HI-15530 5V / 3.3V Manchester Encoder / Decoder August 2006 GENERAL DESCRIPTION FEATURES The HI-15530 is a high performance CMOS integrated circuit designed to meet the requirements of MIL-STD-1553 and similar Manchester II encoded, time division multiplexed serial data protocols. The HI-15530 contains both an Encoder and Decoder, which operate independently. The HI-15530 is fully compatible with either 5V or 3.3V logic and transceivers. The device generates MIL-STD-1553 sync pulses, parity bits as well as the Manchester II encoding of the data bits. The decoder recognizes and identifies sync pulses, decodes data bits, and performs parity checking. The HI-15530 supports the 1Mbit/s data rate of MIL-STD1553 over the full temperature and voltage range. For applications requiring small footprints and low cost, the HI-15530 is available in a 24-pin plastic SSOP package. Ceramic DIP and LCC packages are also available to achieve the highest level of reliability and to provide drop-in replacements for obsolete parts from other manufacturers. ! MIL-STD-1553 compatible ! 5V or 3.3V operation ! Interfaces to HI-1567 Transceiver Family ! Small footprint 24-pin plastic SSOP package option ! Direct replacement for: Harris/Intersil HD15530 GEC Plessey Semiconductors MAS15530 Aeroflex ACT15530 ! 1.25 Mbit/s Maximum Data Rate ! Manchester II Encode and Decode ! Sync identification and Lock-in PIN CONFIGURATION (Top View) VALID WORD 1 24 VDD ENCODER SHIFT CLK 2 23 ENCODER CLK TAKE DATA 3 22 SEND CLK IN ! MIL-STD-1553 Interfaces SERIAL DATA OUT 4 21 SEND DATA DECODER CLK 5 ! Smart Munitions BIPOLAR ZERO IN 6 BIPOLAR ONE IN 7 APPLICATIONS ! Stores management ! Sensor interfaces ! Instrumentation 20 SYNC SELECT HI-15530PSI HI-15530PST HI-15530PSM 19 ENCODER ENABLE 18 SERIAL DATA IN UNIPOLAR DATA IN 8 17 BIPOLAR ONE OUT DECODER SHIFT CLK 9 16 OUTPUT INHIBIT COMMAND / DATA SYNC 10 DECODER RESET 11 GND 12 15 BIPOLAR ZERO OUT 14 ¸ 6 OUT 13 MASTER RESET 24 Pin SSOP package (See page 3-43 for additional Package Pin Configurations) (DS15530 Rev. G) HOLT INTEGRATED CIRCUITS www.holtic.com 08/06 HI-15530 PIN DESCRIPTIONS SIGNAL SECTION FUNCTION VALID WORD ENCODER SHIFT CLOCK TAKE DATA DECODER ENCODER DECODER OUTPUT OUTPUT OUTPUT SERIAL DATA OUT DECODER CLOCK DECODER DECODER OUTPUT INPUT BIPOLAR ZERO IN DECODER INPUT BIPOLAR ONE IN DECODER INPUT UNIPOLAR DATA IN DECODER INPUT DECODER SHIFT CLOCK DECODER OUTPUT COMMAND / DATA SYNC DECODER OUTPUT DECODER RESET DECODER INPUT BOTH BOTH POWER INPUT ¸6 OUT BIPOLAR ZERO OUT ENCODER ENCODER OUTPUT OUTPUT OUTPUT INHIBIT ENCODER INPUT BIPOLAR ONE OUT ENCODER OUTPUT SERIAL DATA IN ENCODER ENABLE ENCODER ENCODER INPUT INPUT SYNC SELECT ENCODER INPUT SEND DATA ENCODER OUTPUT SEND CLOCK IN ENCODER CLOCK VDD ENCODER ENCODER BOTH INPUT INPUT POWER GND MASTER RESET DESCRIPTION A high output signals the receipt of a valid word Shifts data into the encoder on a low to high transition Output is high during receipt of data after identification of a Sync Pulse and two valid Manchester data bits. Received Data output in NRZ format 12x the data rate. Clock for the transition finder and synchronizer, which generates the internal clock for the remainder of the decoder A high input indicates the 1553 bus is in its negative state. This pin must be held high when the Unipolar input is used A high input indicates the 1553 bus is in the positive state. This pin must be held low when the Unipolar input is used Input for unipolar data to the transition finder. Must be held low when Not in use Provides the DECODER CLOCK divided by 12, synchronized by the recovered serial data A high on this pin occurs during the output of decoded data which was preceded by a Command (or Status) synchronizing character. A low output indicates a Data synchronizing character A high applied to this pin during a DECODER SHIFT CLOCK rising edge resets the bit counter 0V supply A high on this pin clears the 2:1 counters in both Encoder and Decoder and resets the divide-by-6 circuit Provides ENCODER CLOCK divided by 6 An active low output intended to drive the zero or negative sense of a MIL-STD-1553 Line Driver A low inhibits the BIPOLAR ZERO OUT and BIPOLAR ONE OUT by forcing them to inactive high states An active low output intended to drive the one or positive sense on a MIL-STD-1553 Line Driver Accepts serial data at the rate of the ENCODER SHIFT CLOCK A high on this pin initiates the encode cycle. (Subject to the preceeding cycle being complete) Actuates a Command Sync for an input high and a Data Sync for a low An active high output which enables the external source of serial Data Clock input at 2 times the Data rate, usually driven by ¸6 OUT Input to the divide by 6 circuit. Normal frequency is Data rate x12 3.0 V to 5.5 V power supply pin HOLT INTEGRATED CIRCUITS 2 HI-15530 ENCODER OPERATION The Encoder requires a single clock with a frequency of twice the desired data rate applied at the SEND CLOCK input. An auxiliary divide-by-six counter is provided on chip which can be utilized to produce the SEND CLOCK by dividing the ENCODER CLOCK. To abort the Encoder transmission a positive pulse must be applied at MASTER RESET. Anytime after or during this pulse, a low to high transition on SEND CLOCK clears the internal counters and initializes the Encoder for a new word. The Encoder's cycle begins when ENCODER ENABLE is high during a falling edge of ENCODER SHIFT CLOCK (1). This cycle lasts for one word length or twenty ENCODER SHIFT CLOCK periods. At the next low-to-high transition of the ENCODER SHIFT CLOCK, a high at SYNC SELECT input actuates a command sync or a low will produce a data sync for that word (2). When the Encoder is ready to accept data, the SEND DATA output will go high and remain high for sixteen ENCODER SHIFT CLOCK periods (3). During these sixteen periods the data should be clocked into the SERIAL DATA IN input with every low-tohigh transition of the ENCODER SHIFT CLOCK (3) - (4). After the sync and the Manchester II coded data are transmitted through the BIPOLAR ONE and BIPOLAR ZERO outputs, the Encoder adds on an additional bit which is the parity for that word (5). If ENCODER ENABLE is held high continuously, consecutive words will be encoded without an interframe gap. ENCODER ENABLE must go low by time (5) as shown to prevent a consecutive word from being encoded. At any time a low on the OUTPUT INHIBIT input will force both bipolar outputs to a high state but will not affect the Encoder in any other way. TIMING 0 1 2 3 4 MASTER RESET OUTPUT INHIBIT SEND CLK IN BIPOLAR ONE OUT ¸ 6 OUT ¸2 Character Former ¸6 ENCODER CLK Bit Counter SYNC SELECT SEND DATA ENCODER SHIFT CLK SERIAL DATA IN ENCODER ENABLE FIGURE 1. ENCODER 5 6 7 15 16 17 18 19 SEND CLK ENCODER SHIFT CLK ENCODER ENABLE SYNC SELECT DON’T CARE VALID DON’T CARE SEND DATA SERIAL DATA IN 15 14 13 12 11 10 3 2 1 0 BIPOLAR ONE OUT SYNC SYNC 15 14 13 12 11 3 2 1 0 P BIPLOAR ZERO OUT SYNC SYNC 15 14 13 12 11 3 2 1 0 P (1) (2) (3) FIGURE 2. ENCODER OPERATION HOLT INTEGRATED CIRCUITS 3 (4) (5) BIPOLAR ZERO OUT HI-15530 DECODER OPERATION The Decoder requires a single clock with a frequency of 12 times the desired data rate applied at the DECODER CLOCK input. The Manchester II coded data can be presented to the Decoder in one of two ways. The BIPOLAR ONE and BIPOLAR ZERO inputs will accept data from a comparator sensed transformer coupled bus as specified in MIL-STD-1553. The UNIPOLAR DATA input can only accept non-inverted Manchester II coded data (e.g. from BIPOLAR ZERO OUT of an Encoder). The Decoder is free running and continuously monitors its data input lines for a valid sync character and two valid Manchester data bits to start an output cycle. When a valid sync is recognized (1), the type of sync is indicated on COMMAND/DATA SYNC output. If the sync character was a command sync, this output will go high (2) and remain high for sixteen DECODER SHIFT CLOCK periods (3), otherwise it will remain low. The TAKE DATA output will go high and remain high (2) - (3) while the Decoder is transmitting the decoded data through SERIAL DATA OUT. The decoded data available at SERIAL DATA OUT is in an NRZ format. The DECODER SHIFT CLOCK is provided so that the decoded bits can be shifted into an external register on every low-to-high transition of this clock (2) - (3). After all sixteen decoded bits have been transmitted (3) the data is checked for odd parity. A high on VALID WORD output (4) indicates a successful reception of a word without any Manchester or parity errors. At this time the Decoder is TIMING 0 1 looking for a new sync character to start another output sequence. VALID WORD will go low approximately 20 DECODER SHIFT CLOCK periods after it goes high if not reset low sooner by a valid sync and two valid Manchester bits as shown (1). At any time in the above sequence, a high input on DECODER RESET during a low-to-high transition of DECODER SHIFT CLOCK will abort transmission and initialize the Decoder to start looking for a new sync character. TAKE DATA UNIPOLAR DATA IN BIPOLAR ONE IN TRANSITION FINDER CHARACTER IDENTIFIER COMMAND/DATA SYNC BIPOLAR ZERO IN SERIAL DATA OUT DECODER CLK BIT RATE CLK SYNCHRONIZER PARITY CHECK DECODER SHIFT CLK MASTER RESET DECODER RESET BIT COUNTER FIGURE 3. DECODER 2 3 4 5 6 7 8 16 17 18 19 DECODER SHIFT CLK BIPOLAR ONE IN SYNC SYNC 15 14 13 12 11 10 2 1 0 P BIPLOAR ZERO IN SYNC SYNC 15 14 13 12 11 10 2 1 0 P TAKE DATA COMMAND / DATA SYNC SERIAL DATA OUT VALID WORD UNDEFINED 15 14 13 12 4 3 2 1 0 May be high from previous reception (1)(2) FIGURE 4. DECODER OPERATION HOLT INTEGRATED CIRCUITS 4 VALID WORD (3) (4) HI-15530 TIMING DIAGRAMS SEND CLK t E1 ENCODER SHIFT CLK t E2 SERIAL DATA IN t E3 VALID VALID SEND CLK ENCODER SHIFT CLK t E1 t E4 ENCODER ENABLE t E6 t E5 VALID SYNC SELECT t E7 ENCODER SHIFT CLK t E8 SEND DATA SEND CLK t E9 BIPOLAR ONE OUT or BIPOLAR ZERO OUT ENCODER TIMING DECODER SHIFT CLK t D6 COMMAND / DATA SYNC t D7 TAKE DATA DECODER SHIFT CLK t D8 DATA BIT SERIAL DATA OUT DECODER SHIFT CLK t D9 COMMAND / DATA SYNC t D10 TAKE DATA t D11 VALID WORD DECODER SHIFT CLK t DRH DECODER RESET t DR t DRS DECODER TIMING HOLT INTEGRATED CIRCUITS 5 HI-15530 TIMING DIAGRAMS (cont.) BIT PERIOD BIPOLAR ONE IN BIT PERIOD t D1 t D3 t D2 BIPOLAR ZERO IN BIT PERIOD t D3 t D1 t D2 COMMAND SYNC BIPOLAR ONE IN t D1 t D3 t D3 BIPOLAR ZERO IN t D1 t D2 BIPOLAR ONE IN t D3 t D1 t D1 t D3 BIPOLAR ZERO IN t D2 DATA SYNC t D3 t D3 t D1 t D3 t D1 t D4 t D5 t D5 ONE t D4 ZERO ONE t D2 UNIPOLAR IN t D2 COMMAND SYNC t D2 UNIPOLAR IN t D2 DATA SYNC t D5 UNIPOLAR IN t D4 t D4 t D5 ONE ZERO t D4 ONE DECODER TIMING Bit Period Command Word Data Word Status Word 0 1 2 SYNC 3 4 5 6 7 TERMINAL ADDRESS 8 R/T SYNC SYNC 9 10 11 12 13 14 15 16 17 18 19 SUBADDRESS / MODE DATA WORD COUNT P P DATA WORD SYNC SYNC TERMINAL ADDRESS ME CODE FOR FAILURE MODES SYNC MIL-STD-1553 WORD FORMATS HOLT INTEGRATED CIRCUITS 6 TF P HI-15530 ABSOLUTE MAXIMUM RATINGS Supply Voltage VDD -0.3V to +7V Voltage at any pin -0.3V to Vcc +0.3V Power Dissipation at 25°C Plastic SSOP Ceramic DIP 1.5 W, derate10mW/°C 1.0 W, derate 7mW/°C DC Current Drain per pin ±10mA Storage Temperature Range: Operating Temperature Range: (Industrial) (Military) -65°C to +150°C -40°C to +85°C -55°C to +125°C NOTE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS VDD = 3.0 V to 5.5 V, GND = 0V, TA = Operating Temperature Range (unless otherwise specified). LIMITS PARAMETER Input Voltage Clock Input Voltage Input Leakage Current Output Voltage SYMBOL CONDITIONS MIN Input Voltage HI Input Voltage LO VIH VIL 70% VDD Input Voltage HI Input Voltage LO VIHC VILC VDD-0.5 Input Sink Input Source IIH IIL TYP MAX UNIT 30% VDD V V 0.5V V V 1.0 -1.0 µA µA 2.4 90% VDD V V Logic “1” Output Voltage VOH1 VOH2 VDD=5V±10%, IOH=-3mA VDD=3.3V±10%, IOH=-1mA Logic “0” Output Voltage VOL1 VOL2 VDD=5V±10%, IOL=1.8mA VDD=3.3V±10%, IOH=1mA 0.4 10% VDD V V IDDSB VIN=VDD, Outputs Open 2.0 mA Operating Supply Current IDD f=1MHz, Outputs Open 10.0 mA Input Capacitance CIN 7.0 pF COUT 10.0 pF Standby Supply Current Output Capacitance HOLT INTEGRATED CIRCUITS 7 HI-15530 AC ELECTRICAL CHARACTERISTICS VDD = 3.0V to 5.5V, GND = 0V, TA = Operating Temperature Range, CL=50pF PARAMETER SYMBOL LIMITS MIN TYP MAX UNITS Encoder Timing Encoder Clock Frequency fEC 0 15 MHz Send Clock Frequency fESC 0 2.5 MHz Encoder Clock Rise Time tECR 8 ns Encoder Clock Fall Time tECF 8 ns 1.25 MHz Encoder Data Rate fED 0 Master Reset Pulse Width tMR 150 Shift Clock Delay tE1 Serial Data Setup Time tE2 ns 125 75 ns ns Serial Data Hold Time tE3 75 ns Enable Setup Time tE4 90 ns Enable Pulse Width tE5 80 ns Sync Setup Time tE6 55 ns Sync Pulse Width tE7 150 Send Data Delay tE8 0 Bipolar Output Delay tE9 Enable Hold Time tE10 10 ns Sync Hold Time tE11 95 ns Decoder Clock Frequency fDC 0 15 MHz Decoder Clock Rise Time tDCR 8 ns Decoder Clock Fall Time tDCF 8 ns 1.25 MHz ns 50 ns 130 ns Decoder Timing Decoder Data Rate fDD 0 Decoder Reset Pulse Width tDR 150 Decoder Reset Setup Time tDRS 75 ns Decoder Reset Hold Time tDRH 10 ns Master Reset Pulse Width tMR 150 ns Bipolar Data Pulse Width tD1 tDC+10 Sync Transition Span tD2 One-Zero Overlap tD3 Short Data Transition Span tD4 6tDC Long Data Transition Span tD5 12tDC Sync Delay (On) tD6 -20 110 ns Take Data Delay (On) tD7 0 110 ns Serial Data Out Delay tD8 80 ns Sync Delay (Off) tD9 0 110 ns Take Data Delay (Off) tD10 0 110 ns Valid Word Delay tD11 0 110 ns HOLT INTEGRATED CIRCUITS 8 ns ns 18tDC ns tDC-10 ns ns ns HI-15530 SERIAL DATA OUT TAKE DATA ENCODER SHIFT CLK VALID WORD VDD ENCODER CLK SEND CLK IN ADDITIONAL PIN CONFIGURATIONS (See page 3-35 for 24-Pin Small Outline SSOP) 4 DECODER CLK N/C N/C BIPOLAR ZERO IN BIPOLAR ONE IN UNIPOLAR DATA IN DECODER SHIFT CLOCK 3 2 1 28 27 26 5 25 6 24 7 8 9 HI-15530CLI HI-15530CLT HI-15530CLM 13 MASTER RESET 24 - Pin Ceramic Side-Brazed DIP 23 22 21 10 20 11 19 12 13 14 15 16 17 18 ¸ 6 OUT VDD ENCODER CLK SEND CLK IN SEND DATA SYNC SELECT ENCODER ENABLE SERIAL DATA IN BIPOLAR ONE OUT OUTPUT INHIBIT BIPOLAR ZERO OUT ¸ 6 OUT BIPOLAR ZERO OUT OUTPUT INHIBIT HI-15530CDI HI-15530CDT HI-15530CDM 24 23 22 21 20 19 18 17 16 15 14 COMMAND / DATA SYNC DECODER RESET GND MASTER RESET VALID WORD 1 ENCODER SHIFT CLK 2 TAKE DATA 3 SERIAL DATA OUT 4 DECODER CLK 5 BIPOLAR ZERO IN 6 BIPOLAR ONE IN 7 UNIPOLAR DATA IN 8 DECODER SHIFT CLK 9 COMMAND / DATA SYNC 10 DECODER RESET 11 GND 12 28 - Pin Ceramic LCC ORDERING INFORMATION HI - 15530PS x x (Plastic) PART NUMBER Blank F LEAD FINISH Tin / Lead (Sn / Pb) Solder 100% Matte Tin (Pb-free, RoHS compliant) PART NUMBER TEMPERATURE RANGE FLOW BURN IN I -40°C TO +85°C I NO T -55°C TO +125°C T NO M -55°C TO +125°C M YES PART NUMBER PACKAGE DESCRIPTION 15530PS 24 PIN PLASTIC SSOP See next page for Ceramic package style Ordering Information HOLT INTEGRATED CIRCUITS 9 SEND DATA N/C N/C SYNC SELECT ENCODER ENABLE SERIAL DATA IN BIPOLAR ONE OUT HI-15530 ORDERING INFORMATION (cont.) HI - 15530Cx x (Ceramic) PART NUMBER TEMPERATURE RANGE FLOW BURN IN I -40°C TO +85°C I NO Gold (Pb-free, RoHS compliant) T -55°C TO +125°C T NO Gold (Pb-free, RoHS compliant) M -55°C TO +125°C M YES LEAD FINISH Tin / Lead (Sn / Pb) Solder PART NUMBER PACKAGE DESCRIPTION 15530CD 24 PIN CERAMIC SIDE BRAZED DIP 15530CL 28 PIN CERAMIC LEADLESS CHIP CARRIER HOLT INTEGRATED CIRCUITS 10 HI-15530 24-PIN PLASTIC SSOP Package Type: 24HS .323 ± .012 (8.20 ± .30) .006 TYP (.15) .209 ± .012 (5.30 ± .30) .307 ± .016 (7.80 ± .40) SEE DETAIL A .012 TYP (.30) .073 ± .0055 (1.86 ± .14) 0° to 8° .026 TYP (.65) .005 ± .001 (.13 ± .08) .030 ± .008 (.75 ± .20) DETAIL A 24-PIN CERAMIC SIDE-BRAZED DIP Package Type: 24C 1.220 MAX (30.988 MAX) .595 ±.010 (15.113 ±.254) .610 ±.010 (15.494 ±.254) .225 MAX (5.715 MAX) .050 TYP (1.270 TYP) .125 MIN (3.175 MIN) .018 TYP (.457 TYP) .085 ±.009 (2.159 ±.229) .100 BSC (2.540 BSC) HOLT INTEGRATED CIRCUITS 11 .600 ±.010 (15.240 ±.254) .010 +.002/-.001 (.254 +.051/-.025) HI-15530 28-PIN CERAMIC LEADLESS CHIP CARRIER Package Type: 28S .020 INDEX (.508 INDEX) .080 ± .020 (2.032 ± .508) PIN 1 PIN 1 .050 ± .005 (1.270 ± .127) .451 ± .009 (11.455 ± .229) SQ. .050 BSC (1.270 BSC) .008R ± .006 (.203R ± .152) .040 x 45° 3PLS (1.016 x 45° 3PLS) HOLT INTEGRATED CIRCUITS 12 .025 ± .003 (.635 ± .076)