AC Film Capacitors Lighting B 32436 Construction Dielectric: polypropylene film Aluminium can Soft polyurethan resin Internal dischage resistor Overpressure disconnector Features Self-healing properties Low dissipation factor High insulation resisitance Typical applications For general sine wave applications, mainly as series and parallel connection lighting capacitors. Terminals Single tag 2,8 mm ; Push-in terminals Mounting parts Metal stud (max. torque = 5 Nm) Technical data and specifications Standard IEC /EN 61048/61049 Rated capacitance CN 3 .. 60 µF Tolerance ± 5%, ±10% Rated voltage UN 250 ... 450 Vac Rated frequency fN 50...60Hz Life expectance 10 years Maximum ratings Maximum permissible voltage Umax 1,1 x UN (UN: rated voltage) Maximum permissible current Imax 1,3 x IN (IN : rated current) Test data AC test voltage terminal to terminal UTT 2,0 x UN , 60 s Insulation voltage terminals to case 2000 Vac, 60 s. Insulation resistance Ris or time constant τ at 20 °C 3000 s Rel. Humidity ≤ 65 °C (minimum value) Dissipation factor tanδ at 20 °C ≤ 1,0 x10-3 (120 Hz) Maximum rate of voltage rise du/dtmax 10 V/µs Issue No. 2 07/01 Page 1 of 5 AC Film Capacitors Lighting B 32436 Technical data (cont`d) Climatic data Climatic category 25/085/21 in accordance with IEC 60068-1 Lower category Tmin -25 °C Upper category Tmax +85 °C Damp heat test ttest 21 days Permitted capacitance ∆C/C ≤3% Note : 1) It should be noted that presence of harmonics produces over voltage & over current on capacitors. Resonance may cause serious damage to installation if a siginificant level of total harmonic distortion level exists for voltage or current. In such cases, series reactors must be considered. 2) Operating temperature class: In accordance with the reference standards, these temperatures are those measured on the surface on the capacitor Issue No. 2 07/01 Page 2 of 5 AC Film Capacitors Lighting B 32436 Dimensional drawings Issue No. 2 07/01 Page 3 of 5 AC Film Capacitors Lighting B 32436 Ordering codes and packing units 250 450 UN CN Max. dimensions Vac µF d x l (mm) Ordering code Packing unit (pcs.) B32436- 2 30 x 68 A1205-+0*0 112 3 30 x 68 A1305-+0*0 112 4 30 x 68 A1405-+0*0 112 5 30 x 68 A1505-+0*0 112 7 30 x 68 A1705-+0*0 112 8 30 x 68 A1805-+0*0 112 10 35 x 68 A1106-+0*0 84 12 35 x 68 A1126-+0*0 84 15 35 x 78 A1156-+0*0 84 16 35 x 78 A1166-+0*0 84 20 35 x 78 A1206-+0*0 84 25 40 x 78 A1256-+0*0 45 30 40 x 78 A1306-+0*0 45 35 40 x 103 A1356-+0*0 45 40 40 x 103 A1406-+0*0 45 45 40 x 103 A1456-+0*0 45 50 45 x 103 A1506-+0*0 45 60 45 x 103 A1606-+0*0 45 2 30 X 68 A6205-+0*0 112 3 30 x 68 A6305-+0*0 112 4 30 X 68 A6405-+0*0 112 5 30 x 78 A6505-+0*0 112 6 30 x 78 A6605-+0*0 112 8 35 x 78 A6805-+0*0 84 10 35 x 78 A6106-+0*0 84 Notes for ordering code: 1) Replace * for terminals 3- Aluminum can with push-in 4- Aluminum can with push-in terminals and bolt 5- Aluminum can with solder tag 6- Aluminum can solder tag without resistor 7- Aluminum can solder tag with bolt 8- Aluminium can solder tag, bolt, and without resistor M 8 fixing threaded bolt for ≤ φ 53mm. Note- Push-in terminal available only upto 30µf in 250 V. 2) Replace + for capacitance tolerance: - J- ± 5%, K- ± 10% Issue No. 2 07/01 Page 4 of 5 AC Film Capacitors Lighting B 32436 EPCOS AG 2000. All Rights Reserved. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. The information contained in this data sheet describes the type of component and shall not be considered as guaranteed characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed. Issue No. 2 07/01 Page 5 of 5