1.560
1.872
2.600
2.781
2.884
2.987
3.090
3.193
3.296
3.399
5.150
Unit
V
V
Line Regulation (Vin = Vout + 1.0 V to 12 V, Iout = 10 mA)
Regline
−
10
30
mV
Load Regulation (Iout = 10 mA to 150 mA, Vin = Vout + 2.0 V)
Regload
−
40
65
mV
Output Current (Vout = (Vout at Iout = 100 mA) −3%)
1.5 V−2.0 V (Vin = 4.0 V)
2.1 V−3.0 V (Vin = 5.0 V)
3.1 V−4.0 V (Vin = 6.0 V)
4.1 V−5.0 V (Vin = 8.0 V)
Io(nom.)
150
150
150
150
−
−
−
−
−
−
−
−
Dropout Voltage (Iout = 10 mA, Measured at Vout −3.0%)
1.5 V, 1.8 V, 2.5 V
2.7 V, 2.8 V, 2.9 V, 3.0 V, 3.1 V, 3.2 V, 3.3 V, 5.0 V
Vin−Vout
−
−
130
40
220
150
−
−
0.1
4.0
1.0
8.0
−
"100
−
1.3
−
−
−
−
0.3
160
160
160
160
350
350
350
350
600
600
600
600
Quiescent Current
(Enable Input = 0 V)
(Enable Input = Vin, Iout = 1.0 mA to Io(nom.))
IQ
Output Voltage Temperature Coefficient
Tc
Enable Input Threshold Voltage
(Voltage Increasing, Output Turns On, Logic High)
(Voltage Decreasing, Output Turns Off, Logic Low)
mA
mV
mA
V
Vth(en)
Output Short Circuit Current (Vout = 0 V)
1.5 V−2.0 V (Vin = 4.0 V)
2.1 V−3.0 V (Vin = 5.0 V)
3.1 V−4.0 V (Vin = 6.0 V)
4.1 V−5.0 V (Vin = 8.0 V)
mA
Iout(max)
3. Maximum package power dissipation limits must be observed.
TJ(max) * TA
PD +
RqJA
4. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
5. NCP551
Tlow = −40°C
Thigh = +85°C
NCV551
Tlow = −40°C
Thigh = +125°C.
http://onsemi.com
3
ppm/°C
NCP551, NCV551
DEFINITIONS
Load Regulation
Line Regulation
The change in output voltage for a change in output
current at a constant temperature.
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse technique such that the average
chip temperature is not significantly affected.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 3% below its
nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Line Transient Response
Typical over and undershoot response when input voltage
is excited with a given slope.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 160°C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Maximum Power Dissipation
The maximum total dissipation for which the regulator
will operate within its specifications.
Quiescent Current
The quiescent current is the current which flows through
the ground when the LDO operates without a load on its
output: internal IC operation, bias, etc. When the LDO
becomes loaded, this term is called the Ground current. It is
actually the difference between the input current (measured
through the LDO input pin) and the output current.
Maximum Package Power Dissipation
The maximum power package dissipation is the power
dissipation level at which the junction temperature reaches
its maximum operating value, i.e. 125°C. Depending on the
ambient power dissipation and thus the maximum available
output current.
http://onsemi.com
4
NCP551, NCV551
3.35
3.45
Vout = 3.3 V
3.3
GROUND CURRENT (mA)
GROUND CURRENT (mA)
Vout = 2.8 V
3.25
3.2
3.15
3.1
3.05
3.35
3.3
3.25
3.2
3.15
0
25
50
75
100
125
150
0
75
100
125
Figure 2. Ground Pin Current versus
Output Current
Figure 3. Ground Pin Current versus
Output Current
4
3.5
3.5
3
2.5
2
1.5
Vout(nom) = 2.8 V
Iout = 25 mA
1
0.5
150
3
2.5
2
1.5
Vout(nom) = 3.3 V
Iout = 25 mA
1
0.5
0
0
2
4
6
8
10
12
0
14
2
4
6
8
10
12
Vin, INPUT VOLTAGE (VOLTS)
Vin, INPUT VOLTAGE (VOLTS)
Figure 4. Ground Pin Current versus
Input Voltage
Figure 5. Ground Pin Current versus
Input Voltage
Vin, INPUT
VOLTAGE (V)
0
8
6
4
OUTPUT VOLTAGE
DEVIATION (mV)
Vin, INPUT
VOLTAGE (V)
50
Iout, OUTPUT CURRENT (mA)
4
OUTPUT VOLTAGE
DEVIATION (mV)
25
Iout, OUTPUT CURRENT (mA)
GROUND PIN CURRENT (mA)
GROUND PIN CURRENT (mA)
3.4
Vin = 3.8 V to 4.8 V
Vout = 2.8 V
Cout = 1 mF
Iout = 10 mA
400
200
14
6
4
Vin = 3.8 V to 4.8 V
Vout = 2.8 V
Cout = 1 mF
Iout = 100 mA
400
200
0
−200
0
−400
−200
−600
−400
0
200
400
600
800
1000
1200 1400
1600
0
200
400
600
800
1000 1200 1400
TIME (ms)
TIME (ms)
Figure 6. Line Transient Response
Figure 7. Line Transient Response
http://onsemi.com
5
160
Vin, INPUT
VOLTAGE (V)
6
4
Vin = 3.8 V to 4.8 V
Vout = 2.8 V
Cout = 1 mF
Iout = 150 mA
400
200
0
−200
0
200
400
800
600
1000
1200 1400
1600
0
200
400
600
800
1000 1200 1400 1600
TIME (ms)
TIME (ms)
Figure 8. Line Transient Response
Figure 9. Line Transient Response
Vin, INPUT
VOLTAGE (V)
Vin, INPUT
VOLTAGE (V)
200
−600
0
6
4
800
400
200
OUTPUT VOLTAGE
DEVIATION (mV)
Vin = 4.3 V to 5.3 V
Vout = 3.3 V
Cout = 1 mF
Iout = 100 mA
600
OUTPUT VOLTAGE
DEVIATION (mV)
Vin = 4.3 V to 5.3 V
Vout = 3.3 V
Cout = 1 mF
Iout = 10 mA
400
−400
−600
0
−200
6
4
Vin = 4.3 V to 5.3 V
Vout = 3.3 V
Cout = 1 mF
Iout = 150 mA
600
400
200
0
−200
−400
−400
−600
−600
300
500 700
900 1100 1300 1500 1700 1900
800
1200
2000
1600
Figure 10. Line Transient Response
Figure 11. Line Transient Response
Vout = 2.8 V
Cout = 10 mF
OUTPUT VOLTAGE
DEVIATION (mV)
0
0
−500
−1000
0
400
TIME (ms)
Iout = 3.0 mA − 150 mA
150
0
TIME (ms)
Iout, OUTPUT
CURRENT (mA)
100
Iout, OUTPUT
CURRENT (mA)
4
−200
−400
OUTPUT VOLTAGE
DEVIATION (mV)
6
OUTPUT VOLTAGE
DEVIATION (mV)
OUTPUT VOLTAGE
DEVIATION (mV)
Vin, INPUT
VOLTAGE (V)
NCP551, NCV551
1
2
3
4
5
6
7
8
9
Iout = 3.0 mA − 150 mA
Vout = 2.8 V
Cout = 10 mF
150
0
1000
500
0
−500
TIME (ms)
0
1
2
3
4
5
6
7
8
9
TIME (ms)
Figure 12. Load Transient Response ON
Figure 13. Load Transient Response OFF
http://onsemi.com
6
Iout, OUTPUT
CURRENT (mA)
Iout = 3.0 mA − 150 mA
Vout = 3.3 V
Cout = 10 mF
150
0
OUTPUT VOLTAGE
DEVIATION (mV)
OUTPUT VOLTAGE
DEVIATION (mV)
Iout, OUTPUT
CURRENT (mA)
NCP551, NCV551
1000
500
0
−500
0
1
2
3
4
5
6
7
8
9
Iout = 3.0 mA − 150 mA
Vout = 3.3 V
Cout = 10 mF
150
0
−500
−1000
0
1
2
3
TIME (ms)
7
8
9
ENABLE
VOLTAGE (V)
3
2
1
0
3
Co = 1 mF
Vin = 4.3 V
Vout = 3.3 V
RO = 3.3 k
VEN = 2.0 V
2
1
Vout, OUTPUT
VOLTAGE (V)
ENABLE
VOLTAGE (V)
6
Figure 15. Load Transient Response ON
3
Vout, OUTPUT
VOLTAGE (V)
5
TIME (ms)
Figure 14. Load Transient Response OFF
Co = 10 mF
0
0
200 400 600 800 1000 1200 1400 1600 1800 2000
2
1
0
3
Co = 1 mF
Vin = 3.8 V
Vout = 2.8 V
RO = 2.8 k
VEN = 2.0 V
2
1
Co = 10 mF
0
0
200 400 600 800 1000 1200 1400 1600 1800 2000
TIME (ms)
TIME (ms)
Figure 16. Turn−On Response
Figure 17. Turn−On Response
3
3.5
Vout, OUTPUT VOLTAGE (VOLTS)
Vout, OUTPUT VOLTAGE (VOLTS)
4
2.5
2
Vin = 0 V to 12 V
Vout(nom) = 2.8 V
Iout = 10 mA
Cin = 1 mF
Cout = 1 mF
VEN = Vin
1.5
1
0.5
0
3
2.5
Vin = 0 V to 12 V
Vout = 3.3 V
Iout = 10 mA
Cin = 1 mF
Cout = 1 mF
VEN = Vin
2
1.5
1
0.5
0
0
2
4
6
8
10
12
0
2
4
6
8
10
12
Vin, INPUT VOLTAGE (VOLTS)
Vin, INPUT VOLTAGE (VOLTS)
Figure 18. Output Voltage versus Input Voltage
Figure 19. Output Voltage versus Input Voltage
http://onsemi.com
7
NCP551, NCV551
APPLICATIONS INFORMATION
Thermal
A typical application circuit for the NCP551 series is
shown in Figure 20.
As power across the NCP551 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material, and also the ambient
temperature effect the rate of temperature rise for the part.
This is stating that when the NCP551 has good thermal
conductivity through the PCB, the junction temperature will
be relatively low with high power dissipation applications.
The maximum dissipation the package can handle is
given by:
Input Decoupling (C1)
A 0.1 mF capacitor either ceramic or tantalum is
recommended and should be connected close to the NCP551
package. Higher values and lower ESR will improve the
overall line transient response.
Output Decoupling (C2)
The NCP551 is a stable Regulator and does not require
any specific Equivalent Series Resistance (ESR) or a
minimum output current. Capacitors exhibiting ESRs
ranging from a few mW up to 3.0 W can thus safely be used.
The minimum decoupling value is 0.1 mF and can be
augmented to fulfill stringent load transient requirements.
The regulator accepts ceramic chip capacitors as well as
tantalum devices. Larger values improve noise rejection and
load regulation transient response.
PD +
If junction temperature is not allowed above the
maximum 125°C, then the NCP551 can dissipate up to
400 mW @ 25°C.
The power dissipated by the NCP551 can be calculated
from the following equation:
Enable Operation
Ptot + [Vin * Ignd (Iout)] ) [Vin * Vout] * Iout
The enable pin will turn on or off the regulator. These
limits of threshold are covered in the electrical specification
section of this data sheet. If the enable is not used then the
pin should be connected to Vin.
or
P ) Vout * Iout
VinMAX + tot
IGND ) Iout
If a 150 mA output current is needed then the ground
current from the data sheet is 4.0 mA. For an
NCP551SN30T1 (3.0 V), the maximum input voltage will
then be 5.6 V.
Hints
Please be sure the Vin and GND lines are sufficiently wide.
When the impedance of these lines is high, there is a chance
to pick up noise or cause the regulator to malfunction.
Set external components, especially the output capacitor,
as close as possible to the circuit, and make leads as short as
possible.
Battery or
Unregulated
Voltage
Vout
C1
TJ(max) * TA
RqJA
+
+
ON
OFF
Figure 20. Typical Application Circuit
http://onsemi.com
8
C2
NCP551, NCV551
Input
Input
Q1
R1
Q1
R2
R
Q2
Output
1
1.0 mF
R3
5
1.0 mF
2
3
1.0 mF
4
5
1.0 mF
2
3
Figure 21. Current Boost Regulator
4
Figure 22. Current Boost Regulator with
Short Circuit Limit
The NCP551 series can be current boosted with a PNP transistor. Resistor R in conjunction with VBE of the PNP determines
when the pass transistor begins conducting; this circuit is not
short circuit proof. Input/Output differential voltage minimum is
increased by VBE of the pass resistor.
Input
Output
1
Short circuit current limit is essentially set by the VBE of Q2 and
R1. ISC = ((VBEQ2 − ib * R2) / R1) + IO(max) Regulator
Output
1
5
1.0 mF
1.0 mF
2
Input
Output
Q1
1
Enable
3
4
R
1.0 mF
Output
1
1.0 mF
1.0 mF
2
3
5
5
4
11 V
1.0 mF
2
3
R
4
C
Figure 24. Input Voltages Greater than 12 V
A regulated output can be achieved with input voltages that
exceed the 12 V maximum rating of the NCP551 series with
the addition of a simple pre−regulator circuit. Care must be
taken to prevent Q1 from overheating when the regulated
output (Vout) is shorted to GND.
Figure 23. Delayed Turn−on
If a delayed turn−on is needed during power up of several voltages then the above schematic can be used. Resistor R, and
capacitor C, will delay the turn−on of the bottom regulator.
ORDERING INFORMATION
Device
NCP551SN15T1
NCP551SN15T1G
NCP551SN18T1
NCP551SN18T1G
NCP551SN25T1
NCP551SN25T1G
NCP551SN27T1
NCP551SN27T1G
Nominal
Output Voltage
Marking
Package
Shipping †
1.5
LAO
TSOP−5
3000 / Tape & Reel
1.5
LAO
TSOP−5
(Pb−Free)
3000 / Tape & Reel
1.8
LAP
TSOP−5
3000 / Tape & Reel
1.8
LAP
TSOP−5
(Pb−Free)
3000 / Tape & Reel
2.5
LAQ
TSOP−5
3000 / Tape & Reel
2.5
LAQ
TSOP−5
(Pb−Free)
3000 / Tape & Reel
2.7
LAR
TSOP−5
3000 / Tape & Reel
2.7
LAR
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NOTE: Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
6. NCV551 is qualified for automotive use.
http://onsemi.com
9
NCP551, NCV551
ORDERING INFORMATION
Nominal
Output Voltage
Marking
Package
Shipping †
NCP551SN28T1
2.8
LAS
TSOP−5
3000 / Tape & Reel
NCP551SN28T1G
2.8
LAS
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCP551SN29T1G
2.9
LJL
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCP551SN30T1
3.0
LAT
TSOP−5
3000 / Tape & Reel
NCP551SN30T1G
3.0
LAT
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCP551SN31T1G
3.1
LJM
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCP551SN32T1G
3.2
LIV
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCP551SN33T1
3.3
LAU
TSOP−5
3000 / Tape & Reel
NCP551SN33T1G
3.3
LAU
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCP551SN50T1
5.0
LAV
TSOP−5
3000 / Tape & Reel
NCP551SN50T1G
5.0
LAV
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCV551SN15T1
1.5
LFZ
TSOP−5
3000 / Tape & Reel
NCV551SN15T1G
1.5
LFZ
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCV551SN18T1
1.8
LGA
TSOP−5
3000 / Tape & Reel
NCV551SN18T1G
1.8
LGA
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCV551SN25T1
2.5
LGB
TSOP−5
3000 / Tape & Reel
NCV551SN25T1G
2.5
LGB
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCV551SN27T1
2.7
LGC
TSOP−5
3000 / Tape & Reel
NCV551SN27T1G
2.7
LGC
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCV551SN28T1
2.8
LGD
TSOP−5
3000 / Tape & Reel
NCV551SN28T1G
2.8
LGD
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCV551SN30T1
3.0
LGE
TSOP−5
3000 / Tape & Reel
NCV551SN30T1G
3.0
LGE
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCV551SN31T1G
3.1
LJR
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCV551SN32T1
3.2
LFR
TSOP−5
3000 / Tape & Reel
NCV551SN32T1G
3.2
LFR
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCV551SN33T1
3.3
LGG
TSOP−5
3000 / Tape & Reel
NCV551SN33T1G
3.3
LGG
TSOP−5
(Pb−Free)
3000 / Tape & Reel
NCV551SN50T1
5.0
LGF
TSOP−5
3000 / Tape & Reel
NCV551SN50T1G
5.0
LGF
TSOP−5
(Pb−Free)
3000 / Tape & Reel
Device
NOTE: Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
6. NCV551 is qualified for automotive use.
http://onsemi.com
10
NCP551, NCV551
PACKAGE DIMENSIONS
TSOP−5
CASE 483−02
ISSUE F
NOTE 5
2X
0.10 T
2X
0.20 T
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES
LEAD FINISH THICKNESS. MINIMUM LEAD
THICKNESS IS THE MINIMUM THICKNESS
OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
5. OPTIONAL CONSTRUCTION: AN
ADDITIONAL TRIMMED LEAD IS ALLOWED
IN THIS LOCATION. TRIMMED LEAD NOT TO
EXTEND MORE THAN 0.2 FROM BODY.
D 5X
0.20 C A B
5
1
4
2
3
M
B
S
K
L
DETAIL Z
G
A
DIM
A
B
C
D
G
H
J
K
L
M
S
DETAIL Z
J
C
0.05
SEATING
PLANE
H
T
MILLIMETERS
MIN
MAX
3.00 BSC
1.50 BSC
0.90
1.10
0.25
0.50
0.95 BSC
0.01
0.10
0.10
0.26
0.20
0.60
1.25
1.55
0_
10 _
2.50
3.00
SOLDERING FOOTPRINT*
0.95
0.037
1.9
0.074
2.4
0.094
1.0
0.039
0.7
0.028
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
11
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP551/D
Similar pages