NEW PRODUCT NEW PRODUCT NEW PRODUCT GIB2401 THRU GIB2404 GLASS PASSIVATED PLASTIC RECTIFIER Reverse Voltage - 50 to 200 Volts Forward Current - 16.0 Amperes TO-263AB FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Dual rectifier construction, positive centertap ♦ Glass passivated chip junctions ♦ Low power loss ♦ High surge capability ♦ Superfast recovery times for high efficiency ♦ High temperature soldering in accordance with CECC 802 / Reflow guaranteed 0.160 (4.06) 0.190 (4.83) 0.380 (9.65) 0.420 (10.67) 0.045 (1.14) 0.245 (6.22) MIN 0.055 (1.40) K 0.047 (1.19) 0.055 (1.40) 0.320 (8.13) 0.575 (14.60) 0.360 (9.14) 1 SEATING PLATE K 0.625 (15.88) 2 0.090 (2.29) 0.110 (2.79) -T- 0.018 (0.46) 0.095 (2.41) 0.025 (0.64) 0.100 (2.54) 0.080 (2.03) 0.027 (0.686) MECHANICAL DATA 0.110 (2.79) 0.037 (0.940) Case: JEDEC TO-263AB molded plastic body Terminals: Plated lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.08 ounce, 2.24 grams PIN 1 K - HEATSINK PIN 2 Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS .Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GIB2401 GIB2402 GIB2403 GIB2404 UNITS Maximum recurrent peak reverse voltage VRRM 50 100 150 200 Volts Maximum RMS voltage VRMS 35 70 105 140 Volts Maximum DC blocking voltage VDC 50 100 150 200 Volts Maximum average forward rectified current at TC=125°C I(AV) 16.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TC=125°C IFSM 125.0 Amps VF 0.975 0.900 0.800 0.895 Volts IR 50.0 150.0 Maximum reverse recovery time per leg (NOTE1) trr 35.0 ns Typical junction capacitance per leg (NOTE 2) CJ 85.0 pF RΘJC 2.2 °C/W TJ, TSTG -65 to +150 °C Maximum instantaneous forward voltage per leg at: IF=4A, TJ=25°C IF=8A, TJ=25°C IF=4A, TJ=100°C IF=8A, TJ=100°C Maximum DC reverse current at rated DC blocking voltage TC=25°C TC=100°C Typical thermal resistance (NOTE 3) Operating junction and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to case per leg mounted on heatsink 4/98 5.0 500.0 µA RATINGS AND CHARACTERISTICS CURVES GIB2401 THRU GIB2404 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 20 RESISTIVE OR INDUCTIVE LOAD INFINITE HEAT SINK, TC 16 12 8.0 AMBIENT AIR RATING, TA 4.0 0 0 50 100 150 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT, AMPERES FIG. 1 -FORWARD CURRENT DERATING CURVE 150 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) TC=125°C 125 100 75 50 25 0 1 TEMPERATURE, °C 10 100 NUMBER OF CYCLES AT 60 HZ FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG FIG.3 -TYPICAL REVERSE CHARACTERISTICS PER LEG 100 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 80 TJ=125°C 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 0.01 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG JUNCTION CAPACITANCE, pF 1,000 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 100 10 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 10 °C 125 TJ= 00°C TJ=1 1 0.1 TJ=25°C 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, %