K1300 Series 5V Crystal Clock Oscillators ! ! ! ! ! ! TTL/CMOS Compatible Tri-State Feature for Auto Test Systems Fast Rise and Fall Times 70 to 120 MHz Frequency Range Tight Symmetry (45/55%) Available ax. mM m 8 20, ax. mM m 2 13, 0 HZ E K13000.000 MTE COD 1 TI DA C ±100ppm Stability Standard ±50ppm Stability Available - K1350 m 2m 6,2 x. Ma PIN 1 E L E C T R I C A L S P E C I F I C AT I O N S MODEL K1350 K1300 Frequency Range (MHz) 70 to 120 Frequency Stability (ppm) Overall (Typical) 0°C to 70°C Inclusive of calibration, temperature, voltage, load, shock,vibration, aging ±50 ±100 Temperature Range (°C) Operating 0°C to +70°C Storage -55°C to +125°C Supply Voltage (V) +5.0 ±5% Output TTL Input Current (mA) 50 -80 max Symmetry (%) 40/60 @ 1.4V TR and TF (ns) 5 (0.5V to 2.5V) Fanout 10 Output CMOS 100 max Input Current (mA) Symmetry (%) 40/60 @ 0.5VCC TR and TF (ns) 5 (20% -80 % VCC) Start up Time (ms) TTL <10 CMOS <45 PA R T N U M B E R I N G G U I D E K13XXXX - Specify Frequency “Blank” = TTL Output “C” = CMOS Output “Blank” = 40/60% Symmetry “S” = 45/55% Symmetry (Available to 100MHz. “00” = ±100ppm Stability “50” = ±50ppm 2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585 800-888-1499 or www.champtech.com 1 K1300 Series 5V Crystal Clock Oscillators PIN FUNCTION 1 Tri-State* 2 Ground 3 Output + VCC 4 * Input tied internally to +5V. External input if any, should not be less than +3V and not greater than +3.8V for TTL version. For CMOS models, enable with either an open circuit or +5V. SHIPPING TUBE CROSS SECTION TEST CIRCUIT DIAGRAM OUTPUT WAVEFORM MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS TEST METHODS REFERENCE PROCEDURES DESCRIPTION Temperature Cycle MIL-STD-833, Mtd 1010, Cond. B -55°C to +125°C; Air-to-Air; 100 cycles; 10 min. dwell Mechanical Shock MIL-STD-883, Mtd 2002, Cond. B 1500 g’s Vibration MIL-STD 883, Mtd 2007, Cond. B 20-2000 Hz; 0.06 inch; 15g’s; 3 planes Humidity Steady State MIL-STD-202, Mtd 103 40°C; 90%-95% R.H.; 56 days Thermal Shock MIL-STD-883, Mtd 1011.7 Cond. B 100°C to 0°C; Water-to-Water; 15 cycles Electrostatic Discharge MIL-STD-883, Mtd 3015 Class II 2 KV to 4 KV Threshold Solderability Hermeticity MIL-STD-883, Mtd 2022.2 MIL-STD-883, Mtd 1014.8, Cond. A1 Solder dip; Meniscograph Criteria Mass spectro. 2 x 10-8 atmos. CC/sec He Resistance to Soldering Lead Integrity MIL-STD-202, Mtd 210D, Cond. J 235°C; 30 seconds MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress Marking Permanence Life Test MIL-STD-883, Mtd 2015.8 MIL-STD-883, Mtd 1005.6 Resistance to solvents 125°C, powered, 1000 hours minimum 2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585 800-888-1499 or www.champtech.com 2