HT70XXA-1 TinyPowerTM Voltage Detector Features · Low power consumption · Output voltage accuracy: tolerance ± 3% · Low temperature coefficient · Built-in hysteresis characteristic · High input voltage range (up to 24V) · TO-92, SOT-89 and SOT-25 package Applications · Battery checkers · Microcomputer reset · Level selectors · Battery memory backup · Power failure detectors · Non-volatile RAM signal storage protectors General Description comparator, hysteresis circuit, and an output driver. CMOS technology ensures low power consumption. The HT70XXA-1 series devices area set of three terminal low power voltage detectors implemented in CMOS technology. Each voltage detector in the series detects a particular fixed voltage ranging from 2.2V to 5V. The voltage detectors consist of a high-precision and low power consumption standard voltage source as well as a Although designed primarily as fixed voltage detectors, these devices can be used with external components to detect user specified threshold voltages. Selection Table Detectable Voltage Hysteresis Width Tolerance HT7022A-1 2.2V 0.11V ±3% HT7024A-1 2.4V 0.12V ±3% HT7027A-1 2.7V 0.135V ±3% HT7033A-1 3.3V 0.165V ±3% HT7039A-1 3.9V 0.195V ±3% HT7044A-1 4.4V 0.22V ±3% HT7050A-1 5.0V 0.25V ±3% Part No. Note: Package TO-92 SOT-89 SOT-25 Marking 70XXA-1 (for TO-92) 70XXA-1 (for SOT-89) 0XXA (for SOT-25) ²XX² stands for output voltages. For lead free devices, TO-92 package will add a ²#² mark at the end of the date code, whereas SOT-89 & SOT-25 packages will add a ²#² mark at the end of the marking. Rev. 1.40 1 January 26, 2006 HT70XXA-1 Block Diagram N Channel Open Drain Output (Normal Open; Active Low) V O U T V D D V R E F G N D Output Table & Curve V VDD VDD>VDET(+) VDD£VDET(-) VOUT Hi-Z VSS O U T D a s h lin e ... V S o lid lin e ... V V V D E T V D E T V ´ 1 .0 5 IN IN fro m L fro m H O I ® ® L H I O IN H Y S Pin Assignment T O -9 2 S O T -8 9 S O T -2 5 N C N C F r o n t V ie w 7 0 X X A -1 7 0 X X A -1 T o p V ie w 0 X X A O U T O U T V D D V S S V S S B o tto m O U T V D D V S S O U T V D D V S S V ie w O U T Rev. 1.40 V D D V D D V S S 2 January 26, 2006 HT70XXA-1 Absolute Maximum Ratings Supply Voltage .............................................................................................................................VSS-0.3V to VSS+26V Output Voltage ...........................VSS-0.3V to VDD+0.3V Output Current......................................................50mA Storage Temperature ............................-50°C to 125°C Power Consumption ..........................................200mW Operating Temperature ...........................-40°C to 85°C Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. Electrical Characteristics HT7022A-1 Symbol VDET Ta=25°C Parameter Detection Voltage Test Conditions Min. Typ. Max. Unit ¾ 2.134 2.200 2.266 V ¾ 0.02 VDET 0.05 VDET 0.1 VDET V ¾ 4 7 mA 1.5 ¾ 24 V VDD Conditions ¾ VHYS Hysteresis Width ¾ IDD Operating Current 8V VDD Operating Voltage ¾ IOL Output Sink Current 2V VOUT=0.2V 0.5 1 ¾ mA DVDET DTa Temperature Coefficient ¾ 0°C<Ta<70°C ¾ ±1.1 ¾ mV/°C No load ¾ HT7024A-1 Symbol Ta=25°C Parameter Test Conditions VDD Conditions Min. Typ. Max. Unit VDET Detection Voltage ¾ ¾ 2.328 2.400 2.472 V VHYS Hysteresis Width ¾ ¾ 0.02 VDET 0.05 VDET 0.1 VDET V IDD Operating Current 8V ¾ 4 7 mA VDD Operating Voltage ¾ 1.5 ¾ 24 V IOL Output Sink Current 2V VOUT=0.2V 0.5 1 ¾ mA DVDET DTa Temperature Coefficient ¾ 0°C<Ta<70°C ¾ ±0.9 ¾ mV/°C Rev. 1.40 No load ¾ 3 January 26, 2006 HT70XXA-1 HT7027A-1 Symbol Ta=25°C Parameter Test Conditions VDD Conditions Min. Typ. Max. Unit VDET Detection Voltage ¾ ¾ 2.619 2.700 2.781 V VHYS Hysteresis Width ¾ ¾ 0.02 VDET 0.05 VDET 0.1 VDET V IDD Operating Current 8V ¾ 4 7 mA VDD Operating Voltage ¾ 1.5 ¾ 24 V IOL Output Sink Current 2V VOUT=0.2V 0.5 1 ¾ mA DVDET DTa Temperature Coefficient ¾ 0°C<Ta<70°C ¾ ±0.9 ¾ mV/°C No load ¾ HT7033A-1 Symbol Ta=25°C Parameter Test Conditions VDD Conditions Min. Typ. Max. Unit VDET Detection Voltage ¾ ¾ 3.201 3.300 3.399 V VHYS Hysteresis Width ¾ ¾ 0.02 VDET 0.05 VDET 0.1 VDET V IDD Operating Current 8V ¾ 4 7 mA VDD Operating Voltage ¾ 1.5 ¾ 24 V IOL Output Sink Current VOUT=0.25V 1.2 2.5 ¾ mA DVDET DTa Temperature Coefficient 0°C<Ta<70°C ¾ ±0.9 ¾ mV/°C No load ¾ 2.5V ¾ HT7039A-1 Symbol Ta=25°C Parameter Test Conditions VDD Conditions Min. Typ. Max. Unit VDET Detection Voltage ¾ ¾ 3.783 3.900 4.017 V VHYS Hysteresis Width ¾ ¾ 0.02 VDET 0.05 VDET 0.1 VDET V IDD Operating Current 8V ¾ 4 7 mA VDD Operating Voltage ¾ IOL Output Sink Current DVDET DTa Temperature Coefficient Rev. 1.40 2.5V ¾ No load 1.5 ¾ 24 V VOUT=0.25V ¾ 1.2 2.5 ¾ mA 0°C<Ta<70°C ¾ ±0.9 ¾ mV/°C 4 January 26, 2006 HT70XXA-1 HT7044A-1 Ta=25°C Symbol Parameter Test Conditions VDD Conditions Min. Typ. Max. Unit VDET Detection Voltage ¾ ¾ 4.268 4.400 4.532 V VHYS Hysteresis Width ¾ ¾ 0.02 VDET 0.05 VDET 0.1 VDET V IDD Operating Current 8V ¾ 4 7 mA VDD Operating Voltage ¾ 1.5 ¾ 24 V IOL Output Sink Current VOUT=0.36V 3 6 ¾ mA DVDET DTa Temperature Coefficient 0°C<Ta<70°C ¾ ±0.9 ¾ mV/°C No load ¾ 3.6V ¾ HT7050A-1 Ta=25°C Symbol VDET Parameter Detection Voltage Test Conditions Min. Typ. Max. Unit ¾ 4.850 5.000 5.150 V ¾ 0.02 VDET 0.05 VDET 0.1 VDET V ¾ 4 7 mA VDD Conditions ¾ VHYS Hysteresis Width ¾ IDD Operating Current 8V VDD Operating Voltage IOL Output Sink Current DVDET DTa Temperature Coefficient No load ¾ 3.6V ¾ 2.1 ¾ 24 V VOUT=0.36V ¾ 3 6 ¾ mA 0°C<Ta<70°C ¾ ±0.9 ¾ mV/°C Functional Description The HT70XXA-1 series is a set of voltage detectors equipped with a high stability voltage reference which is connected to the negative input of a comparator¾ denoted as VREF in the following figure for NMOS output voltage detector. The hysteresis width is: VHYS = VDET (+) - VDET (-) The figure demonstrates the NMOS output type with positive output polarity (VOUT is normally open, active low). The HT70XXA-1 series also supplies options for other output types with active high outputs. Application circuits shown are examples of positive output polarity (normally open, active low) unless otherwise specified. When the voltage drop to the positive input of the comparator (i,e,VB) is higher than VREF, VOUT goes high, M1 turns off, and VB is expressed as VBH=VDD ´ (RB+RC) / (RA+RB+RC). If VDD is decreased so that VB falls to a value less than VREF, the comparator output inverts from high to low, VOUT goes low, VC is high, M1 turns on, RC is bypassed, and VB becomes: VBL= VDD ´ RB / (RA+RB), which is less than VBH. By so doing, the comparator output will stay low to prevent the circuit from oscillating when VB » VREF. V R V V R E F R R L V B C V O U T M N B M 1 The detectable voltage is defined as: R RA + RB + RC ´ VREF RB + RC C V The release voltage is defined as: RA + RB ´ VREF VDET (+) = RB Rev. 1.40 A C o m p a ra to r If VDD falls below the minimum operating voltage, the output becomes undefined. When VDD goes from low to VDD ´ RB / (RA+RB) > VREF, the comparator output and VOUT goes high. VDET (-) = D D S S NMOS Output Voltage Detector (HT70XXA-1) 5 January 26, 2006 HT70XXA-1 Application Circuits Microcomputer Reset Circuit Power-on Reset Circuit Normally a reset circuit is required to protect the microcomputer system from malfunctions due to power line interruptions. The following examples show how different output configurations perform a reset function in various systems. With several external components, the NMOS open drain type of the HT70XXA-1 series can be used to perform a power-on reset function as shown: V IN R · NMOS open drain output application for separate D power supply V V D D 1 V H T 7 0 X X A -1 V D D 2 D D V C O U T R E S E T M ic r o C o m p u te r O U T V O U T V S S H T 7 0 X X A -1 V S S V V D D S S · NMOS open drain output application with R-C delay V D D R H T 7 0 X X A -1 V O U T t M ic r o C o m p u te r V O U T C V S S t 5V Power Line Monitoring Circuit Generally, a minimum operating voltage of 4.5V is guaranteed in a 5V power line system. The HT7044A-1 is recommended for use as 5V power line monitoring circuit. · 5V power line monitor with power-on reset 5 V P o w e r lin e R D V D D C V O U T H T 7 0 4 4 A -1 V Rev. 1.40 6 S S V S S January 26, 2006 HT70XXA-1 · with 5V voltage regulator Malfunction Analysis The following circuit demonstrates the way a circuit analyzes malfunctions by monitoring the variation or spike noise of power supply voltage. 5 V V o lta g e r e g u la to r V 5 V H T 7 1 5 0 -1 IN V D D V S S G N D V D D V V H T 7 0 X X A -1 H T 7 0 4 4 A -1 V V S S S S Charge Monitoring Circuit Change of Detectable Voltage The following circuit shows a charged monitor for p r o t e ct i o n a g a i n st b a t t e r y d e t e r i o r a t i o n b y overcharging. When the voltage of the battery is higher than the set detectable voltage, the transistor turns on to bypass the charge current, protecting the battery from overcharging. If the required voltage is not found in the standard product selection table, it is possible to change it by using external resistance dividers or diodes. · Varying the detectable voltage with a resistance di- vider V O U T O U T IN R V R V V A D D V O U T V S S S o la r C e ll V O U T D D B A T T T r L o a d H T 7 0 X X A -1 B S S V S S H T 7 0 X X A -1 RA + RB ´ VDET RB RA + RB Hysteresis width = ´ VHYS RB Detectable voltage = · Varying the detectable voltage with a diode V IN V f1 V f2 V D D V O U T H T 7 0 X X A -1 V V S S S S Detectable Voltage = Vf1+Vf2+VDET Rev. 1.40 7 January 26, 2006 HT70XXA-1 Level Selector The following diagram illustrates a logic level selector. V D D V V S S V 5 .0 V V D E T 1 3 .9 V V D E T 2 V O U T H T 7 0 3 9 A -1 H T 7 0 5 0 A -1 V V D E T 2 V O U T O U T D E T 1 D D t V O U T t Rev. 1.40 8 January 26, 2006 HT70XXA-1 Package Information 3-Pin TO-92 Outline Dimensions A B D C E F G H Symbol A Rev. 1.40 Dimensions in mil Min. Nom. Max. 170 ¾ 200 B 170 ¾ 200 C 500 ¾ ¾ D 11 ¾ 20 E 90 ¾ 110 F 45 ¾ 55 G 45 ¾ 65 H 130 ¾ 160 I 8 ¾ 18 a 4° ¾ 6° 9 January 26, 2006 HT70XXA-1 3-Pin SOT-89 Outline Dimensions I A J B C E D G F Symbol Rev. 1.40 H Dimensions in mil Min. Nom. Max. A 173 ¾ 181 B 64 ¾ 72 C 90 ¾ 102 D 35 ¾ 47 E 155 ¾ 167 F 14 ¾ 19 G 17 ¾ 22 H ¾ 59 ¾ I 55 ¾ 63 J 14 ¾ 17 10 January 26, 2006 HT70XXA-1 5-Pin SOT-25 Outline Dimensions D C L H E q e A A 2 b Symbol Rev. 1.40 A 1 Dimensions in mm Min. Nom. Max. A 1.00 ¾ 1.30 A1 ¾ ¾ 0.10 A2 0.70 ¾ 0.90 b 0.35 ¾ 0.50 C 0.10 ¾ 0.25 D 2.70 ¾ 3.10 E 1.40 ¾ 1.80 e ¾ 1.90 ¾ H 2.60 ¾ 3 L 0.37 ¾ ¾ q 1° ¾ 9° 11 January 26, 2006 HT70XXA-1 Product Tape and Reel Specifications TO-92 Reel Dimensions (Unit: mm) P a c k a g e U p , F la t S id e U p 3 0 P a c k a g e U p , F la t S id e D o w n 4 3 5 8 8 8 3 6 0 Rev. 1.40 12 January 26, 2006 HT70XXA-1 Reel Dimensions D T 2 A C B T 1 SOT-89 Symbol Description Dimensions in mm A Reel Outer Diameter 180±1.0 B Reel Inner Diameter 62±1.5 C Spindle Hole Diameter D Key Slit Width 1.9±0.15 T1 Space Between Flange 12.4+0.2 T2 Reel Thickness 12.75+0.15 17-0.4 SOT-25 Symbol Description Dimensions in mm A Reel Outer Diameter 178±1.0 B Reel Inner Diameter 62±1.0 C Spindle Hole Diameter 13.0±0.2 D Key Slit Width 2.5±0.25 T1 Space Between Flange 8.4+1.5 -0.0 T2 Reel Thickness 11.4+1.5 Rev. 1.40 13 January 26, 2006 HT70XXA-1 TO-92 Carrier Tape Dimensions P D h W 2 H 1 H H 0 l1 W 0 t W 1 W F 1 F 2 D 0 P 2 P 0 TO-92 Symbol Note: Description Dimensions in mm I1 Taped Lead Length (2.5) P Component Pitch 12.7±1.0 P0 Perforation Pitch 12.7±0.3 P2 Component to Perforation (Length Direction) 6.35±0.4 F1 Lead Spread 2.5+0.4 -0.1 F2 Lead Spread 2.5+0.4 -0.1 Dh Component Alignment 0±0.1 W Carrier Tape Width 18.0+1.0 -0.5 W0 Hold-down Tape Width 6.0±0.5 W1 Perforation Position 9.0±0.5 W2 Hold-down Tape Position H0 Lead Clinch Height 16.0±0.5 H1 Component Height Less than 24.7 D0 Perforation Diameter 4.0±0.2 t Taped Lead Thickness 0.7±0.2 H Component Base Height 19.0±0.5 (0.5) Thickness less than 0.38±0.05mm~0.5mm P0 Accumulated pitch tolerance: ±1mm/20pitches. ( ) Bracketed figures are for consultation only Rev. 1.40 14 January 26, 2006 HT70XXA-1 Carrier Tape Dimensions P 0 D P 1 t E F W C D 1 B 0 P K 0 A 0 SOT-89 Symbol Description Dimensions in mm 12.0+0.3 -0.1 W Carrier Tape Width P Cavity Pitch 8.0±0.1 E Perforation Position 1.75±0.1 F Cavity to Perforation (Width Direction) 5.5±0.05 D Perforation Diameter 1.5+0.1 D1 Cavity Hole Diameter 1.5+0.1 P0 Perforation Pitch 4.0±0.1 P1 Cavity to Perforation (Length Direction) 2.0±0.10 A0 Cavity Length 4.8±0.1 B0 Cavity Width 4.5±0.1 K0 Cavity Depth 1.8±0.1 t Carrier Tape Thickness C Cover Tape Width 0.30±0.013 9.3 SOT-25 Symbol Description Dimensions in mm 8.0±0.3 W Carrier Tape Width P Cavity Pitch 4.0 E Perforation Position 1.75 F Cavity to Perforation (Width Direction) 3.5±0.05 D Perforation Diameter 1.5+0.1 D1 Cavity Hole Diameter 1.5+0.1 P0 Perforation Pitch 4.0 P1 Cavity to Perforation (Length Direction) 2.0 A0 Cavity Length 3.15 B0 Cavity Width 3.2 K0 Cavity Depth t Carrier Tape Thickness C Cover Tape Width Rev. 1.40 1.4 0.20±0.03 5.3 15 January 26, 2006 HT70XXA-1 Holtek Semiconductor Inc. (Headquarters) No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan Tel: 886-3-563-1999 Fax: 886-3-563-1189 http://www.holtek.com.tw Holtek Semiconductor Inc. (Taipei Sales Office) 4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan Tel: 886-2-2655-7070 Fax: 886-2-2655-7373 Fax: 886-2-2655-7383 (International sales hotline) Holtek Semiconductor Inc. (Shanghai Sales Office) 7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233 Tel: 021-6485-5560 Fax: 021-6485-0313 http://www.holtek.com.cn Holtek Semiconductor Inc. (Shenzhen Sales Office) 43F, SEG Plaza, Shen Nan Zhong Road, Shenzhen, China 518031 Tel: 0755-8346-5589 Fax: 0755-8346-5590 ISDN: 0755-8346-5591 Holtek Semiconductor Inc. (Beijing Sales Office) Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031 Tel: 010-6641-0030, 6641-7751, 6641-7752 Fax: 010-6641-0125 Holmate Semiconductor, Inc. (North America Sales Office) 46712 Fremont Blvd., Fremont, CA 94538 Tel: 510-252-9880 Fax: 510-252-9885 http://www.holmate.com Copyright Ó 2006 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw. Rev. 1.40 16 January 26, 2006