NCV8504 Series
Micropower 400 mA LDO
Linear Regulators with
DELAY, Adjustable RESET,
and General Use Comparator
The NCV8504 is a family of precision micropower voltage
regulators. Their output current capability is 400 mA. The family has
output voltage options for Adjustable, 2.5 V, 3.3 V and 5.0 V.
The output voltage is accurate within ± 2.0% with a maximum
dropout voltage of 0.6 V at 400 mA. Low quiescent current is a feature
drawing only 100 μA with a 100 μA load. This part is ideal for any and
all battery operated microprocessor equipment.
Microprocessor control logic includes an active RESET (with
DELAY).
The active RESET circuit operates correctly at an output voltage as
low as 1.0 V. The RESET function is activated during the power up
sequence or during normal operation if the output voltage drops below
the regulation limits.
The reset threshold voltage can be decreased by the connection of
external resistor divider to RADJ lead.
The general use comparator (FLAG/Monitor) is referenced to a
temperature stable voltage and provides 1 mA of drive current at its
open collector output.
The regulator is protected against reverse battery, short circuit, and
thermal overload conditions. The device can withstand load dump
transients making it suitable for use in automotive environments. The
device has also been optimized for EMC conditions.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
Output Voltage Options: Adjustable, 2.5 V, 3.3 V, 5.0 V
± 2.0% Output
Low 100 μA Quiescent Current
Fixed or Adjustable Output Voltage
Active RESET
Adjustable Reset
400 mA Output Current Capability
Fault Protection
♦ +60 V Peak Transient Voltage
♦ −15 V Reverse Voltage
♦ Short Circuit
♦ Thermal Overload
General Use Comparator
NCV Prefix for Automotive and Other Applications Requiring Site
and Change Control
AEC Qualified
PPAP Capable
These are Pb−Free Devices
© Semiconductor Components Industries, LLC, 2010
May, 2010 − Rev. 22
1
http://onsemi.com
MARKING
DIAGRAM
16
1
SOIC 16 LEAD
WIDE BODY
EXPOSED PAD
PDW SUFFIX
CASE 751AG
16
NCV8504x
AWLYYWWG
1
x
= Voltage Ratings as Indicated Below:
A = Adjustable
2 = 2.5 V
3 = 3.3 V
5 = 5.0 V
A
= Assembly Location
WL = Wafer Lot
YY = Year
WW = Work Week
G = Pb−Free Device
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
Publication Order Number:
NCV8504/D
NCV8504 Series
PIN CONNECTIONS
ADJUSTABLE OUTPUT
1
VADJ
VOUT
NC
NC
NC
NC
VIN
MON
FIXED OUTPUT
16
FLAG
RESET
NC
GND
NC
NC
DELAY
RADJ
SENSE
VOUT
NC
NC
NC
NC
VIN
MON
1
16
FLAG
RESET
NC
GND
NC
NC
DELAY
RADJ
Monitor
IQ
VIN
VOUT
(VO)
VDD
33 μF
10 μF
RADJ
NCV8504
DELAY
RFLG
5.1 k
Microprocessor
VBAT
SENSE
(Fixed Output Only)
RRST
5.1 k
MON
CDELAY
VADJ
(Adjustable
Output Only)
FLAG
RESET
I/O
GND
Figure 1. Application Diagram
http://onsemi.com
2
I/O
NCV8504 Series
MAXIMUM RATINGS*{
Rating
Value
Unit
−15 to 45
V
Peak Transient Voltage (46 V Load Dump @ VIN = 14 V)
60
V
Operating Voltage
45
V
VOUT (DC)
−0.3 to 16
V
Voltage Range (RESET, FLAG, RADJ, DELAY)
−0.3 to 10
V
Input Voltage Range
MON
VADJ
−0.3 to 10
−0.3 to 16
V
V
4.0
200
kV
V
Junction Temperature, TJ
−40 to +150
°C
Storage Temperature, TS
−55 to 150
°C
16
57
°C/W
°C/W
260 peak (Note 2)
°C
VIN (DC)
ESD Susceptibility
(Human Body Model)
(Machine Model)
Package Thermal Resistance, SOW−16 E PAD:
Junction−to−Case, RθJC
Junction−to−Ambient, RθJA
Lead Temperature Soldering:
Reflow: (SMD styles only) (Note 1)
1. 150 second maximum above 217°C.
2. −5°C/+0°C allowable conditions.
*The maximum package power dissipation must be observed.
†During the voltage range which exceeds the maximum tested voltage of VIN, operation is assured, but not specified. Wider limits may apply.
Thermal dissipation must be observed closely.
ELECTRICAL CHARACTERISTICS (IOUT = 1.0 mA, −40°C ≤ TJ ≤ 150°C; VIN = dependent on voltage option (Note 3);
unless otherwise specified.)
Test Conditions
Characteristic
Min
Typ
Max
Unit
Output Stage
Output Voltage for 2.5 V Option
(VO)
6.5 V < VIN < 16 V, 1.0 mA ≤ IOUT ≤ 400 mA
4.5 V < VIN < 26 V, 1.0 mA ≤ IOUT ≤ 400 mA
2.450
2.425
2.5
2.5
2.550
2.575
V
V
Output Voltage for 3.3 V Option
(VO)
7.3 V < VIN < 16 V, 1.0 mA ≤ IOUT ≤ 400 mA
4.5 V < VIN < 26 V, 1.0 mA ≤ IOUT ≤ 400 mA
3.234
3.201
3.3
3.3
3.366
3.399
V
V
Output Voltage for 5.0 V Option
(VO)
9.0 V < VIN < 16 V, 1.0 mA ≤ IOUT ≤ 400 mA
6.0 V < VIN < 26 V, 1.0 mA ≤ IOUT ≤ 400 mA
4.90
4.85
5.0
5.0
5.10
5.15
V
V
Output Voltage for Adjustable Option
(VO)
VOUT = VADJ (Unity Gain)
6.5 V < VIN < 16 V, 1.0 mA < IOUT < 400 mA
4.5 V < VIN < 26 V, 1.0 mA < IOUT < 400 mA
1.274
1.261
1.300
1.306
1.326
1.339
V
V
Dropout Voltage (VIN − VOUT)
(5.0 V and Adj. > 5.0 V Options Only)
IOUT = 400 mA
IOUT = 1.0 mA
−
−
400
30
600
150
mV
mV
Load Regulation
VIN = 14 V, 5.0 mA ≤ IOUT ≤ 400 mA
−30
5.0
30
mV
Line Regulation (2.5 V, 3.3 V, and
Adjustable Options)
4.5 V < VIN < 26 V, IOUT = 1.0 mA
−
5.0
25
mV
Line Regulation (5.0 V Option)
6.0 V < VIN < 26 V, IOUT = 1.0 mA
−
5.0
25
mV
Quiescent Current, (IQ) Active Mode
IOUT = 100 μA, VIN = 12 V, Delay = 3.0 V, MON = 3.0 V
IOUT = 75 mA, VIN = 14 V, Delay = 3.0 V, MON = 3.0 V
IOUT ≤ 400 mA, VIN = 14 V, Delay = 3.0 V, MON = 3.0 V
−
−
−
100
2.5
25
150
5.0
45
μA
mA
mA
−
425
800
−
mA
Current Limit
Short Circuit Output Current
VOUT = 0 V
100
500
−
mA
Thermal Shutdown
(Guaranteed by Design)
150
180
−
°C
3. Voltage range specified in the Output Stage of the Electrical Characteristics in boldface type.
http://onsemi.com
3
NCV8504 Series
ELECTRICAL CHARACTERISTICS (continued) (IOUT = 1.0 mA, −40°C ≤ TJ ≤ 150°C; VIN = dependent on voltage option (Note 4);
unless otherwise specified.)
Characteristic
Test Conditions
Min
Typ
Max
Unit
2.35
2.30
25
−
−
−
1.0 × VO
−
−
V
V
mV
3.10
3.00
35
−
−
−
1.0 × VO
−
−
V
V
mV
4.70
4.60
50
−
−
−
1.0 × VO
−
−
V
V
mV
1.22
1.19
10
−
−
−
1.0 × VO
−
−
V
V
mV
−
0.1
0.4
V
Reset Function (RESET)
RESET Threshold for 2.5 V Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 4.5 V (Note 5) (Note 6)
VOUT Increasing
VOUT Decreasing
RESET Threshold for 3.3 V Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 4.5 V (Note 5) (Note 6)
VOUT Increasing
VOUT Decreasing
RESET Threshold for 5.0 V Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 6.0 V (Note 6)
VOUT Increasing
VOUT Decreasing
RESET Threshold for Adjustable Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 4.5 V (Note 5) (Note 6)
VOUT Increasing
VOUT Decreasing
RESET Output Voltage
Low (VRLO)
VIN = Minimum (Note 6) (Note 7)
1.0 V ≤ VOUT ≤ VRL, RRESET = 5.1 k
DELAY Switching Threshold (VDT)
(2.5 V, 3.3 V, and 5.0 V Options)
VIN = Minimum (Note 6) (Note 7)
1.4
1.8
2.2
V
DELAY Switching Threshold (VDT)
(Adjustable Option)
VIN = Minimum (Note 6) (Note 7)
1.0
1.3
1.6
V
DELAY Low Voltage
VIN = Minimum (Note 6) (Note 7)
VOUT < RESET Threshold Low(min)
−
−
0.2
V
DELAY Charge Current
VIN = Minimum (Note 6) (Note 7)
DELAY = 1.0 V, VOUT > VRH
2.5
4.0
5.5
μA
DELAY Discharge Current
VIN = Minimum (Note 6) (Note 7)
DELAY = 1.0 V, VOUT < VRL
5.0
−
−
mA
Reset Adjust Switching Voltage (VR(ADJ))
Hysteresis
VIN = Minimum (Note 6) (Note 7)
Increasing and Decreasing
1.16
20
1.25
50
1.34
100
V
mV
Monitor Threshold
Increasing and Decreasing,
VIN = Minimum (Note 6) (Note 7)
1.22
1.29
1.36
V
Hysteresis
VIN = Minimum (Note 6) (Note 7)
10
35
75
mV
Input Current
MON = 2.0 V
−1.0
0.1
1.0
μA
Output Saturation Voltage
MON = 0 V, IFLAG = 1.0 mA,
VIN = Minimum (Note 6) (Note 7)
−
0.1
0.4
V
−0.5
−
0.5
μA
FLAG/Monitor
Voltage Adjust (Adjustable Output only)
Input Current
VADJ = 1.25 V
4. Voltage range specified in the Output Stage of the Electrical Characteristics in boldface type.
5. For VIN ≤ 4.5 V, a RESET = Low may occur with the output in regulation.
6. Part is guaranteed by design to meet specification over the entire VIN voltage range, but is production tested only at the specified VIN
voltage.
7. Minimum VIN = 4.5 V for 2.5 V, 3.3 V, and Adjustable options. Minimum VIN = 6.0 V for 5.0 V option.
http://onsemi.com
4
NCV8504 Series
PACKAGE PIN DESCRIPTION, ADJUSTABLE OUTPUT
Pin Number
Pin Symbol
1
VADJ
Voltage Adjust. A resistor divider from VOUT to this lead sets the output voltage.
2
VOUT
±2.0%, 400 mA output.
3−6, 11, 12, 14
NC
No connection.
7
VIN
Input Voltage.
8
MON
Monitor. Input to comparator. If not needed connect to VOUT.
9
RADJ
Reset Adjust. If not needed connect to ground.
10
DELAY
13
GND
15
RESET
Active reset (accurate to VOUT ≥ 1.0 V)
16
FLAG
Open collector output from comparator.
NOTE:
Function
Timing capacitor for RESET function.
Ground. All GND leads must be connected to Ground.
Tentative pinout for SOW−16 E Pad.
PACKAGE PIN DESCRIPTION, FIXED OUTPUT
Pin Number
Pin Symbol
1
SENSE
2
VOUT
3−6, 11, 12, 14
NC
No connection.
7
VIN
Input Voltage.
8
MON
Monitor. Input to comparator. If not needed connect to VOUT.
9
RADJ
Reset Adjust. If not needed connect to ground.
10
DELAY
13
GND
15
RESET
Active reset (accurate to VOUT ≥ 1.0 V)
16
FLAG
Open collector output from comparator.
NOTE:
Function
Kelvin connection which allows remote sensing of output voltage for improved regulation. If
remote sensing is not desired, connect to VOUT.
±2.0%, 400 mA output.
Timing capacitor for RESET function.
Ground. All GND leads must be connected to Ground.
Tentative pinout for SOW−16 E Pad.
http://onsemi.com
5
NCV8504 Series
VOUT
VIN
Current Source
(Circuit Bias)
SENSE
IBIAS
Current Limit
Sense
RADJ
+
+
−
IBIAS
VBG − 18 mV
RESET
Error Amplifier
VBG
+
Fixed Versions only
−
Thermal
Protection
4.0 μA
DELAY
+ −
1.8 V
(Fixed Versions)
1.3 V
(Adjustable Version)
IBIAS
Bandgap
Reference
VBG
VBG
−
Figure 2. Block Diagram
http://onsemi.com
6
VADJ
GND
IBIAS
+
MON
15 k
Adjustable
Version only
FLAG
NCV8504 Series
TYPICAL PERFORMANCE CHARACTERISTICS
5.10
3.35
Vout, OUTPUT VOLTAGE (V)
5.08
5.06
Vout, OUTPUT VOLTAGE (V)
VOUT = 5.0 V
VIN = 14 V
IOUT = 5.0 mA
5.04
5.02
5.00
4.98
4.96
4.94
VOUT = 3.3 V
VIN = 14 V
IOUT = 5.0 mA
3.33
3.31
3.29
3.27
3.25
4.92
4.90
−40 −20
0
3.23
−40 −20
20 40
60 80 100 120 140 160
TEMPERATURE (°C)
Figure 3. 5 V Output Voltage vs Temperature
600
Vout, OUTPUT VOLTAGE (V)
2.54
DROPOUT VOLTAGE (mV)
VOUT = 2.5 V
VIN = 14 V
IOUT = 5.0 mA
2.53
2.52
2.51
2.50
2.49
2.48
2.47
500
125 °C
400
25 °C
300
200
−40 °C
100
2.46
5 V and Adj. > 5 V options only
2.45
−40 −20
0
0
20 40
60 80 100 120 140 160
TEMPERATURE (°C)
0
Figure 5. 2.5 V Output Voltage vs Temperature
100
Unstable Region
10
Stable Region
CVOUT = 0.1 mF
1.0
Stable Region
Unstable Region
VIN = 14 V
CVOUT = 10 mF
50
400
CVOUT = 33 mF*
ESR (W)
1.0
350
Unstable Region
2.5 V
0.1
300
100 150
200
250
Iout, OUTPUT CURRENT (mA)
100
3.3 V
10
ESR (W)
50
Figure 6. Dropout Voltage vs Output Current
5.0 V
0
20 40
60 80 100 120 140 160
TEMPERATURE (°C)
Figure 4. 3.3 V Output Voltage vs Temperature
2.55
0.01
0
300
100 150 200
250
Iout, OUTPUT CURRENT (mA)
350
0.1
400
*There is no unstable lower
region for the 33 mF capacitor
0
Figure 7. Output Stability with
Output Voltage Change
50
Figure 8. Output Stability with
Output Capacitor Change
http://onsemi.com
7
5 V version
300
100 150 200
250
Iout, OUTPUT CURRENT (mA)
350
400
NCV8504 Series
TYPICAL PERFORMANCE CHARACTERISTICS
1.8
+25°C
60
+125°C
1.6
IQ, QUIESCENT CURRENT (mA)
IQ, QUIESCENT CURRENT (mA)
2.0
−40°C
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0
5
10
40
15 20
25 30 35
IOUT, OUTPUT CURRENT (mA)
45
+25°C
40
−40°C
30
20
10
0
50
+125°C
50
Figure 9. Quiescent Current vs Output Current
Iout = 200 mA
140
T = 25°C
10
8
6
Iout = 100 mA
4
Iout = 50 mA
2
Iout = 10 mA
0
6
8
10
12 14
16 18 20
VIN, INPUT VOLTAGE (V)
22
24
100 150 200 250 300 350 400 450 500
IOUT, OUTPUT CURRENT (mA)
Figure 10. Quiescent Current vs Output Current
IQ, QUIESCENT CURRENT (mA)
IQ, QUIESCENT CURRENT (mA)
12
50
0
Iout = 100 mA
100
80
60
40
20
0
26
T = 25°C
120
8
6
10
12 14
16 18 20
VIN, INPUT VOLTAGE (V)
22
24
26
Figure 12. Quiescent Current vs Input Voltage
Figure 11. Quiescent Current vs Input Voltage
http://onsemi.com
8
NCV8504 Series
CIRCUIT DESCRIPTION
REGULATOR CONTROL FUNCTIONS
The NCV8504 contains the microprocessor compatible
control function RESET (Figure 13).
The DELAY lead provides source current (typically 4.0 μA)
to the external DELAY capacitor during the following
proceedings:
1. During Power Up (once the regulation threshold
has been verified).
2. After a reset event has occurred and the device is
back in regulation. The DELAY capacitor is
discharged when the regulation (RESET threshold)
has been violated. This is a latched incident. The
capacitor will fully discharge and wait for the
device to regulate before going through the delay
time event again.
VIN
RESET
Threshold
VOUT
DELAY
Threshold
(VDT)
DELAY
RESET
FLAG/Monitor Comparator
Td
Td
A general use comparator is included whose positive input
terminal is tied to the on−chip bandgap voltage reference.
This provides a very temperature stable referenced
comparator with versatile use in any system. The trip point
can be programmed externally using a resistor divider to the
input monitor (MON) (Figure 15). The typical threshold is
1.29 V on the MON pin.
Figure 13. Reset and Delay Circuit Wave Forms
RESET Function
A RESET signal (low voltage) is generated as the IC
powers up until VOUT is within 1.5% of the regulated output
voltage, or when VOUT drops out of regulation,and is lower
than 4.0% below the regulated output voltage. Hysteresis is
included in the function to minimize oscillations.
The RESET output is an open collector NPN transistor,
controlled by a low voltage detection circuit. The circuit is
functionally independent of the rest of the IC thereby
guaranteeing that the RESET signal is valid for VOUT as low
as 1.0 V.
VMON
VBAT
The reset threshold can be made lower by connecting an
external resistor divider to the RADJ lead from the VOUT
lead, as displayed in Figure 14. This lead is grounded to
select the default value of 4.6 V (on the 5.0 V option).
NCV8504
DELAY
RRST
RESET
MON
FLAG
RADJ
RESET
DELAY
GND
μP
COUT
I/O
RESET
Figure 15. Flag/Monitor Function
to μP and
System
Power
VOUT
RADJ
VCC
NCV8504
Adjustable Reset Function
VR(ADJ)
VOUT
VIN
Voltage Adjust
Figure 16 shows the device setup for a user configurable
output voltage. The feedback to the VADJ pin is taken from
a voltage divider referenced to the output voltage. The loop
is balanced around the Unity Gain threshold (1.30 V
typical).
COUT
to μP and
RESET
Port
≈5.0 V
VOUT
NCV8504
CDELAY
VADJ
15 k
1.28 V
5.1 k
Figure 14. Adjustable RESET
DELAY Function
The reset delay circuit provides a programmable (by
external capacitor) delay on the RESET output lead.
Figure 16. Adjustable Output
Voltage
http://onsemi.com
9
COUT
NCV8504 Series
APPLICATION NOTES
FLAG MONITOR
Figure 17 shows the FLAG Monitor waveforms as a result
of the circuit depicted in Figure 15. As the input voltage falls
(VMON), the Monitor threshold is crossed. This causes the
voltage on the FLAG output to go low.
VIN
VOUT
CIN*
0.1 μF
NCV8504
COUT**
33 μF
RRST
RESET
VMON
*CIN required if regulator is located far from the power supply filter
**COUT required for stability. Capacitor must operate at minimum
temperature expected
MON
Figure 18. Test and Application Circuit Showing
Output Compensation
Flag Monitor
Ref. Voltage
CALCULATING POWER DISSIPATION IN A
SINGLE OUTPUT LINEAR REGULATOR
The maximum power dissipation for a single output
regulator (Figure 19) is:
FLAG
PD(max) + [VIN(max) * VOUT(min)] IOUT(max)
Figure 17. FLAG Monitor Circuit Waveform
where:
VIN(max) is the maximum input voltage,
VOUT(min) is the minimum output voltage,
IOUT(max) is the maximum output current for the
application, and
IQ is the quiescent current the regulator consumes at
IOUT(max).
Once the value of PD(max) is known, the maximum
permissible value of RqJA can be calculated:
SETTING THE DELAY TIME
The delay time is controlled by the Reset Delay Low
Voltage, Delay Switching Threshold, and the Delay Charge
Current. The delay follows the equation:
tDELAY +
ƪCDELAY(Vdt * Reset Delay Low Voltage)ƫ
Delay Charge Current
Example:
Using CDELAY = 33 nF.
Assume reset Delay Low Voltage = 0.
Use the typical value for Vdt = 1.8 V (2.5 V, 3.3 V, and
5.0 V options).
Use the typical value for Delay Charge Current = 4.2 μA.
tDELAY +
ƪ33 nF(1.8 * 0)ƫ
4.2 mA
(1)
) VIN(max)IQ
o
T
RqJA + 150 C * A
PD
(2)
The value of RqJA can then be compared with those in the
package section of the data sheet. Those packages with
RqJA’s less than the calculated value in equation 2 will keep
the die temperature below 150°C.
In some cases, none of the packages will be sufficient to
dissipate the heat generated by the IC, and an external
heatsink will be required.
+ 14 ms
STABILITY CONSIDERATIONS
The output or compensation capacitor helps determine
three main characteristics of a linear regulator: start−up
delay, load transient response and loop stability.
The capacitor value and type should be based on cost,
availability, size and temperature constraints. A tantalum or
aluminum electrolytic capacitor is best, since a film or
ceramic capacitor with almost zero ESR can cause
instability. The aluminum electrolytic capacitor is the least
expensive solution, but, if the circuit operates at low
temperatures (−25°C to −40°C), both the value and ESR of
the capacitor will vary considerably. The capacitor
manufacturers data sheet usually provides this information.
The value for the output capacitor COUT shown in Figure 18
should work for most applications, however it is not
necessarily the optimized solution.
IOUT
IIN
VIN
SMART
REGULATOR®
VOUT
} Control
Features
IQ
Figure 19. Single Output Regulator with Key
Performance Parameters Labeled
http://onsemi.com
10
NCV8504 Series
HEAT SINKS
A heat sink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment will have a thermal resistance. Like
series electrical resistances, these resistances are summed to
determine the value of RqJA:
Thermal Resistance,
Junction to Ambient, RqJA, (°C/W)
100
90
80
70
60
RqJA + RqJC ) RqCS ) RqSA
50
40
0
200
400
600
Copper Area (mm2)
(3)
where:
RqJC = the junction−to−case thermal resistance,
RqCS = the case−to−heatsink thermal resistance, and
RqSA = the heatsink−to−ambient thermal resistance.
RqJC appears in the package section of the data sheet. Like
RqJA, it too is a function of package type. RqCS and RqSA are
functions of the package type, heatsink and the interface
between them. These values appear in heat sink data sheets
of heat sink manufacturers.
800
Figure 20. 16 Lead SOW (Exposed Pad), qJA as a
Function of the Pad Copper Area (2 oz. Cu
Thickness), Board Material = 0.0625, G−10/R−4
ORDERING INFORMATION
Device
Output Voltage
NCV8504PWADJG
NCV8504PWADJR2G
Adjustable
NCV8504PW25G
NCV8504PW25R2G
2.5 V
NCV8504PW33G
NCV8504PW33R2G
3.3 V
NCV8504PW50G
NCV8504PW50R2G
5.0 V
Package
Shipping†
SOW−16 Exposed Pad
(Pb−Free)
47 Units/Rail
SOW−16 Exposed Pad
(Pb−Free)
1000 Tape & Reel
SOW−16 Exposed Pad
(Pb−Free)
47 Units/Rail
SOW−16 Exposed Pad
(Pb−Free)
1000 Tape & Reel
SOW−16 Exposed Pad
(Pb−Free)
47 Units/Rail
SOW−16 Exposed Pad
(Pb−Free)
1000 Tape & Reel
SOW−16 Exposed Pad
(Pb−Free)
47 Units/Rail
SOW−16 Exposed Pad
(Pb−Free)
1000 Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specification Brochure, BRD8011/D.
http://onsemi.com
11
NCV8504 Series
PACKAGE DIMENSIONS
SOIC 16 LEAD WIDE BODY
EXPOSED PAD
PDW SUFFIX
CASE 751AG−01
ISSUE A
−U−
A
M
P
0.25 (0.010)
M
W
M
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER
SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION SHALL BE
0.13 (0.005) TOTAL IN EXCESS OF THE D DIMENSION
AT MAXIMUM MATERIAL CONDITION.
6. 751R-01 OBSOLETE, NEW STANDARD 751R-02.
9
B
1
R x 45_
8
−W−
G
PIN 1 I.D.
14 PL
DETAIL E
TOP SIDE
C
F
−T−
0.10 (0.004) T
K
D 16 PL
0.25 (0.010)
T U
M
SEATING
PLANE
W
S
J
S
DETAIL E
H
EXPOSED PAD
1
SOLDERING FOOTPRINT*
8
0.350
L
16
DIM
A
B
C
D
F
G
H
J
K
L
M
P
R
0.050
BACK SIDE
CL
0.200
INCHES
MIN
MAX
0.400
0.411
0.292
0.299
0.093
0.104
0.014
0.019
0.020
0.035
0.050 BSC
0.136
0.144
0.010
0.012
0.000
0.004
0.186
0.194
0_
7_
0.395
0.415
0.010
0.029
Exposed
Pad
0.175
9
MILLIMETERS
MIN
MAX
10.15
10.45
7.40
7.60
2.35
2.65
0.35
0.49
0.50
0.90
1.27 BSC
3.45
3.66
0.25
0.32
0.00
0.10
4.72
4.93
0_
7_
10.05
10.55
0.25
0.75
0.188
CL
0.376
0.074
0.150
0.024
DIMENSIONS: INCHES
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SMART REGULATOR is a registered trademark of Semiconductor Components Industries, LLC (SCILLIC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
12
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCV8504/D