CT CTDD2727DF-2415-D1K-5 Dc/dc converter Datasheet

DC/DC Converters
SPECIFICATIONS
CTDD2727DF-D1K-5 Series
Wide Input Isolated & Regulated
5W Output, Dual Output
Not shown at actual size.
RoHS
Compliant
ctparts.com
Vin
Nom.
(VDC)
Input Range
(VDC)
Vin
Max.*
(VDC)
Vout
(VDC)
CTDD2727DF-1205-D1K-5
CTDD2727DF-1209-D1K-5
CTDD2727DF-1212-D1K-5
CTDD2727DF-1215-D1K-5
12
12
12
12
9-18
9-18
9-18
9-18
22
22
22
22
±5
±9
±12
±15
CTDD2727DF-1505-D1K-5
CTDD2727DF-1512-D1K-5
CTDD2727DF-1515-D1K-5
15
15
15
12-24
12-24
12-24
30
30
30
CTDD2727DF-2405-D1K-5
CTDD2727DF-2409-D1K-5
CTDD2727DF-2412-D1K-5
CTDD2727DF-2415-D1K-5
24
24
24
24
18-36
18-36
18-36
18-36
CTDD2727DF-4805-D1K-5
CTDD2727DF-4809-D1K-5
CTDD2727DF-4812-D1K-5
CTDD2727DF-4815-D1K-5
48
48
48
48
36-72
36-72
36-72
36-72
Part
Number
Iout
Max.
(mA)
Iout
Min**.
(mA)
Effi.
Typ.
(%)
±500
±278
±210
±166
±50
±28
±21
±17
72
75
77
80
±5
±12
±15
±500
±210
±166
±50
±21
±17
75
80
81
40
40
40
40
±5
±9
±12
±15
±500
±278
±210
±166
±50
±28
±21
±17
77
80
82
84
80
80
80
80
±5
±9
±12
±15
±500
±278
±210
±166
±50
±28
±21
±17
79
82
85
85
*If Input voltage above specified may cause permanent damage to the device
**The load should not be less than 10%, otherwise ripple will increase dramatically
ISOLATION SPECIFICATIONS
Item
Test Condition
MIN
Isolation Voltage
Flash tested for 1 minute
1000
VDC
Test at 500VDC
1000
MΩ
Isolation Resistance
TYP
MAX
Units
FEATURES
CHARACTERISTICS
Output Short Circuit Protection: Continuous
Temperature Rise at Full Load: 30°C (Typ.)
Cooling: Free air convection
No Load, Power Consumption: 500mW (typical)
Operating Temperature Range: -40°C to +85°C
Storage Temperature Range: -55°C to +125°C
Lead Temperature: 300°C (1.5mm from case for 10 seconds)
Storage Humidity Range: < 95%
Case Material: Metal
MTBF: >3,500,000 hours
Miscellaneous: RoHS Compliant.
OUTPUT SPECIFICATIONS
Item
Test Condition
5W Output Power
MAX
Units
5
W
Refer to Recommended Circuit
±1
±3
%
Negative voltage accuracy
Refer to Recommended Circuit
±3
±5
%
Load regulation
From 10% to 100% load
±0.1
±0.2
%
Line regulation
Input Voltage from low to high
±0.2
±0.5
%
Temperature drift (Vout)
Refer to Temp. Derating Graph
Ripple
20Hz to 300KHz Bandwidth
Noise
DC-20MHz Bandwidth
Switching frequency
100% load, nominal input voltage
80
Switching frequency
10% load, nominal input voltage
250
0.03
%/°C
30
50
mVp-p
80
150
mVp-p
200
KHz
600
KHz
Note:
1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output unless
otherwise specified.
TYPICAL CHARACTERISTICS
Temperature Derating Graph
120
100
80
60
40
Safe Operating Area
20
0
120
40
71 85
Ambient Temperature (°C)
01.05.07
Technologies
TYP
0.5
0
-40
CENTRAL
MIN
Positive voltage accuracy
Output Power (%)
Efficiency: To 85%
Temperature Range: -40°C to +85°C
Isolation: 1KVDC
Miscellaneous: Wide (2:1) Input Range. Metal Shielding
Package. No heat sink required. Industry Standard Pinout. Dual
Output. Custom service available.
Samples available.
Manufacturer of Passive and Discrete Semiconductor Components
800-684-5322 Inside US
949-453-1811 Outside US
Copyright © 2006 by CT Magnetics, DBA Central Technologies. All rights reserved.
CT Magnetics reserves the right to make improvements or change specifications without notice
DC/DC Converters
ctparts.com
CTDD2727DF-D1K-5 Series
Wide Input Isolated & Regulated
5W Output, Dual Output
OUTLINE DIMENSIONS & RECOMMENDED FOOTPRINT DETAILS
CTDD2727DF-D1K-5 Package
27.50
9.00
Side View
4.00
20.32
4
5
3
27.50
Top View
1 2
5.08
CTDD2727DF-D1K-5 Footprint
2.54
1.60ø+0.15/-0
5
4
1
3
2
2.54
Note: All Pins on a 2.54m pitch; all pin diameters are 0.50mm; all dimensions in mm.
PIN CONNECTIONS
Pin Function
1
2
3
4
5
3
4
5
Vin
GND
+Vo
OV
-V0
Top View
1 2
RECOMMENDED CIRCUIT
All the CTDD2727DF-D1K-5 Series have been tested according to the following recommended testing circuit before leaving
factory. This series should be tested under load. Never be tested under no load (See figure 1 & 2). If you want to further
decrease the input/output ripple, you can increase capacitance properly or choose capacitors with low ESR. However, the
capacitance should not be too high (See table 1). If you want to use the products in high EMI, please choose our metal
packaged products.
External Capacitor Table (table 1)
Figure 2
5V
&
12V
24V
&
48V
C in
100µF
C out
(0+70°C)
100µF
(electrolytic
capacitor)
C out
(-40+85°C)
47µF
(tantalum
capacitor)
lp
Figure 1
Vin
+Cin
DC
DC
10µF
Cout
+
Cout
+
Vout+
0V
Input Current (A)
Vin
Input Voltage
Range
Vo-
GND
Input Voltage (V)
CENTRAL
Technologies
01.05.07
Manufacturer of Passive and Discrete Semiconductor Components
800-684-5322 Inside US
949-453-1811 Outside US
Copyright © 2006 by CT Magnetics, DBA Central Technologies. All rights reserved.
CT Magnetics reserves the right to make improvements or change specifications without notice
Similar pages