ON MC74HC153ADTR2G Dual 4-input data selector/multiplexer Datasheet

MC74HC153A
Dual 4-Input Data
Selector/Multiplexer
High−Performance Silicon−Gate CMOS
The MC74HC153 is identical in pinout to the LS153. The device
inputs are compatible with standard CMOS outputs; with pullup
resistors, they are compatible with LSTTL outputs.
The Address Inputs select one of four Data Inputs from each
multiplexer. Each multiplexer has an active−low Strobe control and a
noninverting output.
The HC153 is similar in function to the HC253, which has 3−state
outputs.
http://onsemi.com
16
MARKING
DIAGRAMS
SOIC−16
D SUFFIX
CASE 751B
16
1
HC153AG
AWLYWW
1
16
Features
•
•
•
•
•
•
Output Drive Capability: 10 LSTTL Loads
Outputs Directly Interface to CMOS, NMOS, and TTL
Operating Voltage Range: 2 to 6 V
Low Input Current: 1 mA
High Noise Immunity Characteristic of CMOS Devices
These are Pb−Free Devices
ADDRESS
INPUTS
D0a 6
D1 5
1
A
= Assembly Location
WL, L
= Wafer Lot
YY, Y
= Year
WW, W = Work Week
G or G
= Pb−Free Package
(Note: Microdot may be in either location)
PIN ASSIGNMENT
7 Y
a
a
D2a
STROBE a
1
16
VCC
A1
2
15
STROBE b
D3a
3
14
A0
D2a
4
13
D3b
D1a
5
12
D2b
D0a
6
11
D1b
Ya
7
10
D0b
GND
8
9
Yb
4
D3a 3
STROBE a 1
DATAWORD b
INPUTS
D0b 10
D1 11
HC
153A
ALYWG
G
1
A0 14
A1 2
DATAWORD a
INPUTS
TSSOP−16
DT SUFFIX
CASE 948F
16
9 Y
b
FUNCTION TABLE
b
D2b 12
D3 13
Inputs
b
STROBE b 15
PIN 16 = VCC
PIN 8 = GND
Output
A1
A0
Strobe
Y
X
L
L
H
H
X
L
H
L
H
H
L
L
L
L
L
D0
D1
D2
D3
D0, D1, D2, and D3 = the level of the respective
data input.
Figure 1. Logic Diagram
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
© Semiconductor Components Industries, LLC, 2013
May, 2013 − Rev. 1
1
Publication Order Number:
MC74HC153A/D
MC74HC153A
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
−0.5 to + 7.0
V
DC Input Voltage (Referenced to GND)
−1.5 to VCC + 1.5
V
DC Output Voltage (Referenced to GND)
−0.5 to VCC + 0.5
V
VCC
DC Supply Voltage (Referenced to GND)
Vin
Vout
Iin
DC Input Current, per Pin
±20
mA
Iout
DC Output Current, per Pin
±25
mA
ICC
DC Supply Current, VCC and GND Pins
±50
mA
PD
Power Dissipation in Still Air
500
TBD
mW
Tstg
Storage Temperature
−65 to +150
°C
SOIC Package
TSSOP Package
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND v (Vin or Vout) v VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress
ratings only. Functional operation above the Recommended Operating Conditions is not implied.
Extended exposure to stresses above the Recommended Operating Conditions may affect device
reliability.
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Vin, Vout
Parameter
DC Supply Voltage (Referenced to GND)
DC Input Voltage, Output Voltage (Referenced to GND)
TA
Operating Temperature, All Package Types
tr, tf
Input Rise and Fall Time
(Figure 2)
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
Min
Max
Unit
2.0
6.0
V
0
VCC
V
−55
+125
°C
0
0
0
1000
500
400
ns
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
Guaranteed Limit
Symbol
Parameter
Test Conditions
VCC
V
− 55 to
25°C
v 85°C
v 125°C
Unit
VIH
Minimum High−Level Input
Voltage
Vout = 0.1 V or VCC − 0.1 V
|Iout| v 20 mA
2.0
4.5
6.0
1.5
3.15
4.2
1.5
3.15
4.2
1.5
3.15
4.2
V
VIL
Maximum Low−Level Input
Voltage
Vout = 0.1 V or VCC − 0.1 V
|Iout| v 20 mA
2.0
4.5
6.0
0.3
0.9
1.2
0.3
0.9
1.2
0.3
0.9
1.2
V
VOH
Minimum High−Level Output
Voltage
Vin = VIH or VIL
|Iout| v 20 mA
2.0
4.5
6.0
1.9
4.4
5.9
1.9
4.4
5.9
1.9
4.4
5.9
V
4.5
6.0
3.98
5.48
3.84
5.34
3.70
5.20
2.0
4.5
6.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
4.5
6.0
0.26
0.26
0.33
0.33
0.40
0.40
Vin = VIH or VIL
VOL
Maximum Low−Level Output
Voltage
|Iout| v 4.0 mA
|Iout| v 5.2 mA
Vin = VIH or VIL
|Iout| v 20 mA
Vin = VIH or VIL
|Iout| v 4.0 mA
|Iout| v 5.2 mA
V
Iin
Maximum Input Leakage Current
Vin = VCC or GND
6.0
±0.1
±1.0
±1.0
mA
ICC
Maximum Quiescent Supply
Current (per Package)
Vin = VCC or GND
Iout = 0 mA
6.0
8
80
160
mA
http://onsemi.com
2
MC74HC153A
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
Guaranteed Limit
Parameter
Symbol
VCC
V
− 55 to
25°C
v 85°C
v 125°C
Unit
tPLH,
tPHL
Maximum Propagation Delay, Input D to Output Y
(Figures 2 and 5)
2.0
4.5
6.0
140
28
24
175
35
30
210
42
36
ns
tPLH,
tPHL
Maximum Propagation Delay, Input A to Output Y
(Figures 3 and 5)
2.0
4.5
6.0
175
35
30
220
44
37
265
53
45
ns
tPLH,
tPHL
Maximum Propagation Delay, Strobe to Output Y
(Figures 4 and 5)
2.0
4.5
6.0
95
19
16
120
24
20
145
29
25
ns
tTLH,
tTHL
Maximum Output Transition Time, Any Output
(Figures 2 and 5)
2.0
4.5
6.0
75
15
13
95
19
16
110
22
19
ns
Maximum Input Capacitance
—
10
10
10
pF
Cin
Typical @ 25°C, VCC = 5.0 V
CPD
31
Power Dissipation Capacitance (Per Multiplexer)
pF
SWITCHING WAVEFORMS
tr
tf
VALID
INPUT D
VCC
50%
INPUT A
GND
tPLH
GND
tPLH
tPHL
90%
50%
10%
OUTPUT Y
OUTPUT Y
tTLH
tPHL
50%
tTHL
Figure 2.
Figure 3.
tf
tr
90%
STROBE 50%
10%
TEST POINT
VCC
OUTPUT
DEVICE
UNDER
TEST
GND
tPLH
tPHL
90%
50%
10%
OUTPUT Y
VALID
VCC
90%
50%
10%
tTLH
CL*
tTHL
*Includes all probe and jig capacitance
Figure 4.
Figure 5. Test Circuit
http://onsemi.com
3
MC74HC153A
PIN DESCRIPTIONS
DATA INPUTS
Strobe (Pins 1, 15)
D0a − D3a, D0b − D3b (Pins 3, 4, 5, 6, 10, 11, 12, 13)
Active−low Strobe. A low level applied to these pins
enables the corresponding outputs.
Data Inputs. With the outputs enabled, the addressed Data
Inputs appear at the Y outputs.
OUTPUTS
CONTROL INPUTS
Ya, Yb (Pins 7, 9)
Noninverting data outputs.
A0, A1 (Pins 2, 14)
Address Inputs. These inputs address the pair of Data
Inputs which appear at the corresponding outputs.
D0a 6
STROBE a
DATA
WORD a
INPUTS
1
D1a 5
D2a
7 Y
a
4
D3a 3
NONINVERTING
DATA
OUTPUTS
D0b 10
DATA
WORD b
INPUTS
D1b 11
9
D2b 12
STROBE b 15
D3b 13
ADDRESS
INPUTS
Yb
A1 2
A0 14
Figure 6. Expanded Logic Diagram
ORDERING INFORMATION
Package
Shipping†
MC74HC153ADG
SOIC−16
(Pb−Free)
48 Units / Rail
MC74HC153ADR2G
SOIC−16
(Pb−Free)
2500 Tape & Reel
MC74HC153ADTR2G
TSSOP−16*
2500 Tape & Reel
MC74HC153ADTG
TSSOP−16*
96 Units / Tube
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*This package is inherently Pb−Free.
http://onsemi.com
4
MC74HC153A
PACKAGE DIMENSIONS
TSSOP−16
DT SUFFIX
CASE 948F−01
ISSUE B
16X K REF
0.10 (0.004)
0.15 (0.006) T U
T U
M
S
V
S
K
S
K1
2X
L/2
16
9
B
−U−
L
SECTION N−N
J
PIN 1
IDENT.
N
8
1
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
J1
0.25 (0.010)
M
0.15 (0.006) T U
S
A
−V−
N
F
DETAIL E
C
0.10 (0.004)
−T− SEATING
PLANE
D
H
G
DETAIL E
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH. PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
MILLIMETERS
INCHES
DIM MIN
MAX
MIN
MAX
A
4.90
5.10 0.193 0.200
B
4.30
4.50 0.169 0.177
C
−−−
1.20
−−− 0.047
D
0.05
0.15 0.002 0.006
F
0.50
0.75 0.020 0.030
G
0.65 BSC
0.026 BSC
H
0.18
0.28 0.007
0.011
−W−
J
0.09
0.20 0.004 0.008
J1
0.09
0.16 0.004 0.006
K
0.19
0.30 0.007 0.012
K1
0.19
0.25 0.007 0.010
L
6.40 BSC
0.252 BSC
M
0_
8_
0_
8_
SOLDERING FOOTPRINT*
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
5
MC74HC153A
PACKAGE DIMENSIONS
SOIC−16
CASE 751B−05
ISSUE K
−A−
16
9
1
8
−B−
P
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
8 PL
0.25 (0.010)
M
B
S
DIM
A
B
C
D
F
G
J
K
M
P
R
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
16 PL
0.25 (0.010)
M
T B
S
A
S
SOLDERING FOOTPRINT*
8X
6.40
16X
1
1.12
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
6
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC74HC153A/D
Similar pages