CLG-150 150W Single Output Switching Power Supply series Features : Universal AC input / Full range (up to 295VAC) Built-in active PFC function High efficiency up to 91% Protections: Short circuit / Over current / Over voltage / Over temperature Cooling by free air convection OCP point adjustable through output cable or internal potentiometer IP65 / IP67 design for indoor or outdoor installations Suitable for LED lighting and moving sign applications Compliance to worldwide safety regulations for lighting 3 years warranty 110 F CLG-150-12 A SELV IP65 IP67 (option) Blank : IP67 rated. Cable for I/O connection. A : IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. B : IP67 rated. Constant current level adjustable through output cable. C : Terminal block for I/O connection. Output voltage and constant current level can be adjusted through internal potentiometer. SPECIFICATION MODEL DC VOLTAGE CLG-150-12 CLG-150-15 CLG-150-20 CLG-150-24 CLG-150-30 CLG-150-36 CLG-150-48 12V 15V 20V 24V 30V 36V 48V 36 ~ 48V CONSTANT CURRENT REGION Note.4 9 ~12V OUTPUT 11.25 ~ 15V 15 ~ 20V 18 ~ 24V 11A 9.5A 7.5A 6.3A 22.5 ~ 30V 5A 27 ~ 36V RATED CURRENT 4.2A 3.2A RATED POWER 132W 142.5W 150W 151.2W 150W 151.2W 153.6W RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p 200mVp-p VOLTAGE ADJ. RANGE Note.6 9 ~ 13V 13 ~ 17V 17 ~ 22V 22 ~ 27V 26 ~ 32V 31 ~ 41V 40 ~ 56V 2.5 ~ 5A 2.1 ~ 4.2A 1.6 ~ 3.2A CURRENT ADJ. RANGE 4.75 ~ 9.5A 3.75 ~ 7.5A 3.15 ~ 6.3A 2.0% 2.0% 2.0% 1.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 1.0% 1.0% 1.0% 0.5% 0.5% 0.5% 0.5% 3000ms, 80ms at full load 50ms / 230VAC HOLD UP TIME (Typ.) VOLTAGE RANGE Note.5 90 ~ 295VAC 230VAC /115VAC 16ms / 115VAC at full load 127 ~ 417VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.98/115VAC, PF>0.95/230VAC, PF>0.93/277VAC at full load (Please refer to "Power Factor Characteristic" curve) EFFICIENCY (Typ.) 88% AC CURRENT (Typ.) INRUSH CURRENT(max.) 2A / 115VAC 1A / 230VAC COLD START 65A/230VAC LEAKAGE CURRENT OVER CURRENT (Typ.) Note.4 SHORT CIRCUIT PROTECTION 5.5 ~ 11A VOLTAGE TOLERANCE Note.3 SETUP, RISE TIME INPUT Can be adjusted by internal potentiometer or through output cable OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT 88% 90% 90% 91% 91% <1mA / 240VAC 95 ~ 108% Protection type : Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed 13.5 ~ 16V 18 ~ 20V 23 ~ 27V 28 ~ 34V 33 ~ 36V 42 ~ 48V 100 10 (RTH2) Protection type : Shut down o/p voltage, re-power on to recover -30 ~ +70 (Refer to "Derating Curve") 20 ~ 95% RH non-condensing -40 ~ +80 0.03%/ , 10 ~ 95% RH (0 ~ 50 ) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS Note.7 UL8750, CSA C22.2 No. 250.0-08, UL1012, CAN/CSA-C22.2 No. 107.1-01, EN61347-1, EN61347-2-13 independent (except for CLG-150 C type), UL60950-1, TUV EN60950-1,IP65 or IP67, J61347-1(option, except for CLG-150 C type), J61347-2-13 approved I/P-O/P:3.75KVAC EMC ISOLATION RESISTANCE EMC EMISSION I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C ( EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A MTBF 303.7Khrs min. MIL-HDBK-217F (25 ) 222.2*68*38.8mm (L*W*H)(CLG-150-Blank/A/B) 1.0Kg; 12pcs/13Kg/0.58CUFT(CLG-150-Blank/A/B) DIMENSION PACKING NOTE 59 ~ 70V Protection type : Shut down and latch off o/p voltage, re-power on to recover SAFETY & WITHSTAND VOLTAGE OTHERS 91% 0.68A / 277VAC I/P-FG:1.88KVAC O/P-FG:0.5KVAC 75% load) ; EN61000-3-3 229*68*38.8mm (L*W*H)(CLG-150-C) 1Kg; 12pcs/13Kg/0.96CUFT(CLG-150-C) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Constant current operation region is within 75% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. 5. Derating may be needed under low input voltages. Please check the static characteristics for more details. 6. Type A and type C only. 7. Safety and EMC design refer to EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18. 8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. File Name:CLG-150-SPEC 2012-03-12 CLG-150 150W Single Output Switching Power Supply Mechanical Specification Case No. 954A series Unit:mm Blank:(CLG-150) 222.2 198.2 12 9.4 9.6 300 20 34.2 300 20 T case 68 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) +V(Red) -V(Black) SJTW 14AWG 2C 9.4 34 SJTW 18AWG 3C 99.1 4.2 4PL 38.8 T case: Max. Case Temperature. IP67 rated. Cable for I/O connection. A Type:(CLG-150-_A) 222.2 198.2 12 9.4 9.6 Io ADJ. 34 9.4 SJTW 18AWG 3C T case 68 34.2 300 20 300 20 99.1 +V(Red) -V(Black) SJTW 14AWG 2C Vo ADJ. 4.2 4PL T case: Max. Case Temperature. 38.8 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.) File Name:CLG-150-SPEC 2012-03-12 CLG-150 150W Single Output Switching Power Supply series B Type:(CLG-150-_B) 222.2 198.2 12 9.6 9.4 300 20 SJTW 14AWG 2C 300 20 34.2 T case 68 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) 99.1 SJTW 18AWG 2C 9.4 34 SJTW 18AWG 3C +V(Red) -V(Black) ADJ1(Blue) ADJ2(White) 4.2 4PL 38.8 T case: Max. Case Temperature. IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistor between ADJ1 and ADJ2. Reference resistance value for output current adjustment (Typical) Resistance Percentage of rated current Open Slightly > 100% 4.7K 100% 620 75% 82 50% Short Slightly < 50% C Type:(CLG-150-_C) 229 198.2 15.4 8 8 AC Input Terminal Pin No. Assignment 68 T case 37 2 1 99.1 2 34 3 O/P Vo ADJ. 8 4.2 4PL T case: Max. Case Temperature. Pin No. 1 2 3 Assignment FG AC/N AC/L DC Output Terminal Pin No. Assignment 38.8 7.5 I/P 9.5 Io ADJ. 1 Pin No. 1 2 Assignment +V -V Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.) File Name:CLG-150-SPEC 2012-03-12 CLG-150 150W Single Output Switching Power Supply series Block Diagram Fosc : 100KHz EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER POWER SWITCHING PFC CIRCUIT +V -V ADJ1 ADJ2 (B Type) O.L.P. FG O.L.P. DETECTION CIRCUIT PWM & PFC CONTROL PFC CONTROL O.V.P. Derating Curve Static Characteristics 100 230VAC 100 90 80 230VAC Input only 80 100VAC 70 LOAD (%) LOAD (%) 60 40 20 -30 -25 -10 0 15 30 50 55 60 AMBIENT TEMPERATURE ( ) 70 (HORIZONTAL) 60 50 40 90 100 125 135 145 155 165 175 180 200 230 295 INPUT VOLTAGE (V) 60Hz File Name:CLG-150-SPEC 2012-03-12 CLG-150 150W Single Output Switching Power Supply series Power Factor Characteristic PF Constant Current Mode 1 0 0 0 0 0 0 0 0 0 0 0 .0 .9 .9 .9 .9 .9 .8 .8 .8 .8 .8 .7 0 8 6 4 2 0 8 6 4 2 0 8 277V ac 230V ac 115V ac 50% 60% 70% 80% 90% 100% (150W) LOAD EFFICIENCY vs LOAD (48V Model) CLG-150 series possess superior working efficiency that up to 91% can be reached in field applications. 96 92 EFFICIENCY (%) 88 84 277Vac 80 230Vac 76 115Vac 72 68 64 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode [with LED driver, at area (A)] and CC mode [direct drive, at area (B)]. Vo(%) 100 (B) Constant Current area (A) Constant Voltage area 75 (max.) (C) Hiccup Protection 75 100 Io (%) Typical LED power supply I-V curve File Name:CLG-150-SPEC 2012-03-12