AWT6301R Cellular CDMA 3.4 V/28 dBm Linear Power Amplifier Module Data Sheet - Rev 2.0 FEATURES • InGaP HBT Technology • High Efficiency: 40%, VMODE = 0 V 41%, VMODE = +2.85 V (no mode switching) • Low Quiescent Current: 50 mA • Low Leakage Current in Shutdown Mode: <1 µA • VREF = +2.85 V (+2.75 V Min Over Temp.) • Optimized for a 50 Ω System • Low Profile Surface Mount Package: 1.1mm • CDMA 1XRTT, 1xEV-DO Compliant • Pinout Enables Easy Phone Board Migration From 4 mm x 4 mm Package • RoHS Compliant Package, 250 oC MSL-3 M9 Package 8 Pin 3 x 3 x 1 mm Surface Mount Module APPLICATIONS • CDMA/EVDO Cell-band Wireless Handsets and Data Devices PRODUCT DESCRIPTION The AWT6301R meets the increasing demands for higher efficiency and linearity in CDMA1X handsets. The package pinout was chosen to enable handset manufacturers to switch from a 4mm x 4mm PA module with very few layout changes to the phone board. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-theart reliability, temperature stability, and ruggedness. Selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, serve to increase handset talk and standby time. The self contained 3 mm x 3 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency and linearity in a 50 Ω system. GND at slug (pad) VREF 8 GND 7 RFOUT 3 6 GND VCC1 4 5 VCC2 1 VMODE 2 RFIN Bias Control Figure 1: Block Diagram 10/2008 AWT6301R GND VREF 1 8 GND VMODE 2 7 RFOUT RFIN 3 6 GND VCC1 4 5 VCC2 GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VREF Reference Voltage 2 VMODE Mode Control 3 RFIN RF Input 4 VCC1 Supply Voltage 5 VCC2 Supply Voltage 6 GND Ground 7 RFOUT RF Output 8 GND Ground Data Sheet - Rev 2.0 10/2008 AWT6301R ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC ) With RF Drive DC Only 0 0 +5 +8 V Mode Control Voltage (VMODE) 0 +3.5 V Reference Voltage (VREF) 0 +3.5 V RF Input Power (PIN) - +10 dBm -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT COMMENTS Operating Frequency (f) 824 - 849 MHz Supply Voltage (VCC) +3.2 +3.4 +4.2 V Reference Voltage (VREF) +2.75 0 +2.85 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE) +2.5 0 +2.85 - +3.1 +0.5 V Low Bias Mode High Bias Mode RF Output Power (POUT) 27.5(1) 28.0 - dBm Case Temperature (TC) -30 - +85 °C CDMA The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at VCC = +3.2 V, POUT is derated by 0.5 dB. Data Sheet - Rev 2.0 10/2008 3 AWT6301R Table 4: Electrical Specifications - CDMA Operation with mode switching (TC = +25 °C, VCC = +3.4 V, VREF = +2.85 V, 50 Ω system) PARAMETER MIN TYP MAX UNIT COMMENTS 25 24 27.5 26.5 30 28 dB POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V Adjacent Channel Power at 885 kHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -50 -51 -47 -47 dBc POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V Adjacent Channel Power at 1.98 MHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -63 -65 -57 -57 dBc POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V 37 8 40 9 - % POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V Quiescent Current (Icq) - 50 70 mA VMODE = +2.85 V, Low Bias Reference Current - 1.5 3 mA through VREF pin Mode Control Current - 0.3 1.0 mA through VMODE pin Leakage Current - <1 5 A VCC = +4.2 V, VREF = 0 V, VMODE = 0 V Noise in Receive Band - -133 -131 dBm/Hz Harmonics 2fo 3fo, 4fo - -35 -50 -30 -30 dBc Input Impedance - - 2:1 VSWR Gain Power-Added Efficiency (1) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure - - -65 dBc 10:1 - - VSWR Notes: (1) PAE and ACP limit applies at 836.5 MHz. 4 Data Sheet - Rev 2.0 10/2008 869 MHz to 894 MHz POUT < +28 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions Applies over all operating conditions AWT6301R Table 5: Electrical Specifications - CDMA Operation in Low Power Mode (TC = +25 °C, VCC = +3.4 V, VREF = +2.85 V, VMODE = +2.85 V, 50 Ω system) PARAMETER MIN TYP MAX UNIT 24 24 27.0 26.5 29 28 dB POUT = +28 dBm POUT = +16 dBm Adjacent Channel Power at 885 kHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -50 -51 -47 -47 dBc POUT = +28 dBm POUT = +16 dBm Adjacent Channel Power at 1.98 MHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -61 -65 -57 -57 dBc POUT = +28 dBm POUT = +16 dBm 37 8 41 9 - % POUT = +28 dBm POUT = +16 dBm Quiescent Current (Icq) - 50 70 mA VMODE = +2.85 V, Low Bias Reference Current - 1.5 3 mA through VREF pin Mode Control Current - 0.3 1.0 mA through VMODE pin Leakage Current - <1 5 A VCC = +4.2 V, VREF = 0 V, VMODE = 0 V Noise in Receive Band - -133 -131 dBm/Hz Harmonics 2fo 3fo, 4fo - -35 -50 -30 -30 dBc Input Impedance - - 2:1 VSWR Gain Power-Added Efficiency (1) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure - - -65 dBc 10:1 - - VSWR COMMENTS 869 MHz to 894 MHz POUT < +28 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions Applies over all operating conditions Notes: (1) PAE and ACP limit applies at 836.5 MHz. Data Sheet - Rev 2.0 10/2008 5 AWT6301R APPLICATION INFORMATION Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Bias Control table lists the recommended modes of operation for various applications. To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying a logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. Table 8: Bias Control POUT LEVELS BIAS MODE VREF VMODE (all) High +2.85 V 0V CDMA - low power <+28 dBm Low +2.85 V +2.85 V CDMA - high power >+16 dBm High +2.85 V 0V - Shutdown 0V 0V APPLICATION AMPS Shutdown VREF C6 1 µF VMODE RFIN VCC1 C1 10 µF 1 VREF GND 8 2 VMODE RFOUT 7 3 RFIN GND 6 4 VCC1 VCC2 5 C4 68 pF GND at slug Figure 3: Application Circuit 6 Data Sheet - Rev 2.0 10/2008 C5 68 pF RFOUT VCC2 C2 10 µF AWT6301R PACKAGE OUTLINE Figure 4: M9 Package Outline - 8 Pin 3 mm x 3 mm x 1 mm Surface Mount Module 6301R LLLLLNN BBBBCC Figure 5: Branding Specification Data Sheet - Rev 2.0 10/2008 7 AWT6301R COMPONENT PACKAGING Figure 6: Tape & Reel Packaging Table 9: Tape & Reel Dimensions 8 PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 3 mm x 3 mm x 1 mm 12 mm 4 mm 2500 7" Data Sheet - Rev 2.0 10/2008 AWT6301R ORDERING INFORMATION ORDER NUMBER AWT6301RM9Q7 TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING -30 °C to +85 °C 8 Pin 3 mm x 3 mm x 1 mm Surface Mount Module Tape and Reel, 2500 pieces per Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 9 Data Sheet - Rev 2.0 10/2008