LD29080 SERIES 800mA FIXED AND ADJUSTABLE OUTPUT VERY LOW DROP VOLTAGE REGULATOR PRELIMINARY DATA ■ ■ ■ ■ ■ VERY LOW DROPOUT VOLTAGE (TYP. 0.4V AT 800mA) GUARANTEED OUTPUT CURRENT UP TO 800mA FIXED AND ADJUSTABLE OUTPUT VOLTAGE (±1% AT 25°C) INTERNAL CURRENT AND THERMAL LIMIT LOGIC CONTROLLED ELECTRONIC SHUTDOWN DESCRIPTION The LD29080 is a high current, high accuracy, low-dropout voltage regulators series. These regulators feature 400mV dropout voltages and very low ground current. Designed for high current loads, these devices also find applications in lower current, extremely low dropout-critical systems, where their tiny dropout voltage and ground current values are important attributes. Typical application are in Power supply switching post PPAK DPAK SOT-223 regulation, Series power supply for monitors, Series power supply for VCRs and TVs, Computer Systems and Battery powered systems. Figure 1: Schematic Diagram For Adjustable Version October 2004 Rev. 1 1/21 This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. LD29080 SERIES Figure 2: Schematic Diagram For Fixed Version Table 1: Ordering Codes DPAK (*) PPAK (*) SOT-223 OUTPUT VOLTAGE LD29080DT15 LD29080DT18 LD29080DT25 LD29080DT33 LD29080DT50 LD29080DT80 LD29080DT90 LD29080PT15 LD29080PT18 LD29080PT25 LD29080PT33 LD29080PT50 LD29080PT80 LD29080PT90 LD29080PT LD29080S15 LD29080S18 LD29080S25 LD29080S33 LD29080S50 LD29080S80 LD29080S90 1.5 V 1.8 V 2.5 V 3.3 V 5.0 V 8.0 V (**) 9.0 V (**) ADJ (*) Available in Tape & Reel with the suffix "R", for the adj version "-R" (**) Available on Request Table 2: Absolute Maximum Ratings Symbol VI VINH Parameter DC Input Voltage Inhibit Input Voltage Value Unit 30 (*) V 14 V IO Output Current Internally Limited mA PD Power Dissipation Internally Limited mW Tstg Storage Temperature Range -55 to 150 °C Top Storage Temperature Range -40 to 125 °C (*) Above 14V the device is automatically in shut-down. Absolute Maximum Ratings are those beyond which damage to the device may occur. Functional operation under these condition is not implied. 2/21 LD29080 SERIES Table 3: Thermal Data Symbol Parameter Rthj-case Thermal Resistance Junction-case Rthj-amb Thermal Resistance Junction-ambient DPAK PPAK SOT-223 Unit 8 8 15 °C/W 100 100 °C/W Figure 3: Pin Connection (top view) PPAK DPAK SOT-223 Table 4: Pin Description Symbol PPAK DPAK SOT-223 VI 2 1 1 GND VO 3 4 2 3 2 3 ADJ/N.C.** INHIBIT* 5 1 * Not internally pulled up; in order to assure the operating condition (device in ON mode), it must be connected to a positive voltage higher than 2V. ** Not connect for fixed version. 3/21 LD29080 SERIES Figure 4: Application Circuit R1 VO = VREF (1 + ) R2 * Only for version with inhibit function. Table 5: Electrical Characteristics Of LD29080#15 (IO = 10mA (Note 4), TJ = 25°C, VI = 3.5V, VINH = 2V, CI = 330nF, CO = 10µF, unless otherwise specified) Symbol Parameter Test Conditions VI Operating Input Voltage IO = 10mA to 800mA VO Output Voltage IO = 10mA to 800mA, VI = 3 to 7V TJ = -40 to 125°C Min. Typ. Max. 13 V 1.5 1.515 1.537 V 2.5 1.485 1.463 Unit ∆VO Load Regulation IO = 10mA to 800mA 0.2 1.0 % ∆VO Line Regulation VI = 3 to 13V 0.06 0.5 % SVR Supply Voltage Rejection f = 120 Hz, VI = 3.5 ± 1V, IO = 400mA (Note 1) IO = 10mA, TJ = -40 to 125°C Iq Quiescent Current 65 75 dB 2 5 8 20 IO = 400mA, TJ = -40 to 125°C IO = 800mA, TJ = -40 to 125°C 14 35 TJ = -40 to 125°C 130 180 Isc Short Circuit Current VI = 13V, VINH = GND RL = 0 VIL Control Input Logic Low OFF MODE TJ = -40 to 125°C 1.2 VIH Control Input Logic High ON MODE TJ = -40 to 125°C IINH Control Input Current VINH = 13V TJ = -40 to 125°C eN Output Noise Voltage BP = 10Hz to 100KHzIO = 100mA mA µA A 0.8 V 10 µA 2 V 5 60 µVRMS NOTE 1: Guaranteed by design. NOTE 2: Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. NOTE 3: Reference Voltage is measured between output and GND pins, with ADJ PIN tied to VOUT. NOTE 4: in order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2mA is required. 4/21 LD29080 SERIES Table 6: Electrical Characteristics Of LD29080#18 (IO = 10mA (Note 4), TJ = 25°C, VI = 3.5V, VINH = 2V, CI = 330nF, CO = 10µF, unless otherwise specified) Symbol Parameter Test Conditions VI Operating Input Voltage IO = 10mA to 800mA VO Output Voltage IO = 10mA to 800mA, VI = 3 to 7.3V TJ = -40 to 125°C ∆VO Load Regulation IO = 10mA to 800mA ∆VO Line Regulation VI = 3 to 13V SVR Supply Voltage Rejection f = 120 Hz, VI = 3.8 ± 1V, IO = 400mA (Note 1) IO = 150mA,TJ = -40 to 125°C (Note 2) VDROP Iq Dropout Voltage Quiescent Current Min. Typ. Max. Unit 13 V 1.8 1.818 1.845 V 0.2 1.0 % 0.06 0.5 2.5 1.782 1.755 62 dB 0.1 V IO = 400mA,TJ = -40 to 125°C (Note 2) 0.2 IO = 800mA,TJ = -40 to 125°C (Note 2) 0.4 0.7 IO = 10mA, TJ = -40 to 125°C 2 5 IO = 400mA, TJ = -40 to 125°C 8 20 IO = 800mA, TJ = -40 to 125°C 14 35 VI = 13V, VINH = GND RL = 0 TJ = -40 to 125°C 130 180 Isc Short Circuit Current VIL Control Input Logic Low OFF MODE TJ = -40 to 125°C VIH Control Input Logic High ON MODE TJ = -40 to 125°C 1.2 TJ = -40 to 125°C IINH Control Input Current VINH = 13V eN Output Noise Voltage BP = 10Hz to 100KHzIO = 100mA % 72 mA µA A 0.8 2 V V 5 72 10 µA µVRMS NOTE 1: Guaranteed by design. NOTE 2: Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. NOTE 3: Reference Voltage is measured between output and GND pins, with ADJ PIN tied to VOUT. NOTE 4: in order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2mA is required. 5/21 LD29080 SERIES Table 7: Electrical Characteristics Of LD29080#25 (IO = 10mA (Note 4), TJ = 25°C, VI = 4.5V, VINH = 2V, CI = 330nF, CO = 10µF, unless otherwise specified) Symbol Parameter Test Conditions VI Operating Input Voltage IO = 10mA to 800mA VO Output Voltage IO = 10mA to 800mA, VI = 3.5 to 8V TJ = -40 to 125°C ∆VO Load Regulation IO = 10mA to 800mA ∆VO Line Regulation VI = 3.5 to 13V SVR Supply Voltage Rejection f = 120 Hz, VI = 4.5 ± 1V, IO = 400mA (Note 1) IO = 150mA,TJ = -40 to 125°C (Note 2) VDROP Iq Dropout Voltage Quiescent Current Min. 2.475 2.438 55 Typ. Max. Unit 13 V 2.5 2.525 2.562 V 0.2 1.0 % 0.06 0.5 dB 0.1 V IO = 400mA,TJ = -40 to 125°C (Note 2) 0.2 IO = 800mA,TJ = -40 to 125°C (Note 2) 0.4 0.7 IO = 10mA, TJ = -40 to 125°C 2 5 IO = 400mA, TJ = -40 to 125°C 8 20 IO = 800mA, TJ = -40 to 125°C 14 35 VI = 13V, VINH = GND RL = 0 TJ = -40 to 125°C 130 180 Isc Short Circuit Current VIL Control Input Logic Low OFF MODE TJ = -40 to 125°C VIH Control Input Logic High ON MODE TJ = -40 to 125°C 1.2 TJ = -40 to 125°C IINH Control Input Current VINH = 13V eN Output Noise Voltage BP = 10Hz to 100KHzIO = 100mA % 70 mA µA A 0.8 2 V V 5 100 10 µA µVRMS NOTE 1: Guaranteed by design. NOTE 2: Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. NOTE 3: Reference Voltage is measured between output and GND pins, with ADJ PIN tied to VOUT. NOTE 4: in order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2mA is required. 6/21 LD29080 SERIES Table 8: Electrical Characteristics Of LD29080#33 (IO = 10mA (Note 4), TJ = 25°C, VI = 5.3V, VINH = 2V, CI = 330nF, CO = 10µF, unless otherwise specified) Symbol Parameter Test Conditions VI Operating Input Voltage IO = 10mA to 800mA VO Output Voltage IO = 10mA to 800mA, VI = 4.3 to 8.8V TJ = -40 to 125°C ∆VO Load Regulation IO = 10mA to 800mA ∆VO Line Regulation VI = 4.3 to 13V SVR Supply Voltage Rejection f = 120 Hz, VI = 5.3 ± 1V, IO = 400mA (Note 1) IO = 150mA,TJ = -40 to 125°C (Note 2) VDROP Iq Dropout Voltage Quiescent Current Min. 3.267 3.218 52 Typ. Max. Unit 13 V 3.3 3.333 3.382 V 0.2 1.0 % 0.06 0.5 dB 0.1 V IO = 400mA,TJ = -40 to 125°C (Note 2) 0.2 IO = 800mA,TJ = -40 to 125°C (Note 2) 0.4 0.7 IO = 10mA, TJ = -40 to 125°C 2 5 IO = 400mA, TJ = -40 to 125°C 8 20 IO = 800mA, TJ = -40 to 125°C 14 35 VI = 13V, VINH = GND RL = 0 TJ = -40 to 125°C 130 180 Isc Short Circuit Current VIL Control Input Logic Low OFF MODE TJ = -40 to 125°C VIH Control Input Logic High ON MODE TJ = -40 to 125°C 1.2 TJ = -40 to 125°C IINH Control Input Current VINH = 13V eN Output Noise Voltage BP = 10Hz to 100KHzIO = 100mA % 67 mA µA A 0.8 2 V V 5 132 10 µA µVRMS NOTE 1: Guaranteed by design. NOTE 2: Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. NOTE 3: Reference Voltage is measured between output and GND pins, with ADJ PIN tied to VOUT. NOTE 4: in order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2mA is required. 7/21 LD29080 SERIES Table 9: Electrical Characteristics Of LD29080#50 (IO = 10mA (Note 4), TJ = 25°C, VI = 7V, VINH = 2V, C I = 330nF, CO = 10µF, unless otherwise specified) Symbol Parameter Test Conditions VI Operating Input Voltage IO = 10mA to 800mA VO Output Voltage IO = 10mA to 800mA, VI = 6 to 10.5V TJ = -40 to 125°C ∆VO Load Regulation IO = 10mA to 800mA ∆VO Line Regulation VI = 6 to 13V SVR Supply Voltage Rejection f = 120 Hz, VI = 7 ± 1V, IO = 400mA (Note 1) IO = 150mA,TJ = -40 to 125°C (Note 2) VDROP Iq Dropout Voltage Quiescent Current Min. 4.95 4.875 49 Typ. Max. Unit 13 V 5 5.05 5.125 V 0.2 1.0 % 0.06 0.5 dB 0.1 V IO = 400mA,TJ = -40 to 125°C (Note 2) 0.2 IO = 800mA,TJ = -40 to 125°C (Note 2) 0.4 0.7 IO = 10mA, TJ = -40 to 125°C 2 5 IO = 400mA, TJ = -40 to 125°C 8 20 IO = 800mA, TJ = -40 to 125°C 14 35 VI = 13V, VINH = GND TJ = -40 to 125°C RL = 0 130 180 Isc Short Circuit Current VIL Control Input Logic Low OFF MODE TJ = -40 to 125°C VIH Control Input Logic High ON MODE TJ = -40 to 125°C TJ = -40 to 125°C IINH Control Input Current VINH = 13V eN Output Noise Voltage BP = 10Hz to 100KHzIO = 100mA % 64 1.2 mA µA A 0.8 2 V V 5 320 10 µA µVRMS NOTE 1: Guaranteed by design. NOTE 2: Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. NOTE 3: Reference Voltage is measured between output and GND pins, with ADJ PIN tied to VOUT. NOTE 4: in order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2mA is required. 8/21 LD29080 SERIES Table 10: Electrical Characteristics Of LD29080#80 (IO = 10mA (Note 4), TJ = 25°C, VI = 10V, VINH = 2V, CI = 330nF, CO = 10µF, unless otherwise specified) Symbol Parameter Test Conditions VI Operating Input Voltage IO = 10mA to 800mA VO Output Voltage IO = 10mA to 800mA, VI = 9 to 13V TJ = -40 to 125°C ∆VO Load Regulation IO = 10mA to 800mA ∆VO Line Regulation VI = 9 to 13V SVR Supply Voltage Rejection f = 120 Hz, VI = 9 ± 1V, IO = 400mA (Note 1) IO = 150mA,TJ = -40 to 125°C (Note 2) VDROP Iq Dropout Voltage Quiescent Current Min. 7.92 7.80 45 Typ. Max. Unit 13 V 8 8.08 8.20 V 0.2 1.0 % 0.06 0.5 dB 0.1 V IO = 400mA,TJ = -40 to 125°C (Note 2) 0.2 IO = 800mA,TJ = -40 to 125°C (Note 2) 0.4 0.7 IO = 10mA, TJ = -40 to 125°C 2 5 IO = 400mA, TJ = -40 to 125°C 8 20 IO = 800mA, TJ = -40 to 125°C 14 35 VI = 13V, VINH = GND RL = 0 TJ = -40 to 125°C 130 180 Isc Short Circuit Current VIL Control Input Logic Low OFF MODE TJ = -40 to 125°C VIH Control Input Logic High ON MODE TJ = -40 to 125°C 1.2 TJ = -40 to 125°C IINH Control Input Current VINH = 13V eN Output Noise Voltage BP = 10Hz to 100KHzIO = 100mA % 59 mA µA A 0.8 2 V V 5 320 10 µA µVRMS NOTE 1: Guaranteed by design. NOTE 2: Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. NOTE 3: Reference Voltage is measured between output and GND pins, with ADJ PIN tied to VOUT. NOTE 4: in order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2mA is required. 9/21 LD29080 SERIES Table 11: Electrical Characteristics Of LD29080#90 (IO = 10mA (Note 4), TJ = 25°C, VI = 11V, VINH = 2V, CI = 330nF, C O = 10µF, unless otherwise specified) Symbol Parameter Test Conditions VI Operating Input Voltage IO = 10mA to 800mA VO Output Voltage IO = 10mA to 800mA, VI = 10 to 13V TJ = -40 to 125°C ∆VO Load Regulation IO = 10mA to 800mA ∆VO Line Regulation VI = 10 to 13V SVR Supply Voltage Rejection f = 120 Hz, VI = 11 ± 1V, IO = 400mA (Note 1) IO = 150mA,TJ = -40 to 125°C (Note 2) VDROP Iq Dropout Voltage Quiescent Current Min. 8.91 8.775 45 Typ. Max. Unit 13 V 9 9.09 9.225 V 0.2 1.0 % 0.06 0.5 dB 0.1 V IO = 400mA,TJ = -40 to 125°C (Note 2) 0.2 IO = 800mA,TJ = -40 to 125°C (Note 2) 0.4 0.7 IO = 10mA, TJ = -40 to 125°C 2 5 IO = 400mA, TJ = -40 to 125°C 8 20 IO = 800mA, TJ = -40 to 125°C 14 35 VI = 13V, VINH = GND TJ = -40 to 125°C RL = 0 130 180 Isc Short Circuit Current VIL Control Input Logic Low OFF MODE TJ = -40 to 125°C VIH Control Input Logic High ON MODE TJ = -40 to 125°C TJ = -40 to 125°C IINH Control Input Current VINH = 13V eN Output Noise Voltage BP = 10Hz to 100KHzIO = 100mA % 58 1.2 mA µA A 0.8 2 V V 5 360 10 µA µVRMS NOTE 1: Guaranteed by design. NOTE 2: Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. NOTE 3: Reference Voltage is measured between output and GND pins, with ADJ PIN tied to VOUT. NOTE 4: in order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2mA is required. 10/21 LD29080 SERIES Table 12: Electrical Characteristics Of LD29080#ADJ (IO = 10mA (Note 4), TJ = 25°C, VI = 3.23 V, VINH = 2V, CI = 330nF, C O = 10µF adjust pin tied to output pin, unless otherwise specified) Symbol VI Parameter Test Conditions ∆VO Minimum Operating Input Voltage Load Regulation IO = 10mA to 800mA ∆VO Line Regulation VI = 2.5 V to 13V VREF Reference Voltage IO = 10mA to 800mA, VI = 2.5 to 6.73V TJ = -40 to 125°C (Note 3) SVR Supply Voltage Rejection f = 120 Hz, VI = 3.23 ± 1V, IO = 400mA (Note 1) IO = 10mA, TJ = -40 to 125°C IO = 400mA, TJ = -40 to 125°C Iq Quiescent Current IO = 10mA to 800mA Typ. 2.5 Max. Unit 13 V 0.2 1.0 % 0.06 0.5 % 1.2177 1.1993 1.23 1.2423 1.2607 V 45 75 IO = 10mA dB 2 5 mA 8 20 TJ = -40 to 125°C 14 35 VI = 13V, VINH = GND TJ = -40 to 125°C 130 180 µA 1 µA IO = 800mA, IADJ Min. Adjust Pin Current TJ = -40 to 125°C (Note 1) Isc Short Circuit Current RL = 0 VIL Control Input Logic Low OFF MODE TJ = -40 to 125°C 1.2 VIH Control Input Logic High ON MODE TJ = -40 to 125°C IINH Control Input Current VINH = 13V TJ = -40 to 125°C eN Output Noise Voltage BP = 10Hz to 100KHzIO = 100mA A 0.8 V 10 µA 2 V 5 50 µVRMS NOTE 1: Guaranteed by design. NOTE 2: Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. NOTE 3: Reference Voltage is measured between output and GND pins, with ADJ PIN tied to VOUT. NOTE 4: in order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2mA is required. TYPICAL CHARACTERISTICS Figure 5: Output Voltage vs Temperature Figure 6: Reference Voltage vs Temperature 11/21 LD29080 SERIES Figure 7: Dropout Voltage vs Temperature Figure 10: Quiescent Current vs Temperature Figure 8: Dropout Voltage vs Output Current Figure 11: Quiescent Current vs Supply Voltage Figure 9: Quiescent Current vs Output Current Figure 12: Quiescent Current vs Temperature 12/21 LD29080 SERIES Figure 13: Short Circuit Current vs Temperature Figure 16: Output Voltage vs Input Voltage Figure 14: Adjust Pin Current vs Temperature Figure 17: Stability vs COUT Figure 15: Supply Voltage Rejection vs Temperature Figure 18: Line Transient VI=3.5 to 13V, IO=10mA, VO=1.5V 13/21 LD29080 SERIES Figure 19: Load Transient VI=3.5V, V O=1.5V, I O=10mA to 0.8A 14/21 LD29080 SERIES SOT-223 MECHANICAL DATA mm. mils DIM. MIN. TYP A MAX. MIN. TYP. 1.8 A1 0.02 B 0.6 B1 MAX. 70.9 0.1 0.8 3.9 0.7 0.85 23.6 27.6 33.5 2.9 3 3.15 114.2 118.1 124.0 c 0.24 0.26 0.35 9.4 10.2 13.8 D 6.3 6.5 6.7 248.0 255.9 263.8 e 2.3 90.6 e1 4.6 181.1 E 3.3 3.5 3.7 129.9 137.8 145.7 H 6.7 7 7.3 129.9 137.8 145.7 V 10˚ 10˚ 0046067/H 15/21 LD29080 SERIES DPAK MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 2.2 2.4 0.086 0.094 A1 0.9 1.1 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.64 0.9 0.025 0.035 B2 5.2 5.4 0.204 0.212 C 0.45 0.6 0.017 0.023 C2 0.48 0.6 0.019 0.023 D 6 6.2 0.236 D1 E 5.1 6.4 E1 6.6 0.252 4.7 e 0.244 0.200 0.260 0.185 2.28 0.090 e1 4.4 4.6 0.173 0.181 H 9.35 10.1 0.368 0.397 L 1 (L1) L2 L4 0.039 2.8 0.110 0.8 0.6 0.031 1 0.023 0.039 0068772-F 16/21 LD29080 SERIES PPAK MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 2.2 2.4 0.086 0.094 A1 0.9 1.1 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.4 0.6 0.015 0.023 B2 5.2 5.4 0.204 0.212 C 0.45 0.6 0.017 0.023 C2 0.48 0.6 0.019 0.023 D 6 6.2 0.236 D1 E 5.1 6.4 0.244 0.201 6.6 0.252 0.260 E1 4.7 0.185 e 1.27 0.050 G 4.9 G1 2.38 2.7 0.093 0.106 H 9.35 10.1 0.368 0.397 L2 0.8 L4 0.6 L5 1 L6 5.25 1 1 2.8 0.193 0.206 0.031 0.023 0.039 0.039 0.039 0.110 0078180-E 17/21 LD29080 SERIES Tape & Reel SOT223 MECHANICAL DATA mm. inch DIM. MIN. TYP A MIN. TYP. 330 13.0 13.2 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 18/21 MAX. 0.504 0.512 14.4 0.519 0.567 Ao 6.73 6.83 6.93 0.265 0.269 0.273 Bo 7.32 7.42 7.52 0.288 0.292 0.296 Ko 1.78 2 0.070 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 7.9 8.0 8.1 0.311 0.315 0.319 0.078 LD29080 SERIES Tape & Reel DPAK-PPAK MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. 330 13.0 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 MAX. 0.504 0.512 22.4 0.519 0.882 Ao 6.80 6.90 7.00 0.268 0.272 0.2.76 Bo 10.40 10.50 10.60 0.409 0.413 0.417 Ko 2.55 2.65 2.75 0.100 0.104 0.105 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 7.9 8.0 8.1 0.311 0.315 0.319 19/21 LD29080 SERIES Table 13: Revision History Date Revision 15-Oct-2004 1 20/21 Description of Changes First Release. LD29080 SERIES Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 21/21