LP38501-ADJ, LP38503-ADJ www.ti.com SNVS522H – AUGUST 2007 – REVISED APRIL 2013 LP38501/3-ADJ, LP38501A/3A-ADJ 3A FlexCap Low Dropout Linear Regulator for 2.7V to 5.5V Inputs Check for Samples: LP38501-ADJ, LP38503-ADJ FEATURES 1 • 2 • • • • • • • • • • • FlexCap: Stable with Ceramic, Tantalum, or Aluminum Capacitors Stable with 10 µF Input/Output Capacitor Adjustable Output Voltage from 0.6V to 5V Low Ground Pin Current 25 nA Quiescent Current in Shutdown Mode Output Current of 3A Available in TO-263, PFM THIN Packages VADJ Accuracy of ±1.5% at 25°C (A Grade) VADJ Accuracy of ±3.5% at 25°C (STD) Over-Temperature and Over-Current Protection −40°C to +125°C Operating TJ Range Enable Pin (LP38501) APPLICATIONS • • • • ASIC Power Supplies In: – Printers, Graphics Cards, DVD Players – Set Top Boxes, Copiers, Routers DSP and FPGA Power Supplies SMPS Regulator Conversion from 3.3V or 5V Rail DESCRIPTION TI's FlexCap LDO's feature unique compensation that allows the use of any type of output capacitor with no limits on minimum or maximum ESR. The LP38501/3 series of low-dropout linear regulators operates from a +2.7V to +5.5V input supply. These ultra low dropout linear regulators respond very quickly to step changes in load, which makes them suitable for low voltage microprocessor applications. Developed on a CMOS process, (utilizing a PMOS pass transistor), the LP38501/3 has low quiescent current that changes little with load current. Ground Pin Current: Typically 2 mA at 3A load current. Disable Mode: Typically 25 nA quiescent current when the Enable pin is pulled low. Simplified Compensation: Stable with any type of output capacitor, regardless of ESR. Precision Output: "A" grade versions available with 1.5% VADJ tolerance (25°C) and 3% over line, load and temperature. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2007–2013, Texas Instruments Incorporated LP38501-ADJ, LP38503-ADJ SNVS522H – AUGUST 2007 – REVISED APRIL 2013 www.ti.com Typical Application Circuit These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Connection Diagram Top View (LP38501TS-ADJ) Top View (LP38503TS-ADJ) See Package Number KTT0005B (TO-263) See Package Number KTT0005B (TO-263) Connection Diagram Top View (LP38501TJ-ADJ, LP38501ATJ-ADJ) Top View (LP38503TJ-ADJ, LP38503ATJ-ADJ) See Package Number NDQ0005A (PFM THIN) See Package Number NDQ0005A (PFM THIN) Pin Descriptions for TO-263 (TS) and TO-263 THIN (TJ) Pin # Designation EN Enable (LP38501 only). Pull high to enable the output, low to disable the output. This pin has no internal bias and must be either tied to the input voltage, or actively driven. N/C In the LP38503, this pin has no internal connections. It can be left floating or used for trace routing. 1 2 Function Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ LP38501-ADJ, LP38503-ADJ www.ti.com SNVS522H – AUGUST 2007 – REVISED APRIL 2013 Pin Descriptions for TO-263 (TS) and TO-263 THIN (TJ) (continued) Pin # Designation 2 IN Function 3 GND Ground 4 OUT Regulated Output Voltage Pin 5 ADJ Sets output voltage DAP DAP The DAP is used as a thermal connection to remove heat from the device to the circuit board copper clad area which acts as the heatsink. The DAP is electrically connected to the backside of the die. The DAP must be connected to ground potential, but can not be used as the only ground connection. Input Supply Pin ABSOLUTE MAXIMUM RATINGS (1) −65°C to +150°C Storage Temperature Range Lead Temperature (Soldering, 5 sec.) 260°C ESD Rating (2) ±2 kV Power Dissipation (3) Internally Limited Input Pin Voltage (Survival) −0.3V to +6.0V Enable Pin Voltage (Survival) −0.3V to +6.0V −0.3V to +6.0V Output Pin Voltage (Survival) IOUT(Survival) (1) (2) (3) Internally Limited Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but does not specific performance limits. For specifications and conditions, see the Electrical Characteristics. The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin. Operating junction temperature must be evaluated, and derated as needed, based on ambient temperature (TA), power dissipation (PD), maximum allowable operating junction temperature (TJ(MAX)), and package thermal resistance (θJA). See Application Information. OPERATING RATINGS (1) Input Supply Voltage 2.7V to 5.5V Enable Input Voltage 0.0V to 5.5V Output Current (DC) 0 to 3A Junction Temperature (2) −40°C to +125°C VOUT (1) (2) 0.6V to 5V Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but does not specific performance limits. For specifications and conditions, see the Electrical Characteristics. Operating junction temperature must be evaluated, and derated as needed, based on ambient temperature (TA), power dissipation (PD), maximum allowable operating junction temperature (TJ(MAX)), and package thermal resistance (θJA). See Application Information. Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ Submit Documentation Feedback 3 LP38501-ADJ, LP38503-ADJ SNVS522H – AUGUST 2007 – REVISED APRIL 2013 www.ti.com ELECTRICAL CHARACTERISTICS, LP38501/3–ADJ Unless otherwise specified: VIN = 3.3V, IOUT = 10 mA, CIN = 10 µF, COUT = 10 µF, VEN = VIN, VOUT = 1.8V. Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of -40°C to +125°C. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Symbol Parameter Conditions VADJ Adjust Pin Voltage (1) 2.7V ≤ VIN ≤ 5.5V 10 mA ≤ IOUT ≤ 3A VADJ Adjust Pin Voltage (1) "A" GRADE 2.7V ≤ VIN ≤ 5.5V 10 mA ≤ IOUT ≤ 3A IADJ Adjust Pin Bias Current 2.7V ≤ VIN ≤ 5.5V VDO Dropout Voltage (2) Typ Max Units 0.584 0.575 Min 0.605 0.626 0.635 V 0.596 0.587 0.605 0.614 0.623 V 50 750 nA 420 550 665 mV IOUT = 3A 2.7V ≤ VIN ≤ 5.5V — 0.04 0.05 — %/V Output Voltage Load Regulation (4) (1) 10 mA ≤ IOUT ≤ 3A — 0.12 0.24 — %/A Ground Pin Current In Normal Operation Mode 10 mA ≤ IOUT ≤ 3A — 2 4 5 mA IDISABLED Ground Pin Current VEN < VIL(EN) — 0.025 0.125 15 µA IOUT(PK) Peak Output Current VOUT ≥ VOUT(NOM) - 5% 6 A ISC Short Circuit Current VOUT = 0V 3.5 6 A ΔVOUT/ΔVIN Output Voltage Line Regulation (3) ΔVOUT/ΔIOUT IGND (1) Enable Input (LP38501 Only) VIH(EN) Enable Logic High VOUT = ON 1.4 — — VIL(EN) Enable Logic Low VOUT = OFF — — 0.65 td(off) Turn-off delay Time from VEN < VIL(EN) to VOUT = OFF ILOAD = 3A — 25 — td(on) Turn-on delay Time from VEN >VIH(EN) to VOUT = ON ILOAD = 3A — 25 — IIH(EN) Enable Pin High Current VEN = VIN — 35 — IIL(EN) Enable Pin Low Current VEN = 0V — 35 — VIN = 3.0V, IOUT = 3A f = 120Hz — 58 — VIN = 3.0V, IOUT = 3A f = 1 kHz — 56 — Output Noise Density f = 120Hz, COUT = 10 µF CER — 1.0 — µV/√Hz Output Noise Voltage BW = 100Hz – 100kHz COUT = 10 µF CER — 100 — µV (rms) Thermal Shutdown TJ rising — 170 — Thermal Shutdown Hysteresis TJ falling from TSD — 10 — θJ-A Thermal Resistance Junction to Ambient TO-263, PFM THIN (5) 1 sq. in. copper θJ-C Thermal Resistance Junction to Case TO-263, TO-263 THIN V µs nA AC Parameters PSRR ρn(l/f) en Ripple Rejection dB Thermal Characteristics TSD ΔTSD (1) (2) (3) (4) (5) 4 °C 37 °C/W — 5 — The line and load regulation specification contains only the typical number. However, the limits for line and load regulation are included in the output voltage tolerance specification. Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value. For any output voltage less than 2.5V, the minimum VIN operating voltage is the limiting factor. Output voltage line regulation is defined as the change in output voltage from the nominal value due to change in the voltage at the input. Output voltage load regulation is defined as the change in output voltage from the nominal value due to change in the load current at the output. The value of θJA for the TO-263 (TS) package and TO-263 THIN (TJ) package can range from approximately 30 to 60°C/W depending on the amount of PCB copper dedicated to heat transfer (See Application Information). Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ LP38501-ADJ, LP38503-ADJ www.ti.com SNVS522H – AUGUST 2007 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS Unless otherwise specified: TJ = 25°C, VIN = 2.7V, VEN = VIN, CIN = 10 µF, COUT = 10 µF, IOUT = 10 mA, VOUT = 1.8V Noise Density Noise Density Figure 1. Figure 2. IGND vs Load Current IGND(OFF) vs Temperature Figure 3. Figure 4. VADJ vs Temperature Dropout Voltage vs Load Current Figure 5. Figure 6. Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ Submit Documentation Feedback 5 LP38501-ADJ, LP38503-ADJ SNVS522H – AUGUST 2007 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Unless otherwise specified: TJ = 25°C, VIN = 2.7V, VEN = VIN, CIN = 10 µF, COUT = 10 µF, IOUT = 10 mA, VOUT = 1.8V 6 VEN vs Temperature Turn-on Characteristics Figure 7. Figure 8. Load Regulation vs Temperature Turn-on Time Figure 9. Figure 10. Turn-on Time PSRR Figure 11. Figure 12. Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ LP38501-ADJ, LP38503-ADJ www.ti.com SNVS522H – AUGUST 2007 – REVISED APRIL 2013 Block Diagrams Figure 13. LP38501-ADJ Block Diagram Figure 14. LP38503-ADJ Block Diagram APPLICATION INFORMATION EXTERNAL CAPACITORS The LP3850X requires that at least 10 µF (±20%) capacitors be used at the input and output pins located within one cm of the IC. Larger capacitors may be used without limit on size for both CIN and COUT. Capacitor tolerances such as temperature variation and voltage loading effects must be considered when selecting capacitors to ensure that they will provide the minimum required amount of capacitance under all operating conditions for the application. In general, ceramic capacitors are best for noise bypassing and transient response because of their ultra low ESR. It must be noted that if ceramics are used, only the types with X5R or X7R dielectric ratings should be used (never Z5U or Y5F). Capacitors which have the Z5U or Y5F characteristics will see a drop in capacitance of as much as 50% if their temperature increases from 25°C to 85°C. In addition, the capacitance drops significantly with applied voltage: a typical Z5U or Y5F capacitor can lose as much as 60% of it’s rated capacitance if only half of the rated voltage is applied to it. For these reasons, only X5R and X7R ceramics should be used. INPUT CAPACITOR All linear regulators can be affected by the source impedance of the voltage which is connected to the input. If the source impedance is too high, the reactive component of the source may affect the control loop’s phase margin. To ensure proper loop operation, the ESR of the capacitor used for CIN must not exceed 0.5 Ohms. Any good quality ceramic capacitor will meet this requirement, as well as many good quality tantalums. Aluminum electrolytic capacitors may also work, but can possibly have an ESR which increases significantly at cold temperatures. If the ESR of the input capacitor may exceed 0.5 Ohms, it is recommended that a 2.2 µF ceramic capacitor be used in parallel, as this will assure stable loop operation. OUTPUT CAPACITOR Any type of capacitor may be used for COUT, with no limitations on minimum or maximum ESR, as long as the minimum amount of capacitance is present. The amount of capacitance can be increased without limit. Increasing the size of COUT typically will give improved load transient response. Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ Submit Documentation Feedback 7 LP38501-ADJ, LP38503-ADJ SNVS522H – AUGUST 2007 – REVISED APRIL 2013 www.ti.com SETTING THE OUTPUT VOLTAGE The output voltage of the LP38501/3-ADJ can be set to any value between 0.6V and 5V using two external resistors shown as R1 and R2 in Figure 15. Figure 15. The value of R2 should always be less than or equal to 10 kΩ for good loop compensation. R1 can be selected for a given VOUT using the following formula: VOUT = VADJ (1 + R1/R2) + IADJ (R1) where • • VADJ is the adjust pin voltage IADJ is the bias current flowing into the adjust pin (1) STABILITY AND PHASE MARGIN Any regulator which operates using a feedback loop must be compensated in such a way as to ensure adequate phase margin, which is defined as the difference between the phase shift and -180 degrees at the frequency where the loop gain crosses unity (0 dB). For most LDO regulators, the ESR of the output capacitor is required to create a zero to add enough phase lead to ensure stable operation. The LP38501 has a unique internal compensation circuit which maintains phase margin regardless of the ESR of the output capacitor, so any type of capacitor may be used. Figure 16 shows the gain/phase plot of the LP38501-ADJ with an output of 1.2V, 10 µF ceramic output capacitor, delivering 2A of load current. It can be seen that the unity-gain crossover occurs at 300 kHz, and the phase margin is about 40° (which is very stable). Figure 16. Gain-Bandwidth Plot for 2A Load Figure 17 shows the gain and phase with no external load. In this case, the only load is provided by the gain setting resistors (about 12 kΩ total in this test). It is immediately obvious that the unity-gain frequency is significantly lower (dropping to about 500 Hz), at which point the phase margin is 125°. 8 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ LP38501-ADJ, LP38503-ADJ www.ti.com SNVS522H – AUGUST 2007 – REVISED APRIL 2013 Figure 17. Gain-Bandwidth Plot for No Load The reduction in unity-gain bandwidth as load current is reduced is normal for any LDO regulator using a P-FET or PNP pass transistor, because they have a pole in the loop gain function given by: (2) This illustrates how the pole goes to the highest frequency when RL is minimum value (maximum load current). In general, LDO’s have maximum bandwidth (and lowest phase margin) at full load current. In the case of the LP38501, it can be seen that it has good phase margin even when using ceramic capacitors with ESR values of only a few milli Ohms. LOAD TRANSIENT RESPONSE Load transient response is defined as the change in regulated output voltage which occurs as a result of a change in load current. Many applications have loads which vary, and the control loop of the voltage regulator must adjust the current in the pass FET transistor in response to load current changes. For this reason, regulators with wider bandwidths often have better transient response. The LP38501 employs an internal feedforward design which makes the load transient response much faster than would be predicted simply by loop speed: this feedforward means any voltage changes appearing on the output are coupled through to the high-speed driver used to control the gate of the pass FET along a signal path using very fast FET devices. Because of this, the pass transistor’s current can change very quickly. Figure 18 shows the output transient response resulting from a change in load current of 0.1A – 3A, and then 3A – 0.1A with a load current slew rate of 500 mA/µs. As shown in the plots, the resulting change in output voltage is only about 40 mV (peak), which is just slightly over 2% for the 1.8V output used for this test. This is excellent performance for such a small output capacitor. Figure 18. Load Transient Response: 10 µF Ceramic, 0.5A/µs di/dt Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ Submit Documentation Feedback 9 LP38501-ADJ, LP38503-ADJ SNVS522H – AUGUST 2007 – REVISED APRIL 2013 www.ti.com When the load current changes much more quickly, the output voltage will show more change because the loop and internal feedforward circuitry are not able to react as fast as the load changes. In such cases, it is the output capacitor which must supply load current during the transition until the loop responds and changes the pass transistor’s drive to deliver the new value of load current. As an example, the slew rate of the load current will be increased to 75A/µs and the same test will be performed. In Figure 19, it can be seen that the peak excursion of the output voltage during the transient has now increased to about 200 mV, which is just slightly over 11% for the 1.8V output. Figure 19. Load Transient Response: 10 µF Ceramic, 75A/µs di/dt A better understanding of the load transient can be obtained when the load’s rising edge is expanded in time scale (Figure 20). Figure 20. Rising Edge, 10 µF Ceramic, 75A/µs di/dt It can be seen from the figure that the output voltage starts “correcting” back upwards after less than a micro second, and has fully reversed direction after about 1.2 µs. This very rapid reaction is a result of the maximum loop bandwidth (full load is being delivered) and the feedforward effect kicking on the drive to the FET before feedback gets fully around the loop. In cases where extremely fast load changes occur, and output voltage regulation better than 10% is required, the output capacitance must be increased. When selecting capacitors, it must be understood that the better performing ones usually cost the most. For fast changing loads, the internal parasitics of ESR (equivalent series resistance) and ESL (equivalent series inductance) degrade the capacitor’s ability to source current quickly to the load. The best capacitor types for transient performance are (in order): 1. Multilayer Ceramic: with the lowest values of ESR and ESL, they can have ESR values in the range of a few milli Ohms. Disadvantage: capacitance values above about 22 µF significantly increase in cost. 2. Low-ESR Aluminum Electrolytics: these are aluminum types (like OSCON) with a special electrolyte which provides extremely low ESR values, and are the closest to ceramic performance while still providing large amounts of capacitance. These are cheaper (by capacitance) than ceramic. 3. Solid tantalum: can provide several hundred µF of capacitance, transient performance is slightly worse than OSCON type capacitors, cheaper than ceramic in large values. 4. General purpose aluminum electrolytics: cheap and provide a lot of capacitance, but give the worst performance. 10 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ LP38501-ADJ, LP38503-ADJ www.ti.com SNVS522H – AUGUST 2007 – REVISED APRIL 2013 As a first example, larger values of ceramic capacitance will be tried to show how much reduction can be obtained from the 200 mV output change (Figure 20) which was seen with only a 10 µF ceramic output capacitor. In Figure 21, the 10 µF output capacitor is increased to 22 µF. The 200 mV transient is reduced to about 160 mV, which is from about 11% of VOUT down to about 9%. Figure 21. 22 µF Ceramic Output Capacitor In Figure 22, the output capacitance is increased to 47 µF ceramic. It can be seen that the output transient is further reduced down to about 120 mV, which is still about 6.6% of the output voltage. This shows that a 5X increase in ceramic capacitance from the original 10 µF only reduced the peak voltage transient amplitude by about 40%. Figure 22. 47 µF Ceramic Output Capacitor In general, managing load transients is done by paralleling ceramic capacitance with a larger bulk capacitance. In this way, the ceramic can source current during the rapidly changing edge and the bulk capacitor can support the load current after the first initial spike in current. In the next test, the same 10 µF ceramic capacitor will be paralleled with a general purpose (cheap) aluminum electrolytic whose capacitance is 220 µF. As shown in Figure 23, there is a small improvement over the 200 mV peak seen with the 10 µF ceramic alone. By adding the 220 µF aluminum capacitor, the peak is reduced to about 160 mV (the same peak value as seen with a 22 µF ceramic capacitor alone). Figure 23. 10 µF Ceramic Paralleled By 220 µF Generic Aluminum Electrolytic Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ Submit Documentation Feedback 11 LP38501-ADJ, LP38503-ADJ SNVS522H – AUGUST 2007 – REVISED APRIL 2013 www.ti.com A solid Tantalum should work better, so the aluminum electrolytic is replaced by a 220 µF Tantalum (Figure 24). The peak amplitude of the output transient is now reduced to about 130 mV, just slightly worse than the value of the 47 µF ceramic alone. Figure 24. 10 µF Ceramic Paralleled By 220 µF Tantalum The OSCON (ultra low ESR) aluminum electrolytic is the best of the electrolytics. Figure 25 shows the output voltage transient is reduced down to about 90 mV (about 5% of VOUT) when a 220 µF OSCON is added to the 10 µF ceramic. This indicates that some kind of ultra-low ESR aluminum electrolytic used in parallel with some ceramic capacitance is probably the best approach for extremely fast transients, but each application must be dialed in for it’s specific load requirements. Figure 25. 10 µF Ceramic Paralleled By 220 µF OSCON PRINTED CIRCUIT BOARD LAYOUT Good layout practices will minimize voltage error and prevent instability which can result from ground loops. The input and output capacitors should be directly connected to the IC pins with short traces that have no other current flowing in them (Kelvin connect). The best way to do this is to place the capacitors very near the IC and make connections directly to the IC pins via short traces on the top layer of the PCB. The regulator’s ground pin should be connected through vias to the internal or backside ground plane so that the regulator has a single point ground. The external resistors which set the output voltage must also be located very near the IC with all connections directly tied via short traces to the pins of the IC (Kelvin connect). Do not connect the resistive divider to the load point or DC error will be induced. RFI/EMI SUSCEPTIBILITY RFI (Radio Frequency Interference) and EMI (Electro-Magnetic Interference) can degrade any integrated circuit's performance because of the small dimensions of the geometries inside the device. In applications where circuit sources are present which generate signals with significant high frequency energy content (> 1 MHz), care must be taken to ensure that this does not affect the IC regulator. 12 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ LP38501-ADJ, LP38503-ADJ www.ti.com SNVS522H – AUGUST 2007 – REVISED APRIL 2013 If RFI/EMI noise is present on the input side of the regulator (such as applications where the input source comes from the output of a switching regulator), good ceramic bypass capacitors must be used at the input pin of the IC to reduce the amount of EMI conducted into the IC. If the LP38501/3-ADJ output is connected to a load which switches at high speed (such as a clock), the highfrequency current pulses required by the load must be supplied by the capacitors on the IC output. Since the bandwidth of the regulator loop is less than 300 kHz, the control circuitry cannot respond to load changes above that frequency. This means the effective output impedance of the IC at frequencies above 300 kHz is determined only by the output capacitor(s). Ceramic capacitors provide the best performance in this type of application. In applications where the load is switching at high speed, the output of the IC may need RF isolation from the load. In such cases, it is recommended that some inductance be placed between the output capacitor and the load, and good RF bypass capacitors be placed directly across the load. PCB layout is also critical in high noise environments, since RFI/EMI is easily radiated directly into PC traces. Noisy circuitry should be isolated from "clean" circuits where possible, and grounded through a separate path. At MHz frequencies, ground planes begin to look inductive and RFI/EMI can cause ground bounce across the ground plane. In multi-layer PC Board applications, care should be taken in layout so that noisy power and ground planes do not radiate directly into adjacent layers which carry analog power and ground. OUTPUT NOISE Noise is specified in two waysSpot Noise or Output noise density is the RMS sum of all noise sources, measured at the regulator output, at a specific frequency (measured with a 1Hz bandwidth). This type of noise is usually plotted on a curve as a function of frequency. Total output noise voltage or Broadband noise is the RMS sum of spot noise over a specified bandwidth, usually several decades of frequencies. Attention should be paid to the units of measurement. Spot noise is measured in units µV/√Hz or nV/√Hz and total output noise is measured in µV(rms). The primary source of noise in low-dropout regulators is the internal reference. In CMOS regulators, noise has a low frequency component and a high frequency component, which depend strongly on the silicon area and quiescent current. Noise can generally be reduced in two ways: increase the transistor area or increase the reference current. However, enlarging the transisitors will increase die size, and increasing the reference current means higher total supply current (ground pin current). SHORT-CIRCUIT PROTECTION The LP38501/3-ADJ contains internal current limiting which will reduce output current to a safe value if the output is overloaded or shorted. Depending upon the value of VIN, thermal limiting may also become active as the average power dissipated causes the die temperature to increase to the limit value (about 170°C). The hysteresis of the thermal shutdown circuitry can result in a “cyclic” behavior on the output as the die temperature heats and cools. ENABLE OPERATION (LP38501-ADJ Only) The Enable pin (EN) must be actively terminated by either a 10 kΩ pull-up resistor to VIN, or a driver which actively pulls high and low (such as a CMOS rail to rail comparator). If active drive is used, the pull-up resistor is not required. This pin must be tied to VIN if not used (it must not be left floating). DROPOUT VOLTAGE The dropout voltage of a regulator is defined as the input-to-output differential required by the regulator to keep the output voltage within 2% of the nominal value. For CMOS LDOs, the dropout voltage is the product of the load current and the RDS(on) of the internal MOSFET pass element. Since the output voltage is beginning to “drop out” of regulation when it drops by 2%, electrical performance of the device will be reduced compared to the values listed in the Electrical Characteristics table for some parameters (line and load regulation and PSRR would be affected). Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ Submit Documentation Feedback 13 LP38501-ADJ, LP38503-ADJ SNVS522H – AUGUST 2007 – REVISED APRIL 2013 www.ti.com REVERSE CURRENT PATH The internal MOSFET pass element in the LP38501/3-ADJ has an inherent parasitic diode. During normal operation, the input voltage is higher than the output voltage and the parasitic diode is reverse biased. However, if the output is pulled above the input in an application, then current flows from the output to the input as the parasitic diode gets forward biased. The output can be pulled above the input as long as the current in the parasitic diode is limited to 200 mA continuous and 1A peak. The regulator output pin should not be taken below ground potential. If the LP38501/3-ADJ is used in a dual-supply system where the regulator load is returned to a negative supply, the output must be diode-clamped to ground. POWER DISSIPATION/HEATSINKING The maximum power dissipation (PD(MAX)) of the LP38501/3-ADJ is limited by the maximum junction temperature of 125°C, along with the maximum ambient temperature (TA(MAX)) of the application, and the thermal resistance (θJA) of the package. Under all possible conditions, the junction temperature (TJ) must be within the range specified in the Operating Ratings. The total power dissipation of the device is given by: PD = ( (VIN − VOUT) x IOUT) + (VIN x IGND) where • IGND is the operating ground current of the device (specified under Electrical Characteristics) (3) The maximum allowable junction temperature rise (ΔTJ) depends on the maximum expected ambient temperature (TA(MAX)) of the application, and the maximum allowable junction temperature (TJ(MAX)): ΔTJ = TJ(MAX)− TA(MAX) (4) The maximum allowable value for junction to ambient Thermal Resistance, θJA, can be calculated using the formula: θJA = ΔTJ / PD(MAX) (5) The LP38501/3-ADJ is available in the TO-263 package. The thermal resistance depends on the amount of copper area allocated to heat transfer. HEATSINKING TO-263, PFM THIN PACKAGES The TO-263 package and TO-263 THIN package use the copper plane on the PCB as a heatsink. The DAP of the package is soldered to the copper plane for heat sinking. Figure 26 shows a typical curve for the θJA of the TO-263 package for different copper area sizes (the thermal performance of both the TO-263 and TO-263 THIN are the same). The tests were done using a PCB with 1 ounce copper on top side only which were square in shape. Figure 26. θJA vs Copper Area for TO-263 Package As shown in the figure, increasing the copper area beyond 1.5 square inch produces very little improvement. 14 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ LP38501-ADJ, LP38503-ADJ www.ti.com SNVS522H – AUGUST 2007 – REVISED APRIL 2013 REVISION HISTORY Changes from Revision G (April 2013) to Revision H • Page Changed layout of National Data Sheet to TI format .......................................................................................................... 14 Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LP38501-ADJ LP38503-ADJ Submit Documentation Feedback 15 PACKAGE OPTION ADDENDUM www.ti.com 21-May-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) LP38501ATJ-ADJ/NOPB ACTIVE TO-263 NDQ 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LP38501A TJ-ADJ LP38501TJ-ADJ/NOPB ACTIVE TO-263 NDQ 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LP38501TS-ADJ/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP38501 TS-ADJ LP38501TSX-ADJ/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP38501 TS-ADJ LP38503ATJ-ADJ/NOPB ACTIVE TO-263 NDQ 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LP38503A TJ-ADJ LP38503TJ-ADJ/NOPB ACTIVE TO-263 NDQ 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LP38503 TJ-ADJ LP38503TS-ADJ/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP38503 TS-ADJ LP38503TSX-ADJ/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP38503 TS-ADJ LP38501 TJ-ADJ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com (4) 21-May-2013 There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 29-May-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LP38501ATJ-ADJ/NOPB TO-263 NDQ 5 1000 330.0 24.4 LP38501TJ-ADJ/NOPB 10.6 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 15.4 2.45 12.0 24.0 Q2 TO-263 NDQ 5 1000 330.0 24.4 10.6 15.4 2.45 12.0 24.0 Q2 LP38501TSX-ADJ/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LP38503ATJ-ADJ/NOPB TO-263 NDQ 5 1000 330.0 24.4 10.6 15.4 2.45 12.0 24.0 Q2 LP38503TJ-ADJ/NOPB TO-263 NDQ 5 1000 330.0 24.4 10.6 15.4 2.45 12.0 24.0 Q2 LP38503TSX-ADJ/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-May-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP38501ATJ-ADJ/NOPB TO-263 NDQ 5 1000 367.0 367.0 35.0 LP38501TJ-ADJ/NOPB TO-263 NDQ 5 1000 367.0 367.0 35.0 LP38501TSX-ADJ/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 LP38503ATJ-ADJ/NOPB TO-263 NDQ 5 1000 367.0 367.0 35.0 LP38503TJ-ADJ/NOPB TO-263 NDQ 5 1000 367.0 367.0 35.0 LP38503TSX-ADJ/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA NDQ0005A TJ5A (Rev F) www.ti.com MECHANICAL DATA KTT0005B TS5B (Rev D) BOTTOM SIDE OF PACKAGE www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated