EMG4 / UMG4N / FMG4A Transistors General purpose (dual digital transistors) EMG4 / UMG4N / FMG4A zExternal dimensions (Unit : mm) zFeatures 1) Two DTC114T chips in a EMT or UMT or SMT package. 0.22 (2) zEquivalent circuits (3) R1 (4) R1 (5) R1 Each lead has same dimensions ROHM : EMT5 (5) (2) (1) EMG4 UMG4N FMG4A 1.25 EMT5 UMT5 SMT5 2.1 Marking Code G4 T2R G4 TR G4 T148 Basic ordering unit (pieces) 8000 3000 3000 0.1Min. 2.0 0~0.1 Type Package 0.15 (5) zPackage, marking, and packaging specifications (2) 0.2 (4) UMG4N 1.3 R1=10kΩ (3) R1=10kΩ (1) (4) 0.65 0.65 R1 0.5 FMG4A (1) (1) 0.9 (2) 1.2 1.6 0.7 (3) (5) 0.13 EMG4 / UMG4N (3) (4) 0.5 0.5 1.0 1.6 EMG4 Each lead has same dimensions ROHM : UMT5 EIAJ : SC-88A zAbsolute maximum ratings (Ta=25°C) V 100 mA Junction temperature Storage temperature ∗1 120mW per element must not be exceeded. ∗2 200mW per element must not be exceeded. EMG4 / UMG4N Pd 150(TOTAL) mW 300(TOTAL) FMG4A ∗1 ∗2 Tj 150 °C 1.6 Tstg −55 to +150 °C 2.8 0.3Min. ROHM : SMT5 EIAJ : SC-74A 0~0.1 Power dissipation 2.9 5 IC 1.1 VEBO Collector current 0.95 0.95 1.9 Emitter-base voltage FMG4A 0.8 V (3) 50 (4) VCEO (5) V Collector-emitter voltage (2) Unit 50 (1) Limits VCBO 0.15 Parameter 0.3 Symbol Collector-base voltage Each lead has same dimensions Rev.A 1/2 EMG4 / UMG4N / FMG4A Transistors zElectrical characteristics (Ta=25°C) Symbol Min. Typ. Max. Unit Collector-base breakdown voltage Parameter BVCBO 50 − − V IC=50µA Collector-emitter breakdown voltage BVCEO 50 − − V IC=1mA Emitter-base breakdown voltage Collector cutoff current BVEBO ICBO 5 − − − − 0.5 V µA IE=50µA VCB=50V VEB=4V Emitter cutoff current Collector-emitter saturation voltage DC current transfer ratio Conditions IEBO − − 0.5 µA VCE(sat) − − 0.3 V IC/IB=10mA/1mA hFE 100 250 600 − VCE=5V, IC=1mA Transition frequency fT − 250 − MHz Input resistance R1 7 10 13 kΩ VCE=10V, IE= −5mA, f=100MHz ∗ − ∗Transition frequency of the device. 1k VCE=5V DC CURRENT GAIN : hFE 500 200 Ta=100°C 25°C −40°C 100 50 20 10 5 2 1 100µ 200µ 500µ 1m 2m 5m 10m 20m 50m 100m COLLECTOR CURRENT : IC (A) Fig.1 DC current gain vs. collector current COLLECTOR SATURATION VOLTAGE : VCE(sat) (V) zElectrical characteristics curves 1 lC/lB=10 500m 200m Ta=100°C 25°C −40°C 100m 50m 20m 10m 5m 2m 1m 100µ 200µ 500µ 1m 2m 5m 10m 20m 50m 100m COLLECTOR CURRENT : IC (A) Fig.2 Collector-emitter saturation voltage vs. collector current Rev.A 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1