HANBit HDD64M72D18RPW DDR SDRAM Module 512Mbyte (64Mx72bit), based on 32Mx8, 4Banks, 8K Ref., 184Pin-DIMM with PLL & Register Part No. HDD64M72D18RPW GENERAL DESCRIPTION The HDD64M72D18RPW is a 64M x 72 bit Double Data Rate(DDR) Synchronous Dynamic RAM high-density memory module. The module consists of eighteen CMOS 32M x 8 bit with 4banks DDR SDRAMs in 66pin TSOP-II 400mil packages and 2K EEPROM in 8-pin TSSOP package on a 184-pin glass-epoxy. Four 0.1uF decoupling capacitors are mounted on the printed circuit board in parallel for each DDR SDRAM. The HDD64M72D18RPW is a DIMM( Dual in line Memory Module) .Synchronous design allows precise cycle control with the use of system clock. Data I/O transactions are possible on both edges of DQS. Range of operating frequencies, programmable latencies and burst lengths allows the same device to be useful for a variety of high bandwidth, high performance memory system applications. All module components may be powered from a single 2.5V DC power supply and all inputs and outputs are SSTL_2 compatible. FEATURES • Part Identification HDD64M72D18RPW – 10A : 100MHz (CL=2) HDD64M72D18RPW – 13A : 133MHz (CL=2) HDD64M72D18RPW – 13B : 133MHz (CL=2.5) • 512MB(64Mx72) Registered DDR DIMM based on 32Mx8 DDR SDRAM • 2.5V ± 0.2V VDD and VDDQ power supply • Auto & self refresh capability (8K Cycles / 64ms) • All input and output are compatible with SSTL_2 interface • Data(DQ), Data strobes and write masks latched on the rising and falling edges of the clock • All Addresses and control inputs except Data(DQ), Data strobes and Data masks latched on the rising edges of the clock • MRS cycle with address key programs - Latency (Access from column address) : 2, 2.5 - Burst length : 2, 4, 8 - Data scramble : Sequential & Interleave • Data(DQ), Data strobes and write masks latched on the rising and falling edges of the clock • All Addresses and control inputs except Data(DQ), Data strobes and Data masks latched on the rising edges of the clock • The used device is 8M x 8bit x 4Banks DDR SDRAM URL : www.hbe.co.kr REV 1.0 (August.2002) 1 HANBit Electronics Co.,Ltd. HANBit HDD64M72D18RPW PIN ASSIGNMENT PIN Front PIN Back PIN Frontl 1 VREF 2 DQ0 32 A5 62 VDDQ 33 DQ24 63 /WE 3 VSS 34 VSS 64 DQ41 PIN Back PIN Front PIN Back 93 VSS 124 VSS 154 /RAS 94 DQ4 125 A6 155 DQ45 95 DQ5 126 DQ28 156 VDDQ 4 DQ1 35 DQ25 65 /CAS 96 VDDQ 127 DQ29 157 /CS0 5 DQS0 36 DQS3 66 VSS 97 DM0 128 VDDQ 158 /CS1 6 DQ2 37 A4 67 DQS5 98 129 DM3 159 DM5 7 VDD 38 VDD 68 DQ42 99 DQ7 130 A3 160 VSS 8 DQ3 39 DQ26 69 DQ43 100 VSS 131 DQ30 161 DQ46 9 NC 40 DQ27 70 VDD 101 NC 132 VSS 162 DQ47 10 /RESET 41 A2 71 * /CS2 102 NC 133 DQ31 163 * /CS3 11 VSS 42 VSS 72 DQ48 103 *A13 134 CB4 164 VDDQ 12 DQ8 43 A1 73 DQ49 104 VDDQ 135 CB5 165 DQ52 13 DQ9 44 CB0 74 VSS 105 DQ12 136 VDDQ 166 DQ53 14 DQS1 45 CB1 75 * CK2 106 DQ13 137 CK0 167 NC 15 VDDQ 46 VDD 76 * /CK2 107 DM1 138 /CK0 168 VDD DQ6 16 * CK1 47 DQS8 77 VDDQ 108 VDD 139 VSS 169 DM6 17 * /CK1 48 A0 78 DQS6 109 DQ14 140 DM8 170 DQ54 18 VSS 49 CB2 79 DQ50 110 DQ15 141 A10 171 DQ55 19 DQ10 50 VSS 80 DQ51 111 CKE1 142 CB6 172 VDDQ 20 DQ11 51 CB3 81 VSS 112 VDDQ 143 VDDQ 173 NC 21 CKE0 52 BA1 82 VDDID 113 * BA2 144 CB7 174 DQ60 22 VDDQ 83 DQ56 114 DQ20 175 DQ61 23 DQ16 53 DQ32 84 DQ57 115 A12 145 VSS 176 VSS 24 DQ17 54 VDDQ 85 VDD 116 VSS 146 DQ36 177 DM7 25 DQS2 55 DQ33 86 DQS7 117 DQ21 147 DQ37 178 DQ62 26 VSS 56 DQS4 87 DQ58 118 A11 148 VDD 179 DQ63 27 A9 57 DQ34 88 DQ59 119 DM2 149 DM4 180 VDDQ 28 DQ18 58 VSS 89 VSS 120 VDD 150 DQ38 181 SA0 KEY KEY 29 A7 59 BA0 90 NC 121 DQ22 151 DQ39 182 SA1 30 VDDQ 60 DQ35 91 SDA 122 A8 152 VSS 183 SA2 31 DQ19 61 DQ40 92 SCL 123 DQ23 153 DQ44 184 VDDSPD *These pins should be NC in the system which does not support SPD PIN PIN DESCRIPTION PIN PIN DESCRIPTION A0~A12 Address input VDD Power supply(2.5V) BA0~BA1 Bank Select Address VDDQ Power supply for DQs(2.5V) DQ0~DQ63 Data input/output VREF Power supply for reference Serial EEPROM Power supply(3.3) CB0~CB7 Check Bit VDDSPD DQS0~DQS8 Data Strobe input/output VSS Ground DM0~DM8 Data-in Mask SA0~SA2 Address in EEPROM CK0~/CK0 Clock input SDA Serial data I/O CKE0~CKE1 Clock enable input SCL Serial clock /CS0~/CS1 Chip Select input VDDID VDD identification flag /RAS Row Address strobe NC No connection /CAS Column Address strobe URL : www.hbe.co.kr REV 1.0 (August.2002) 2 HANBit Electronics Co.,Ltd. HANBit HDD64M72D18RPW FUNCTIONAL BLOCK DIAGRAM /RCS1 /RCS0 Notes: /RCS0 /RCS1 URL : www.hbe.co.kr REV 1.0 (August.2002) 1. DQ-to-I/O wiring may be changed within a byte. 2. DQ/DQS/DM/CKE/S relationships must be maintained as shown. 3. DQ/DQS resistors should be 22 Ohms. 4. VDDID strap connections (for memory device VDD, VDDQ): STRAP OUT (OPEN): VDD = VDDQ STRAP IN (VSS): VDD ≠ VDDQ. 5. RS0 and RS1 alternate between the back and front sides of the DIMM. 6.Address and control resistors should be 22 Ohms. 3 HANBit Electronics Co.,Ltd. HANBit HDD64M72D18RPW PIN FUNCTION DESCRIPTION Pin CK, /CK Name Clock Input Function CK and CK are differential clock inputs. All address and control input signals are sam-pled on the positive edge of CK and negative edge of CK. Output (read) data is referenced to both edges of CK. Internal clock signals are derived from CK/CK. CKE HIGH activates, and CKE LOW deactivates internal clock signals, and device input buffers and output drivers. Deactivating the clock provides PRECHARGE POWER-DOWN and SELF REFRESH operation (all banks idle), or ACTIVE POWER-DOWN(row ACTIVE in any bank). CKE is synchronous for all functions CKE Clock Enable except for disabling outputs, which is achieved asynchronously. Input buffers, excluding CK, CK and CKE are disabled during power-down and self refresh modes, providing low standby power. CKE will recognizean LVCMOS LOW level prior to VREF being stable on power-up. CS enables(registered LOW) and disables(registered HIGH) the command decoder. /CS Chip Select All commands are masked when CS is registered HIGH. CS provides for external bank selection on systems with multiple banks. CS is considered part of the command code. Row/column addresses are multiplexed on the same pins. A0 ~ A12 Address BA0 ~ BA1 Bank select address Row address : RA0 ~ RA12, Column address : CA0 ~ CA9 BA0 and BA1 define to which bank an ACTIVE, READ, WRITE or PRE-CHARGE command is being applied. Latches row addresses on the positive going edge of the CLK with /RAS low. /RAS Row address strobe /CAS Column address strobe /WE Write enable DQS0~8 Data Strobe Enables row access & precharge. Latches column addresses on the positive going edge of the CLK with /CAS low. Enables column access. Enables write operation and row precharge. Latches data in starting from /CAS, /WE active. Output with read data, input with write data. Edge-aligned with read data, centered in write data. Used to capture write data. DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH along with that input data during a WRITE access. DM is sampled DM0~8 Input Data Mask on both edges of DQS. DM pins include dummy loading internally, to matches the DQ and DQS load-ing. DQ0 ~ 63 Data input/output Data inputs/outputs are multiplexed on the same pins. CB0~CB7 Check Bit Check Bit Input/Output pins VDDQ Supply DQ Power Supply : +2.5V ± 0.2V. VDD Supply Power Supply : +2.5V ± 0.2V (device specific). VSS Supply DQ Ground. VREF Supply SSTL_2 reference voltage. VDDSPD Supply Serial EEPROM Power Supply : 3.3v VDDID URL : www.hbe.co.kr REV 1.0 (August.2002) VDD identification Flag 4 HANBit Electronics Co.,Ltd. HANBit HDD64M72D18RPW ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATING UNTE VIN, VOUT -0.5 ~ 3.6 V Voltage on VDD supply relative to Vss VDD -1.0 ~ 3.6 V Voltage on VDDQ supply relative to Vss VDDQ -0.5 ~ 3.6 V Storage temperature TSTG -55 ~ +150 °C PD 18 W Voltage on any pin relative to Vss Power dissipation Short circuit current IOS 50 Notes: Operation at above absolute maximum rating can adversely affect device reliability mA DC OPERATING CONDITIONS (Recommended operating conditions (Voltage referenced to Vss = 0V, TA = 0 to 70°C) ) PARAMETER Supply Voltage I/O Supply Voltage I/O Reference Voltage SYMBOL MIN MAX UNIT NOTE VDD 2.3 2.7 V VDDQ 2.3 2.7 V VREF VDDQ/2 - 50mA VDDQ/2 + V 1 50mA VTT VREF – 0.04 VREF + 0.04 V 2 Input High Voltage VIH (DC) VREF + 0.15 VREF + 0.3 V 4 Input Low Voltage VIL (DC) -0.3 VREF - 0.15 V 4 Input Voltage Level, CK and /CK inputs VIN (DC) -0.3 VDDQ + 0.3 V Input Differential Voltage, CK and /CK inputs VID (DC) 0.3 VDDQ + 0.6 V 3 Input crossing point Voltage, CK and /CK VIX (DC) 1.15 1.35 V 5 Input leakage current I LI -2 2 uA Output leakage current I OZ -5 5 uA Output High current (VOUT = 1.95V) I OH -16.8 mA Output Low current (VOUT = 0.35V) I OL 16.8 mA I/O Termination Voltage(system) inputs Notes : 1. Includes ± 25mV margin for DC offset on VREF, and a combined total of ± 50mV margin for all AC noise and DC offset on VREF, bandwidth limited to 20MHz. The DRAM must accommodate DRAM current spikes on VREF and internal DRAM noise coupled to VREF , both of which may result in VREF noise. VREF should be de-coupled with an inductance of ≤ 3nH. 2. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF, and must track variations in the DC level of VREF 3. VID is the magnitude of the difference between the input level on CK and the input level on CK. 4. These parameters should be tested at the pin on actual components and may be checked at either the pin or the pad in simulation. The AC and DC input specifications are relative to a VREF envelop that has been bandwidth limited to 200MHZ. 5. The value of VIX is expected to equal 0.5*VDDQ of the transmitting device and must track variations in the dc level of the same. 6. These charactericteristics obey the SSTL-2 class II standards. URL : www.hbe.co.kr REV 1.0 (August.2002) 5 HANBit Electronics Co.,Ltd. HANBit CAPACITANCE HDD64M72D18RPW (VDD = min to max, VDDQ = 2.5V to 2.7V, TA = 25°C, f = 100MHz) DESCRIPTION SYMBOL MIN MAX UNITS Input capacitance(A0~A12, BA0~BA1, /RAS, /CAS,/WE) CIN1 - 12 pF Input capacitance(CKE0,CKE1) CIN2 - 12 pF Input capacitance(/CS0,/CS1) CIN3 - 11 pF Input capacitance(CK0~/CK1) CIN4 - 12 pF Input capacitance(DM0~DM8) CIN5 - 16 pF 16 pF 16 pF Data & DQS input/output capacitance (DQ0 ~ DQ63, COUT1 - DQS0~DQS8) Data input/output capacitance (CB0~CB7)) COUT2 - DC CHARACTERISTICS (Recommended operating condition unless otherwise noted, VDD = 2.5V, T =25°C) Symbo TEST l Condition Operating current (One bank active-Precharge) IDD0 tRC ≥ tRC(min), tCK=100MHz for DDR200,133MHz for DDR266A & DDR266B DQ,DM and DQS inputs changing twice per clock cycle Address and control inputs changing once per clock cycle Operating current (One bankOperation) IDD1 Precharge powerdown standby current IDD2P pARAMETER Precharge Floating standby current IDD2F Precharge Quiet Standby current IDD2Q version Unit -10A -13A -13B 1515 1695 1695 mA One bank open, BL=4,Reads-Refer to the following page for detailed test condition 1605 1875 1875 mA All banks idle, power-down mode CKE ≤ VIL(max), tCK=100MHz for DDR200,133MHz for DDR266A & DDR266B VIN = VREF for DQ,DQS and DM 885 1020 1020 mA 1020 1155 1155 mA 975 1110 1110 /CS≥ VIH(min), All banks idle CKE ≥ VIH(min), tCK=100MHz for DDR200,133MHz for DDR266A & DDR266B Address and control inputs changing once per clock cycle VIN = VREF for DQ,DQS and DM /CS≥ VIH(min), All banks idle CKE ≥ VIH(min), tCK=100MHz for DDR200,133MHz for DDR266A & DDR266B Address and other control inputs stable with keeping≥ VIH(min) or ≤ VIL(max) VIN = VREF for DQ,DQS and DM Active power-down Mode standby current IDD3P One bank active; power-down mode; CKE ≤ VIL(max), tCK=100MHz for DDR200,133MHz for DDR266A & DDR266B VIN = VREF for DQ,DQS and DM. 1020 1155 1155 mA IDD3N CS# >= VIH(min), CKE>=VIH(min) one bank active, active – precharge, tRC=tRASmax tCK = 100Mhz for DDR200, 133Mhz for DDR266A & DDR266B, DQ, DQS and DM inputs changing twice per clock cycle Address and other control inputs changing once per clock cycle 1110 1290 1290 mA Active standby current URL : www.hbe.co.kr REV 1.0 (August.2002) 6 HANBit Electronics Co.,Ltd. HANBit HDD64M72D18RPW Operating current (burst read) IDD4R BL = 2, reads, continuous burst One bank open, Address and control inputs changing once per clock cycle, IOUT = 0mA 2055 2415 2415 mA Operating current (Bust write) IDD4W BL = 2, write, continuous burst One bank open, Address and control inputs changing once per clock cycle 2415 2955 2955 mA Auto refresh current IDD5 tRC = tRFC(min) - 8*tCK for DDR200 at 100Mhz, 10*tCK for DDR266A & DDR266B at 133Mhz, distributed refresh Self refresh current IDD6 CKE =< 0.2V, External clock should be on tCK = 100Mhz for DDR200, 133Mhz for DDR266A & DDR266B mA 2055 2415 2415 354 354 354 327 327 327 Four bank interleaving with BL=4 -Refer to the following page for detailed test 3315 condition Notes: Operation at above absolute maximum rating can adversely affect device reliability 3945 3945 Normal Low Power Operating current (Four bank operation) IDD7A mA mA AC OPERATING CONDITIONS PARAMETER STMBOL MIN Input High (Logic 1) Voltage, DQ, DQS and DM signals VIH (AC) VREF + 0.31 Input Low (Logic 0) Voltage, DQ, DQS and DM signals. VIL (AC) Input Differential Voltage, CK and CK inputs VID (AC) Input Crossing Point Voltage, CK and CK inputs VIX (AC) MAX UNIT NOTE 3 VREF - 0.31 V 3 0.7 VDDQ+0.6 V 1 0.5*VDDQ-0.2 0.5*VDDQ+0.2 V 2 Notes: 1. VID is the magnitude of the difference between the input level on CK and the input on CK. 2. The value of VIX is expected to equal 0.5* VDDQ of the transmitting device and must track variations in the DC level of the same 3. These parameters should be tested at the pim on actual components and may be checked at either the pin or the pad in simula-tion. the AC and DC input specificatims are refation to a Vref envelope that has been bandwidth limited 20MHz. AC OPERATING TEST CONDITIONS PARAMETER VALUE UNIT Input reference voltage for Clock 0.5 * VDDQ V Input signal maximum peak swing 1.5 V Input signal minimum slew rate 1.0 V VREF+0.35/VREF V Input timing measurement reference level VREF V Output timing measurement reference level VTT V See Load Circuit V Input Levels(VIH/VIL) Output load condition URL : www.hbe.co.kr REV 1.0 (August.2002) 7 NOTE HANBit Electronics Co.,Ltd. HANBit HDD64M72D18RPW AC CHARACTERISTICS (These AC charicteristics were tested on the Component) PARAMETER DDR200 DDR266A DDR266B -10A -13A -13B SYMBOL MIN MAX MIN MAX MIN UNIT NOTE MAX Row cycle time tRC 70 65 65 ns 1 Refresh row cycle time tRFC 80 75 75 ns 1,2 Row active time tRAS 48 ns 1,2 /RAS to /CAS delay tRCD 20 20 20 ns 3 Row precharge time tRP 20 20 20 ns 3 Row active to Row active delay tRRD 15 15 15 ns 3 Write recovery time tWR 2 2 2 tCK 3 Last data in to Read command tCDLR 1 1 1 tCK 2 Col. address to Col. address delay tCCD 1 1 1 tCK CL=2.0 Clock cycle time 120K 10 45 120K 45 120K 12 7.5 12 10 12 ns 12 7.5 12 7.5 12 ns tCK CL=2.5 Clock high level width tCH 0.45 0.55 0.45 0.55 0.45 0.55 tCK Clock low level width tCL 0.45 0.55 0.45 0.55 0.45 0.55 tCK tDQSCK -0.8 +0.8 -0.75 +0.75 -0.75 +0.75 ns Output data access time from CK/CK tAC -0.8 +0.8 -0.75 +0.75 -0.75 +0.75 ns Data strobe edge to ouput data edge tDQSQ - +0.6 - +0.5 - +0.5 ns Read Preamble tRPRE 0.9 1.1 0.9 1.1 0.9 1.1 tCK Read Postamble tRPST 0.4 0.6 0.4 0.6 0.4 0.6 tCK DQS-out access time from CK/CK URL : www.hbe.co.kr REV 1.0 (August.2002) 8 HANBit Electronics Co.,Ltd. HANBit HDD64M72D18RPW Data out high impedence time from tHZQ -0.8 +0.8 -0.75 +0.75 -0.75 +0.75 ns CK to valid DQS-in tDQSS 0.75 1.25 0.75 1.25 0.75 1.25 tCK DQS-in setup time tWPRES 0 0 0 ns DQS-in hold time tWPREH 0.25 0.25 0.25 tCK tDSS 0.2 0.2 0.2 tCK tDSH 0.2 0.2 0.2 tCK DQS-in high level width tDQSH 0.35 0.35 0.35 tCK DQS-in low level width tDQSL 0.35 0.35 0.35 tCK DQS-in cycle time tDSC 0.9 Address and Control Input setup time tIS 1.1 0.9 0.9 ns Address and Control Input hold time tIH 1.1 0.9 0.9 ns Mode register set cycle time tMRD 16 15 15 ns DQ & DM setup time to DQS tDS 0.6 0.5 0.5 ns DQ & DM hold time to DQS tDH 0.6 0.5 0.5 ns DQ & DM input pulse width tDIPW 2 1.75 1.75 ns Power down exit time tPDEX 10 10 10 ns Exit self refresh to write command tXSW 116 95 tXSA 80 Exit self refresh to read command tXSR 200 200 200 Cycle Refresh interval time TREF 7.8 7.8 7.8 us Output DQS valid window TQH 0.35 0.35 0.35 tCK DQS write postamble time TWPST 0.25 0.25 0.25 tCK 2 CK-/CK 3 DQS-in falling edge to CK rising-setup time DQS-in falling edge to CK rising hold time 1.1 Exit self refresh to bank active 0.9 1.1 75 0.9 1.1 tCK ns 75 ns command Notes : 1. 2. Maximum burst refresh of 8. tHZQ transitions occurs in the same assess time windows as valid data transitions. These parameters are not referenced to a specific voltage level, but specify when the device output is no longer driving. 3. The specific requirement is that DQS be valid(High-Low) on or before this CK edge. The case shown(DQS going from High_Z to logic Low) applies when no writes were previously in progress on the bus. If a previous write was in progress, DQS could be High at this time, depending on tDQSS. 4. The maximum limit for this parameter is not a device limit. The device will operate with a great value for this parameter, but system performance (bus turnaround) will degrade accordingly. URL : www.hbe.co.kr REV 1.0 (August.2002) 9 HANBit Electronics Co.,Ltd. 1 4 HANBit HDD64M72D18RPW SIMPLIFIED TRUTH TABLE COMMAND CK E n-1 CK E n /CS /R A S /C A S /WE DM BA 0,1 A10/ AP A11,A12 A9~A0 NOTE Register Extended MRS H X L L L L X OP code 1,2 Register Mode register set H X L L L L X OP code 1,2 L L L H X X L H H H H X X X Auto refresh Refresh Self refresh Entry Exit Bank active & row addr. Read & Auto column disable address Auto precharge eable Write & column address H H L L H H X L L H H X V H X L H L H X V disable Auto precharge H H X L H L Precharg Bank selection e All banks active power down Precharge power down mode H X L H H L X H X L L H L X H X X X L V V V X X X X Entry H L Exit L H Entry H L Exit L H DM H No operation command H H X X X L H H H H X X X V V V L X X H X X X L H H H X 3 Row address Column L Address 4 H (A0 ~A9) 4 L Column 4 H (A0 ~ A9) V L enable Burst Stop X 3 3 X precharge Auto precharge Clock suspend or X 3 Address X V L X H 4,6 7 X 5 X X X X X V X X X 8 (V=Valid, X=Don't care, H=Logic high, L=Logic low) Notes : 1. OP Code : Operand code A0 ~ A12 & BA0 ~ BA1 : Program keys. (@ MRS) 2. MRS can be issued only at all banks precharge state. A new command can be issued after 2 CLK cycles of MRS. 3. Auto refresh functions are as same as CBR refresh of DRAM. The automatical precharge without row precharge command is meant by "Auto". Auto/self refresh can be issued only at all banks precharge state. 4. BA0 ~ BA1 : Bank select addresses. If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected. If both BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank B is selected. If both BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank C is selected. If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected. If A10/AP is "High" at row precharge, BA0 and BA1 is ignored and all banks are selected. 5. During burst read or write with auto precharge, new read/write command can not be issued. Another bank read/write command can be issued after the end of burst. New row active of the associated bank can be issued at tRP after the end of burst. 6. Burst stop command is valid at every burst length. 7. DM sampled at the rising and falling edges of the DQS and Data-in are masked at the both edges (Write DM latency is 0) URL : www.hbe.co.kr REV 1.0 (August.2002) 10 HANBit Electronics Co.,Ltd. HANBit HDD64M72D18RPW PACKAGING INFORMATION Unit : mm <Front– Side > 133.35 ± 0.20 U11 U1 U2 U3 U5 U4 U6 U7 U8 U9 30.48± 0.20 U12 A B < Rear – Side > 133.35 ± 0.20 U13 U22 U21 U20 U19 U18 U1 U17 U16 U15 U14 30.48± 0.20 0 *** PCB 두 께 : 1.27 ± 0.08 mm URL : www.hbe.co.kr REV 1.0 (August.2002) 11 HANBit Electronics Co.,Ltd. HANBit HDD64M72D18RPW ORDERING INFORMATION Part Number Density Org. Package Ref. Vcc 8K 2.5V 8K 2.5V 8K 2.5V Low Profile HDD64M72D18RWP-10A 512MByte 64M x 72 184PIN DIMM Low Profile HDD64M72D18RW-13A 512MByte 64M x 72 184PIN DIMM Low Profile HDD64M72D18RW-13B 512MByte 64M x 72 184PIN DIMM URL : www.hbe.co.kr REV 1.0 (August.2002) 12 MODE Registered DDR Registered DDR MAX.frq 100MHz/CL2 133MHz/CL2 Registered 133MHz/CL2 DDR .5 HANBit Electronics Co.,Ltd.