DSA150 Series AC-DC Power Supplies 150 Watts xxx Series • Ultra Slim Design • 150% Peak Load for 3 seconds • Ambient Operation from -10 °C to +70 °C • High Efficiency • Selectable Overload Characteristic • Selectable Remote Inhibit or Enable • 3 Year Warranty Dimensions: DSA150: 3.92 x 4.92 x 2.18” (99.8 x 125.2 x 55.5 mm) Models & Ratings Output Voltage 24 V 48 V Output Power 150 W 150 W Output Voltage Trim(3) 23.52-25.92 V 47.04-51.84 V Output Current 6.25 A 3.125 A Peak Load(2) 9.45 A 4.8 A Typical Efficiency(1) 87% 87% Model Number DSA150PS24 DSA150PS48 Notes 1. Typical efficiency at 230 VAC and full load. 2. Peak load is for a maximum of 3 s, see Application Notes. Average power is not to exceed nominal output power. 3. Output current should be limited so that nominal output power is not exceeded. Mechanical Details 1 +V 3.92 (99.8) 6 Pin Connector 2.18 (55.5) -V +RC -RC DC OK VOUT ADJ. ON 1 4.92 (125.2) 2 OCP Mode RC Mode DSA150 www.xppower.com L 1 N www.xppower.com Conn Pin 1 AC 2 I/P 3 1 2 3 DC O/P 4 5 6 Designation Ground L N +Vout -Vout +RC -RC DC OK DC OK DSA150 Series AC-DC Power Supplies Input Characteristic Minimum Input Voltage - Operating 90 Input Frequency 47 Power Factor Typical 50/60 Units 264 VAC 63 Hz Notes & Conditions 0.9 Input Current - Full Load At 230 VAC. Conforms to EN61000-3-2 Class A 1.6/0.8 Inrush Current Earth Leakage Current Input Protection Maximum A 115/230 VAC 33/65 A At 115/230 VAC 1.0 mA Maximum Units Notes & Conditions 48 VDC See Models and Ratings table ±1 % -2/+8 % See Models and Ratings table A No minimum load required At 264 VAC, 60 Hz T5.0 A / 250 V internal in-line fuse Output Characteristic Output Voltage - V1 Minimum Typical 24 Initial Set Accuracy Output Voltage Adjustment Minimum Load 0 Start Up Delay 1.0 s Start Up Rise Time 50 ms Hold Up Time 18 ms Line Regulation ±0.5 % Load Regulation ±1 % Transient Response - V1 4 % Ripple & Noise Overvoltage Protection At 100% load At full load and 115 VAC Recovery within 1% in less than 2 ms for a 50% step load change at 0.2 A/µs 1 % pk-pk 28 33 V 24 V model 56 65 V 48 V model Overload Protection Measured at 20 MHz bandwidth % See Application Notes Trip & restart (hiccup mode) for 5 cycles then latch. Recycle AC to reset. Short Circuit Protection Thermal Protection Temperature Coefficient Remote On/Off 95 (±5) °C 0.03 %/˚C Measured on internal heatsink auto recovery Selectable as Enable or Inhibit using front panel switch General Characteristic Minimum Efficiency Isolation: Input to Output Input to Ground Output to Ground Switching Frequency Typical Maximum 87 Units % 3000 Notes & Conditions See Models & Ratings table VAC 1500 VAC 500 VAC 56/75 kHz PFC/Main converter DC OK Signal Volt free contacts rated at 60 VDC/0.3 A, 30 VDC/1.0 A or 30 VAC/0.5 A (resistive load) Output LED Green LED to indicate output on. Mean Time Between Failure Weight >250 kHrs 1.9 (860) lb (g) www.xppower.com MIL-HDBK-217F, +25 °C GB 2 DSA150 Series AC-DC Power Supplies Environmental Characteristic Maximum Units Operating Temperature Minimum -10 Typical +70 °C Storage Temperature -40 +85 °C 20 95 %RH 3000 m See derating curve in Application Notes Natural convection Cooling Operating Humidity Notes & Conditions Operating Altitude Non-condensing Shock IEC68-2-27, 4 g, 22 ms half sine, 3 times in each of 6 axes Vibration IEC68-2-6, 10-500 Hz, 2 g 10 mins/sweep. 60 mins for each of 3 axes EMC: Emissions Phenomenon Standard Test Level Conducted EN55022 Class B EN55022 Class B Harmonic Current EN61000-3-2 Class A Voltage Fluctuations EN61000-3-3 Radiated Criteria Notes & Conditions Criteria Contact EMC: Immunity Phenomenon Standard ESD Immunity EN61000-4-2 Radiated Immunity EN61000-4-3 Test Level 6 kV A 8 kV 10 V/m A EFT/Burst EN61000-4-4 3 A Surges EN61000-4-5 Installation class 3 A Conducted EN61000-4-6 10 V A Magnetic Fields EN61000-4-8 4 Dips and Interruptions EN55024 Notes & Conditions Air Discharge A Dip: 30%, 10 ms A Dip: 60%, 100 ms A/B High Line/Low Line B Dip: 100%, 5000 ms Safety Approvals 3 Safety Agency Safety Standard Notes & Conditions UL UL508 Industrial Control Equipment TUV EN60950-1 A12:2011 Information Technology CB IEC60950-1 +A1:2009 Information Technology www.xppower.com DSA150 Series AC-DC Power Supplies Mechanical Details 1 +V 3.92 (99.8) 6 Pin Connector Conn Pin 1 AC 2 I/P 3 1 2 3 DC O/P 4 5 6 2.18 (55.5) -V +RC -RC DC OK VOUT ADJ. ON 1 4.92 (125.2) 2 OCP Mode RC Mode DSA150 www.xppower.com L Designation Ground L N +Vout -Vout +RC -RC DC OK DC OK N Notes 1. All dimensions in inches (mm) 2. Weight: 1.916 lbs (860g) 3. Tolerance: ±0.02 in (±0.5 mm) 4. Screw terminal: 10-24 AWG cables size. 5. Connection screw maximum torque: Input: 4.4lbs-in (0.5 Nm), Output: 7.0 lbs-in (0.79 Nm). Application Notes Derating Curves 100 150 Load (%) Load (%) 90 For typ. 3sec 112.5 100 Continuous 50 80 70 60 50 40 -10 40 0 10 20 30 40 50 60 70 (Vertical) 90 Ambient Temperature (°C) DC OK 5 6 DCOK DCOK 100 110 135 230 264Vac Input Voltage(V) Open = Output fail, if voltage drops below 45% of nominal Closed = Output good Contact Rating: 0.3 A at 60 VDC, 1.0 A at 30 VDC, 0.5 A at 30 VAC. 500 VDC isolation to output. www.xppower.com 4 DSA150 Series AC-DC Power Supplies Application Notes Peak Loading The peak loading and overload characteristics can be programmed into one of two modes by appropriate selection of the OCP mode switch on the front panel. OCP Mode switch set to position 1 I A peak load of up-to 150% can be taken for a given duration. This duration depends on the percentage of peak load taken and can be determined by graph A below. T-peak I-peak If the load is reduced to less than 100% of nominal either before or at the end of the duration, then there is a period of recovery needed to allow the power supply to cool down before the peak load can be re-applied. The time required for recovery depends on the amount of reduction of load and can be determined by graph B below. I-recovery T-recovery 0 T However, if the peak load period exceeds the duration indicated by graph A the output will go into constant current mode for protection. The constant current value will be 105% of the nominal rating. During constant current operation, if the output voltage should fall below 40% of the rated voltage then the output will turn off and try to restart for five times before turning off permanently. Once this has happened, the output will need to be reset by turning the AC mains off and on again. A peak load of up-to 150% can be taken for a given duration. This duration depends on the percentage of peak load taken as described by graph A. OCP Mode switch set to position 2 I Once the peak load duration is exceeded, the output will turn off for 3-4 seconds before automatically restarting. T-peak I-peak GRAPH A 0 3 ~ 4 sec T Peak duration GRAPH B Recovery duration (Sec.) (Sec.) 24 22 20 18 16 14 12 10 8 6 4 2 0 22 20 18 16 14 12 10 8 6 4 2 0 110% 115% 120% 125% 130% 135% 140% 145% 150% I-peak Load (%) 10% 20% 30% 40% 50% 60% 70% 80% 90% I-normal Load (%) Remote Control The output can be controlled by applying a voltage between pin 3 of the DC output with respect to pin 4. The effect of the control is dependant upon the RC switch setting on the front panel. If the switch is set to position 1 then the output can be disabled by applying a suitable voltage. If the switch is set to position 2 then the output can be enabled by applying a voltage. In the range of 2.5 V to 9.0 V limited to 20 mA. Switch Position Pin 3 Voltage with respect to Pin 4 Output 1 <0.8 V or Open Circuit ON 1 >2.5 V, <9.0 V OFF 2 <0.8 V or Open Circuit OFF 2 >2.5 V, <9.0 V ON www.xppower.com 28-May-15