Ultra Small SMT Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated Height U.FL Series Meets up to 6 GHz Requirement Mated Height Comparison (With Hirose Product) E.FL-LP-040 E.FL-LP-066 2.4(2.5Max) 1.9(2.0Max) U.FL-LP(V)-040 3(3.2Max) U.FL-LP-040 U.FL-LP-066 U.FL Series ■Features E.FL Series ●Space Factor of Mated Connector 1. Low Profile: 1.9mm or 2.4mm Nom. Mated Height In comparison with our SMT coaxial connectors E.FL series, the receptacle provides a reduction of approximately 18% of occupied mounting surface, which is only 7.7mm2. Dia.0.81 2.Extremely Small Occupied Mounting Area U.FL-LP-040 2.5Max Height from the circuit board is 2.0mm or 2.5mm maximum when a plug (right angle) is mated to a receptacle, which ranks with world’s smallest class. U.FL-R-SMT 3.Light Weight From among the types of applicable cable, dia. 0.81mm(single shielded) ultra-fine Teflon coaxial cable has been made a standard specification in construction area. Refer to the following pages for different cable types. 7.Simple Removal of Connector The extraction jig permits simple removal of connectors. 8.User Friendly Mating Operation NEW Tactile lock feeling ensures engagement even with this small size. Mobile phones, Wireless LAN, Mini-PCI, Bluetooth, PDA, GPS, electronic measuring instruments, etc. Dia.1.32 Dia.1.13 U.FL-R-SMT U.FL-LP-062 U.FL-R-SMT NEW U.FL-LP-088 2.4Max ■Applications U.FL-LP(V)-040 Dia.0.81 6.Use of Ultra-fine Teflon Cable NEW Dia.1.0 Supplied on tape-and-reel packaging. U.FL-R-SMT Dia.1.37 5.Board placement with automatic equipment 2.5Max To meet the frequency requirements of a wide variety of miniature equipment, these connectors offer high frequency performance from DC to 6 GHz. 2.0Max 4.Applicable Up to 6 GHz Frequency U.FL-LP-066 2.4Max One of the world’s lightest coaxial connectors. Receptacle: 15.7mg U.FL-R-SMT 2003.9 1 ■ Product Specifications 50 ohms 60 V AC (rms) DC to 6 GHz Nominal characteristic impedance Voltage rating Frequency range Ratings Item 1. Contact resistance Operating temperature range Operating humidity Specification Conditions Center: 20 m ohms max. 10 mA max. Outside: 10 m ohms max. 2. Insulation resistance 500 M ohms min. 3. Withstanding voltage No flashover or insulation breakdown. 100 V DC 200 V AC / 1 minute Part No. Up to 3GHz 3 to 6GHz U.FL-LP-040 dia.0.81mm Coaxial Cable Assembly 1.3 Max 1.35 Max U.FL-LP(V)-040 dia.0.81mm Coaxial Cable Assembly 1.3 Max 1.3 Max U.FL-LP-066 dia.1.13mm Coaxial Cable Assembly 1.3 Max 1.4 Max U.FL-LP-066 dia.1.32mm Coaxial Cable Assembly 1.3 Max 1.5 Max U.FL-LP-062 dia.1mm Coaxial Cable Assembly 1.3 Max 1.3 Max 1.3 Max 1.4 Max 4. V.S.W.R.* U.FL-LP-088 dia.1.37mm Coaxial Cable Assembly 5. Female contact holding force 0.15 N min. 6. Durability -40˚C to +90˚C 90% max. Measured with a Ø 0.475 pin gauge Contact resistance (mating/un-mating, Center: 25 m ohms max. with corresponding plug) Outside: 15 m ohms max. 30 cycles Frequency: 10 to 100 Hz, single amplitude of 1.5mm, acceleration 7. Vibration No electrical discontinuity of 1µs min. of 59m/s2, for 5 cycles in the direction of each of the 3 axis. 8. Shock No damage, cracks or parts dislocation. Acceleration of 735 m/s2, 11ms duration, sine half-wave 9. Humidity No damage, cracks or parts dislocation. waveform, 2 cycles in each of 3 axes. (Steady state) Insulation resistance 100 M ohms min.(when humidity high) 96 hours at temperature of 40ç and humidity of 95%. Insulation resistance 500 M ohms min.(when dry) 10. Temperature cycle No damage, cracks or parts dislocation. Temperature:-40˚C/+5 to +35˚C/+90˚C/+5 to +35˚C Contact resistance:25 m ohms max. (Center) Time: 15 m ohms max. (Outside) 11. Salt spray test 30 / 5 max. /30 /5 max.(Minutes) 5 cycles 5% salt water solution, 48 hours No excessive corrosion *V.S.W.R. Measurement System The above V.S.W.R. standard values were measured using the measurement system of the diagram below. Note 1: Cable type connectors were measured with SMA conversion adapters attached to both ends of the harness product of a suitable 100cm cable. Note 2: Board type connectors were mounted to a 50Ω glass epoxy board and measurements were conducted with SMA conversion adapters attached. ■Materials Part Material Finish Shell Phosphor bronze Silver plating ————— Male center contact Brass Gold plating ————— Female center contact Phosphor bronze Gold plating ————— Insulator 2 Remarks Plug PBT Color: Black UL94V-0 Receptacle LCP Color: Beige UL94V-0 ■Cable Assembly (Plug) Part No. 5 1.8 1.5 1.93 1.93 Mated Height 4 3.4 4 1.85 4 U.FL-LP-088 3 3 U.FL-LP-062 2.8 U.FL-LP(V)-040 2.8 U.FL-LP-066 3 U.FL-LP-040 2.5mm Max. 2.5mm Max. 2.0mm Max. 2.4mm Max. 2.4mm Max. (2.4mm Nom.) (2.4mm Nom.) (1.9mm Nom.) (2.3mm Nom.) (2.3mm Nom.) Applicable Dia. 0.81mm cable Coaxial cable Weight (mg) 53.7 Dia. 1.13mm and Dia. 1.32mm Coaxial cable 59.1 Dia. 0.81mm Dia. 1mm Dia. 1.37mm Coaxial cable Coaxial cable Coaxial cable 34.8 45.5 71.7 ●Cable Guide Description Dia.0.81mm Coaxial Cable Dia.1.32mm Coaxial Cable Dia.1mm Coaxial Cable Dia.1.37mm Coaxial Cable Jacket Diameter Dia.0.40 Single Dia.0.81 PFA Shield SA PFA 7/0.08 SA Dia.0.68 Single Dia.1.13 (AWG32) FEP Shield SA[TA] FEP 7/0.08 SA Dia.0.66 Double Dia.1.32 (AWG32) FEP Shield TA FEP 7/0.071 SA Dia.0.62 Tape, single Dia.1 (AWG33) FEP Shield TAT FEP 7/0.102 SA Dia.0.88 Single Dia.1.37 (AWG30) FEP Shield TA FEP 066 088 Outer Coaxial cableConductor* Diameter (AWG36) 068 062 Dia. 0.81mm Dielectric 7/0.05 SA 04 Coaxial Cable Dia.1.13mm Cable Specification CableDia. 0.81mm Inner TypeCoaxial cable * Conductor Dia. 1mm 1.37mm Nominal Dia. attenuation Nominal Coaxial cable Coaxial cable Impedance At 3GHz At 6GHz 50 ohms 6.45dB/m 9.42dB/m 3.43dB/m 5.13dB/m [3.73dB/m] [5.44dB/m] 50 ohms 3.8dB/m 5.6dB/m 50 ohms 3.1dB/m 4.4dB/m 50 ohms 2.8dB/m 4.3dB/m 50 ohms (data as provided by material suppliers, for reference only) * SA : Silver plated annealed copper wire, TA : Tin plated annealed copper wire, TAT : Tin plated copper wire alloyed with tin ■How to Specify Cable Assembled Plug Dimension of U.FL Series assembly products should be made as indicated below. Single-Ended Cable Assembly Double-Ended Cable Assembly L L ●Total Standard Tolerance for Total Length of Cable Assembly ●Ordering Information U.FL - [] LP - [] - A - (L) 1 2 3 1 Series name U.FL 2 Assembly type LP: Single ended 2LP: Double ended 4 3 Cable type 04 : Dia.0.81mm Coaxial Cable 068 : Dia.1.13mm Coaxial Cable 066 : Dia.1.32mm Coaxial Cable 062 : Dia.1 mm Coaxial Cable 088 : Dia.1.37mm Coaxial Cable 4 Total Length(mm) Length is expressed in mm units. Total Length(mm) 00350< =L< =00200 Standard Tolerance (mm) 02000<L< =00500 < 05000<L =01000 ±08 10000<0L< =1000 ±04 ±12 ±1.5% Note: Shortest length L is 35 mm. Please contact Hirose Sales Representative for cable length and cable end treatment. 3 ■Receptacles Cut Out Prohibition Area GND 4±0.05 1.9±0.05 GND SIG 1.05±0.05 Weight (mg) Packaging Part No. CL No. 331-0471-0-01 Bag packaging (100 pieces/bag) U.FL-R-SMT(10) 331-0471-0-10 Reel packaging (2500 pieces/reel) 15.7/unit ●Packaging Specifications 0.3 Center contact 5.5±0.1 1 0. + 0 .5 12±0.3 Ø1 1.75±0.1 Embossed Carrier Tape Dimensions 4±0.1 8±0.1 1.6 Unreeling direction Reel Dimensions 1.8 14 Ø13 Ø330±2 Ø21 4 GND SIG 1±0.05 Recommended PCB Footprints U.FL-R-SMT(01) 2±0.1 2.2±0.05 1.2Max(NOTE 3) 1.25 0.35 2.6 1.8 (3.1) Note 1: Receptacles of (01) specification are sold by the pack with 100 pieces per pack. Please order in pack units. Note 2: Receptacles of (10) specification are sold by the reel (which contains 2,500 pieces). Please order in reel units. Note 3: Permissible value for mold resin which gets onto the center contact. 3 2.6 0.6 1±0.05 GND Ø2 ■Conversion Adapter ●SMA Conversion Adapter (Mating portion: U.FL side jack - SMA side plug) (10.7) 8HEX Ø1.9 1.1 Note: The U.FL side mating portions has a lower lock retention force than the regular product, therefore, cannot be used for purposes other than performance measurements. Part No. CL No. HRMP-U.FLJ 311-0300-2 ●SMA Conversion Adapter (Mating portion: U.FL side plug - SMA side jack) 14.05 (4.05) 5.6 Ø6.35 6 1/4-36UNS-2A Note: The U.FL side mating portions has a lower lock retention force than the regular product, therefore, cannot be used for purposes other than performance measurements. ●SMA Conversion Adapter (Mating portion: U.FL side plug-SMA side jack) Part No. CL No. HRMJ-U.FLP 311-0301-5 (18.6) (4) 6 5.5 1/4-36UNS-2A Note: This connector is used by compressing the mated portion of U.FL side onto the U.FL-R-SMT portion. Part No. CL No. HRMJ-U.FLP-ST1 311-0385-5 ■Receptacle for Check 12.9 This receptacle is used for inspecting the continuity, withstand voltage, and other aspects of the harness product. (7.9) (4.4) 7HEX 5 1 M5×0.5 This receptacle is used for check the continuity, withstanding voltage, and other performance of the cable assembly products. Part No. CL No. U.FL-R-1 331-0466-0 ■Extraction Jig (90) This jig is used for extraction from a mating condition. Ø15 U.FL 2.1 5 50 Note: Part No. U.FL-LP-N-2 for U.FL-LP-040/066/088. Part No. U.FL-LP(V)-N-2 for U.FL-LP(V)-040/U.FL-LP-062. Part No. CL No. U.FL-LP-N-2 331-0494-5 U.FL-LP(V)-N-2 331-0493-2 5 ■Usage Precautions 1. Plugs (1) Connection/ disconnection of connectors 1) To disconnect connectors, hook the end portion of U.FL-LP-N-2 and U.FL-LP(V)-N-2 onto the connector cover and pull off vertically in the direction of the connector mating axis. 1) To remove the connector directly, hold the connector cover and pull off Extraction Jig vertically in the direction of the connector mating axis. U.FL Cable (Please exercise caution so as not to injure fingertips or nails.) Assembly 2) To mate the connectors, the mating axes of both connectors are aligned and the connectors are inserted as perpendicularly as possible. Do not attempt to insert on an extreme angle. U.FL-R-SMT After the connectors are mating, do not apply a load to the cable in excess of the values indicated in the diagram below. U.FL-LP-040 2N max. U.FL-R-SMT (2) Permissible load on the cable after connector mating. 4N max. 2N max. (3) Precautions Do NOT forcefully twist or deform wires. Temperature on Top Portion of Part 2. Receptacles (1) Recommended temperature profile (Reference) (℃) 260 240 220 200 180 160 140 120 100 80 Heating peak 240℃ 3 seconds Preheating 183℃ (130 to 165℃) Within 2 minutes 40 to 50 seconds Time 1) The temperature profile indicates the board surface temperature at the point of contacts with the connector terminals (for surface mounted receptacle). 2) The temperature profile will change depending on conditions which include such factors as the size of the board, the solder used, and the solder thickness. (2) Recommended manual soldering (Reference) Manual soldering: 350˚C for 5 seconds (3) Recommended screen 0.1 to 0.15 mm thickness 6 NOTES : 7 USA: HIROSE ELECTRIC U.S.A., INC. 2688 Westhills Court, Simi Valley, CA 93065-6235 Phone : 1 805 522 7958 Fax : 1 805 522 3217 http://www.hirose.com EUROPE BRANCH: HIROSE ELECTRIC CO., LTD. Beechavenue 46.1119PV Schiphol-Rijk,The Netherlands Phone : 31 20 6557460 Fax : 31 20 6557469 http://hiroseeurope.com GERMANY: HIROSE ELECTRIC GmbH Zeppelinstrasse 42 D-73760 Ostfildern Kemnat Phone : 49 711 4560021 Fax : 49 711 4560729 http://www.hirose.de UNITED KINGDOM: KOREA: HIROSE ELECTRIC UK LTD. HIROSE KOREA CO., LTD. Crownhill Business Centre 22 Vincent Avenue (#2NA311,Shihwa Industrial Complex), Crownhill, Milton Keynes MK8 OAB 1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do Phone : 44 1908 305400 Phone : 82 31 496 7000,7124 Fax : 44 1908 305401 Fax : 82 31 496 7100 http://www.hirose.co.uk http://www.hirose.co.kr CHINA: HIROSE ELECTRIC TRADING(SHANGHAI) CO., LTD. 3705,Bund Center,222 Yan An Road(E),Shanghai 20002 Phone : 86 21 6335 2538 Fax : 86 21 6335 0767 HONG KONG: HIROSE ELECTRIC CO., LTD. Unit 506, Energy Plaza. 92 Granville Road, Tsim Sha Tsui East, Kowloon Phone : 852 2803 5338 Fax : 852 2591 6560 SINGAPORE: HIROSE ELECTRIC CO., LTD. 10 Anson Road #34-13 International Plaza 079903 Phone : 65 6324 6113 Fax : 65 6324 6123 TAIWAN: HIROSE ELECTRIC CO., LTD. No.28 Lane 247 Sec. 2 Yen Ping N,Rd.Taipei Phone : 886 2 2557 7351,7352 Fax : 886 2 2552 9851 ® 5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933 8 The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.