Pan Jit GBJ4B Glass passivated single-phase bridge rectifier Datasheet

DATA SHEET
GBJ4A~GBJ4K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
4.0 Amperes
CURRENT
VOLTAGE
50 to 800 Volts
GBJ
Unit: inch (mm)
Recongnized File #E228882
FEATURES
.996(25.3)
C .118(3.0)
.146(3.7)
.129(3.3)
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
.133(3.4)
.603(15.3)
.578(14.7)
• Reliable low cost construction utilizing molded plastic technique
.150(3.8)
.382(9.7)
.366(9.3)
• Ideal for printed circuit board
.189(4.8)
.173(4.4)
.972(24.7)
.142(3.6)
.122(3.1)
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
• Pb free product are available : 99% Sn above can meet Rohs environment
.709(18.0)
.669(17.0)
substance directive request
.087(2.2)
.070(1.8)
.044(1.1)
.035(0.9)
MECHANICALDATA
.115(2.9)
.098(2.5)
Case: Reliable low cost construction utilizing
.304(7.7)
.288(7.3)
molded plastic technique
.304(7.7)
.288(7.3)
.304(7.7)
.288(7.3)
Terminals: Leads solderable per MIL-STD-202G,
.032(0.8)
.024(0.6)
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
PA RA M E TE R
S YM B O L
GB J 4 A
M a xi m um R e c ur r e nt P e a k R e ve r s e V o l t a g e
V RRM
50
100
200
400
600
800
V
M a x i m u m R M S B r i d g e In p u t V o l t a g e
V RM S
35
70
140
280
420
560
V
V DC
50
100
200
400
600
800
V
M a xi m um D C B l o c k i ng V o l t a g e
G B J 4 B G B J 4 D G B J 4 G G B J 4 J G B J 4 K U N IT S
M a xi m um A ve r a g e F o r w a r d R e c t i f i e d O ut p ut C ur r e nt a t
TC = 1 0 0 OC
I AV
4 .0
A
I2 t R a t i n g f o r f u s i n g ( t < 8 . 3 m s )
I2 t
93
A 2s e c
P e a k F o r w a r d S ur g e C ur r e nt s i ng l e s i ne - w a ve s up e r i m p o s e d
o n r a t e d l o a d ( J E D E C m e t ho d )
IF S M
150
Apk
M a x i m u m In s t a n t a n e o u s F o r w a r d V o l t a g e D r o p p e r e l e m e n t a t
2 .0 A
VF
1 .0
Vpk
M a xi m um R e ve r s e L e a k a g e C ur r e nt a t R a t e d @ T A = 2 5 OC
D c B l o c k i ng V o l t a g e @ T A = 1 0 0 OC
IR
5 .0
500
uA
Rθ J A
Rθ J C
8 .6
3 .1
T J ,T S TG
-5 5 to + 1 5 0
Ty p i c a l T h e r m a l R e s i s t a n c e p e r l e g ( N o t e 2 )
(No te 3 )
O p e r a t i n g J u n c t i o n a n d S t o r a g e Te m p e r a t u r e R a n g e
O
C /W
O
C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
STAD-FEB.20.2004
PAGE . 1
HEAT-SINK
MOUNTING, T C
(4 x 4 x 0.15cm)THK
COPPER PLATE
4.0
2.0
MOUNTED ON PC BOARD,
TA 0.5 (12.7mm)LEAD LENGTH
60Hz RESISTIVE OR INDUCTIVE LOAD
0
0
50
100
150
O
TEMPERATURE, C
REVERSE CURRENT,uA
4
10
3
O
T J =150 C
10 2
10 1
10
0
O
T J =25 C
10
10
-1
-2
0
10
20
30
40
50
60
70
80
90
100 110
PERCENT OF PEAK REVERE VOLTAGE,%
Fig.3 - TYPICAL REVERSE CHARACTERISTICS
STAD-FEB.20.2004
150
120
90
60
30
0
1
6
2
10
20
40
60
100
NO. OF CYCLES AT 60Hz
Fig.1 - DERATING CURVE FOR OUTPUT
RECTIFIED CURRENT
10
FORWARD SURGE CURRENT, AMPERES pk
(HALF SINE-WAVE)
6.0
Fig.2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
INSTANTANEOUS FORWARD CURRENT, AMPERES
AVERAGE FORWARD CURRENT
AMPERES
RATING AND CHARACTERISTIC CURVES
100
40
20
10
4.0
2.0
1.0
O
0.4
TJ=25 C
Pulse Width = 300us
1% DULY Cycle
0.2
0.1
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
Fig.4 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER ELEMENT
PAGE . 2
Similar pages