LM2907EP,LM2917EP LM2907EP / LM2917EP Enhanced Plastic Frequency to Voltage Converter Literature Number: SNOSAB0A LM2907EP/LM2917EP Enhanced Plastic Frequency to Voltage Converter General Description Features The LM2907EP, LP2917EP series are monolithic frequency to voltage converters with a high gain op amp/comparator designed to operate a relay, lamp, or other load when the input frequency reaches or exceeds a selected rate. The tachometer uses a charge pump technique and offers frequency doubling for low ripple, full input protection in two versions (LM2907-8EP, LM2917-8EP) and its output swings to ground for a zero frequency input. The op amp/comparator is fully compatible with the tachometer and has a floating transistor as its output. This feature allows either a ground or supply referred load of up to 50 mA. The collector may be taken above VCC up to a maximum VCE of 28V. The two basic configurations offered include an 8-pin device with a ground referenced tachometer input and an internal connection between the tachometer output and the op amp non-inverting input. This version is well suited for single speed or frequency switching or fully buffered frequency to voltage conversion applications. The more versatile configurations provide differential tachometer input and uncommitted op amp inputs. With this version the tachometer input may be floated and the op amp becomes suitable for active filter conditioning of the tachometer output. Both of these configurations are available with an active shunt regulator connected across the power leads. The regulator clamps the supply such that stable frequency to voltage and frequency to current operations are possible with any supply voltage and a suitable resistor. ENHANCED PLASTIC • Extended Temperature Performance of −40°C to +85°C • Baseline Control - Single Fab & Assembly Site • Process Change Notification (PCN) • Qualification & Reliability Data • Solder (PbSn) Lead Finish is standard • Enhanced Diminishing Manufacturing Sources (DMS) Support ■ Ground referenced tachometer input interfaces directly ■ ■ ■ ■ ■ ■ ■ with variable reluctance magnetic pickups Op amp/comparator has floating transistor output 50 mA sink or source to operate relays, solenoids, meters, or LEDs Frequency doubling for low ripple Tachometer has built-in hysteresis with either differential input or ground referenced input Built-in zener on LM2917EP ±0.3% linearity typical Ground referenced tachometer is fully protected from damage due to swings above VCC and below ground Advantages ■ ■ ■ ■ Output swings to ground for zero frequency input Easy to use; VOUT = fIN × VCC × R1 × C1 Only one RC network provides frequency doubling Zener regulator on chip allows accurate and stable frequency to voltage or current conversion (LM2917EP) Applications ■ Selected Military Applications ■ Selected Avionics Applications Ordering Information Part Number VIN Part Number NS Package Number (Note 3) LM2907MX-8EP V62/04635-01 M08A LM2917MXEP V62/04635-02 M14A (Note 1, Note 2) TBD TBD Note 1: For the following (Enhanced Plastic) versions, check for availablility: LM2907M-8EP, LM2907MEP, LM2907MXEP, LM2907N-8EP, LM2907NEP and LM2917M-8EP, LM2917MX-8EP, LM2917MEP, LM2917N-8EP, LM2917NEP. Parts listed with an "X" are provided in Tape & Reel and parts without an "X" are in Rails. Note 2: FOR ADDITIONAL ORDERING AND PRODUCT INFORMATION, PLEASE VISIT THE ENHANCED PLASTIC WEB SITE AT: www.national.com/ mil Note 3: Refer to package details under Physical Dimensions © 2011 National Semiconductor Corporation 200906 200906 Version 2 Revision 5 www.national.com Print Date/Time: 2011/09/23 13:48:46 LM2907EP/LM2917EP Enhanced Plastic Frequency to Voltage Converter OBSOLETE September 23, 2011 LM2907EP/LM2917EP Enhanced Plastic Block and Connection Diagrams Dual-In-Line and Small Outline Packages, Top Views 20090601 20090602 LM2907-8 See NS Package Number M08A or N08E LM2917-8 See NS Package Number M08A or N08E 20090603 20090604 LM2907 See NS Package Number M14A or N14A www.national.com LM2917 See NS Package Number M14A or N14A 2 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Collector Voltage Differential Input Voltage Tachometer Op Amp/Comparator Input Voltage Range Tachometer LM2907-8EP, LM2917-8EP LM2907EP, LM2917EP 28V 28V 28V 28V ±28V 0.0V to +28V Electrical Characteristics Symbol 0.0V to +28V 1200 mW 1580 mW −40°C to +85°C −65°C to +150°C 260°C 215°C 220°C VCC = 12 VDC, TA = 25°C, see test circuit Parameter Conditions Min Typ Max Units ±10 ±25 ±40 mV TACHOMETER Input Thresholds VIN = 250 mVp-p @ 1 kHz (Note 5) Hysteresis VIN = 250 mVp-p @ 1 kHz (Note 5) Offset Voltage VIN = 250 mVp-p @ 1 kHz (Note 5) 30 LM2907EP/LM2917EP LM2907-8EP/LM2917-8EP mV 3.5 5 10 15 mV mV 1 μA Input Bias Current VIN = ±50 mVDC 0.1 VOH Pin 2 VIN = +125 mVDC (Note 6) 8.3 VOL Pin 2 VIN = −125 mVDC (Note 6) I2, I3 Output Current V2 = V3 = 6.0V (Note 7) I3 Leakage Current I2 = 0, V3 = 0 K Gain Constant (Note 6) 0.9 1.0 1.1 Linearity fIN = 1 kHz, 5 kHz, 10 kHz (Note 8) −1.0 0.3 +1.0 % 3 10 mV 500 nA VCC−1.5V V V 2.3 140 180 V 240 μA 0.1 μA OP/AMP COMPARATOR VOS VIN = 6.0V IBIAS VIN = 6.0V 50 Input Common-Mode Voltage 0 Voltage Gain 40 200 V/mV 50 mA Output Sink Current VC = 1.0 Output Source Current VE = VCC −2.0 10 Saturation Voltage ISINK = 5 mA 0.1 ISINK = 20 mA ISINK = 50 mA 1.0 RDROP = 470Ω 7.56 mA 0.5 V 1.0 V 1.5 V ZENER REGULATOR Regulator Voltage Series Resistance 10.5 Temperature Stability +1 Total Supply Current 3.8 V 15 Ω mV/°C 6 mA Note 4: For operation in ambient temperatures above 25°C, the device must be derated based on a 150°C maximum junction temperature and a thermal resistance of 101°C/W junction to ambient for LM2907-8EP and LM2917-8EP, and 79°C/W junction to ambient for LM2907-14EP and LM2917-14EP. Note 5: Hysteresis is the sum +VTH − (−VTH), offset voltage is their difference. See test circuit. Note 6: VOH is equal to ¾ × VCC − 1 VBE, VOL is equal to ¼ × VCC − 1 VBE therefore VOH − VOL = VCC/2. The difference, VOH − VOL, and the mirror gain, I2/I3, are the two factors that cause the tachometer gain constant to vary from 1.0. Note 7: Be sure when choosing the time constant R1 × C1 that R1 is such that the maximum anticipated output voltage at pin 3 can be reached with I3 × R1. The maximum value for R1 is limited by the output resistance of pin 3 which is greater than 10 MΩ typically. Note 8: Nonlinearity is defined as the deviation of VOUT (@ pin 3) for fIN = 5 kHz from a straight line defined by the VOUT @ 1 kHz and VOUT @ 10 kHz. C1 = 1000 pF, R1 = 68k and C2 = 0.22 mFd. 3 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 www.national.com LM2907EP/LM2917EP Enhanced Plastic Op Amp/Comparator Power Dissipation (Note 4) LM2907-8EP, LM2917-8EP LM2907-14EP, LM2917-14EP Operating Temperature Range Storage Temperature Range Soldering Information Dual-In-Line Package Soldering (10 seconds) Small Outline Package Vapor Phase (60 seconds) Infrared (15 seconds) Absolute Maximum Ratings (Note 4) LM2907EP/LM2917EP Enhanced Plastic Test Circuit and Waveform 20090606 Tachometer Input Threshold Measurement 20090607 www.national.com 4 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 LM2907EP/LM2917EP Enhanced Plastic Typical Performance Characteristics Total Supply Current Zener Voltage vs Temperature 20090640 20090641 Normalized Tachometer Output vs Temperature Normalized Tachometer Output vs Temperature 20090643 20090642 Tachometer Currents I2 and I3 vs Supply Voltage Tachometer Currents I2 and I3 vs Temperature 20090644 20090645 5 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 www.national.com LM2907EP/LM2917EP Enhanced Plastic Tachometer Linearity vs Temperature Tachometer Linearity vs Temperature 20090647 20090646 Tachometer Linearity vs R1 Tachometer Input Hysteresis vs Temperature 20090648 20090649 Op Amp Output Transistor Characteristics Op Amp Output Transistor Characteristics 20090651 20090650 www.national.com 6 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 The LM2907EP series of tachometer circuits is designed for minimum external part count applications and maximum versatility. In order to fully exploit its features and advantages let's examine its theory of operation. The first stage of operation is a differential amplifier driving a positive feedback flipflop circuit. The input threshold voltage is the amount of differential input voltage at which the output of this stage changes state. Two options (LM2907-8EP, LM2917-8EP) have one input internally grounded so that an input signal must swing above and below ground and exceed the input thresholds to produce an output. This is offered specifically for magnetic variable reluctance pickups which typically provide a single-ended ac output. This single input is also fully protected against voltage swings to ±28V, which are easily attained with these types of pickups. The differential input options (LM2907EP, LM2917EP) give the user the option of setting his own input switching level and still have the hysteresis around that level for excellent noise rejection in any application. Of course in order to allow the inputs to attain common-mode voltages above ground, input protection is removed and neither input should be taken outside the limits of the supply voltage being used. It is very important that an input not go below ground without some resistance in its lead to limit the current that will then flow in the epi-substrate diode. Following the input stage is the charge pump where the input frequency is converted to a dc voltage. To do this requires one timing capacitor, one output resistor, and an integrating or filter capacitor. When the input stage changes state (due to a suitable zero crossing or differential voltage on the input) the timing capacitor is either charged or discharged linearly between two voltages whose difference is VCC/2. Then in one half cycle of the input frequency or a time equal to 1/2 fIN the change in charge on the timing capacitor is equal to VCC/2 × C1. The average amount of current pumped into or out of the capacitor then is: CHOOSING R1 AND C1 There are some limitations on the choice of R1 and C1 which should be considered for optimum performance. The timing capacitor also provides internal compensation for the charge pump and should be kept larger than 500 pF for very accurate operation. Smaller values can cause an error current on R1, especially at low temperatures. Several considerations must be met when choosing R1. The output current at pin 3 is internally fixed and therefore VO/R1 must be less than or equal to this value. If R1 is too large, it can become a significant fraction of the output impedance at pin 3 which degrades linearity. Also output ripple voltage must be considered and the size of C2 is affected by R1. An expression that describes the ripple content on pin 3 for a single R1C2 combination is: It appears R1 can be chosen independent of ripple, however response time, or the time it takes VOUT to stabilize at a new voltage increases as the size of C2 increases, so a compromise between ripple, response time, and linearity must be chosen carefully. As a final consideration, the maximum attainable input frequency is determined by VCC, C1 and I2: USING ZENER REGULATED OPTIONS (LM2917EP) For those applications where an output voltage or current must be obtained independent of supply voltage variations, the LM2917EP is offered. The most important consideration in choosing a dropping resistor from the unregulated supply to the device is that the tachometer and op amp circuitry alone require about 3 mA at the voltage level provided by the zener. At low supply voltages there must be some current flowing in the resistor above the 3 mA circuit current to operate the regulator. As an example, if the raw supply varies from 9V to 16V, a resistance of 470Ω will minimize the zener voltage variation to 160 mV. If the resistance goes under 400Ω or over 600Ω the zener variation quickly rises above 200 mV for the same input variation. The output circuit mirrors this current very accurately into the load resistor R1, connected to ground, such that if the pulses of current are integrated with a filter capacitor, then VO = ic × R1, and the total conversion equation becomes: VO = VCC × fIN × C1 × R1 × K Where K is the gain constant—typically 1.0. 7 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 www.national.com LM2907EP/LM2917EP Enhanced Plastic The size of C2 is dependent only on the amount of ripple voltage allowable and the required response time. Applications Information LM2907EP/LM2917EP Enhanced Plastic Typical Applications Minimum Component Tachometer 20090608 20090609 www.national.com 8 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 LM2907EP/LM2917EP Enhanced Plastic Zener Regulated Frequency to Voltage Converter 20090610 Breaker Point Dwell Meter 20090611 9 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 www.national.com LM2907EP/LM2917EP Enhanced Plastic Voltage Driven Meter Indicating Engine RPM VO = 6V @ 400 Hz or 6000 ERPM (8 Cylinder Engine) 20090612 Current Driven Meter Indicating Engine RPM IO = 10 mA @ 300 Hz or 6000 ERPM (6 Cylinder Engine) 20090613 www.national.com 10 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 LM2907EP/LM2917EP Enhanced Plastic Capacitance Meter VOUT = 1V–10V for CX = 0.01 to 0.1 mFd (R = 111k) 20090614 Two-Wire Remote Speed Switch 20090615 11 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 www.national.com LM2907EP/LM2917EP Enhanced Plastic 100 Cycle Delay Switch 20090616 Variable Reluctance Magnetic Pickup Buffer Circuits 20090617 20090639 Precision two-shot output frequency equals twice input frequency. Pulse height = VZENER www.national.com 12 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 20090619 20090618 Flashing LED Indicates Overspeed 20090620 Flashing begins when fIN ≥ 100 Hz. Flash rate increases with input frequency increase beyond trip point. 13 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 www.national.com LM2907EP/LM2917EP Enhanced Plastic Finger Touch or Contact Switch LM2907EP/LM2917EP Enhanced Plastic Frequency to Voltage Converter with 2 Pole Butterworth Filter to Reduce Ripple 20090621 www.national.com 14 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 20090623 20090622 Some Frequency Switch Applications May Require Hysteresis in the Comparator Function Which can be Implemented in Several Ways: 20090624 15 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 www.national.com LM2907EP/LM2917EP Enhanced Plastic Overspeed Latch LM2907EP/LM2917EP Enhanced Plastic 20090625 20090626 20090628 20090627 www.national.com 16 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 20090630 20090629 Changing Tachometer Gain Curve or Clamping the Minimum Output Voltage 20090632 20090631 17 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 www.national.com LM2907EP/LM2917EP Enhanced Plastic Changing the Output Voltage for an Input Frequency of Zero LM2907EP/LM2917EP Enhanced Plastic Anti-Skid Circuit Functions “Select-Low” Circuit 20090633 20090634 VOUT is proportional to the lower of the two input wheel speeds. www.national.com 18 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 LM2907EP/LM2917EP Enhanced Plastic “Select-High” Circuit 20090635 20090636 VOUT is proportional to the higher of the two input wheel speeds. “Select-Average” Circuit 20090637 19 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 www.national.com LM2907EP/LM2917EP Enhanced Plastic Equivalent Schematic Diagram 20090638 *This connection made on LM2907-8EP and LM2917-8EP only. **This connection made on LM2917EP and LM2917-8EP only. www.national.com 20 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 LM2907EP/LM2917EP Enhanced Plastic Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead (0.150″ Wide) Molded Small Outline Package, JEDEC NS Package Number M08A 14-Lead Molded SO Package NS Package Number M14A 21 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 www.national.com LM2907EP/LM2917EP Enhanced Plastic Molded Dual-In-Line Package (N) NS Package Number N08E Molded Dual-In-Line Package (N) NS Package Number N14A www.national.com 22 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 LM2907EP/LM2917EP Enhanced Plastic Notes 23 200906 Version 2 Revision 5 Print Date/Time: 2011/09/23 13:48:46 www.national.com LM2907EP/LM2917EP Enhanced Plastic Frequency to Voltage Converter Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise® Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise® Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] www.national.com Tel: 1-800-272-9959 National Semiconductor Europe Technical Support Center Email: [email protected] 200906 Version 2 Revision 5 National Semiconductor Asia Pacific Technical Support Center Email: [email protected] Print Date/Time: 2011/09/23 13:48:47 National Semiconductor Japan Technical Support Center Email: [email protected] IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated