NC7SZ18 TinyLogic® UHS 1-of-2 Non-Inverting De-multiplexer with 3-STATE Deselected Output Features Description Ultra-High Speed: tPD 2.5ns Typical at 5V VCC High Impedance Output when Deselected Proprietary Noise/EMI Reduction Circuitry The NC7SZ18 is a 1-of-2 non-inverting demultiplexer. The device will buffer the data on the A pin and pass to either output Y0 or Y1 dependent on whether state of the select pin (S) is LOW or HIGH respectively. The deselected output will be placed into a high impedance state. The device is fabricated with advanced CMOS technology to achieve ultra high speed with high output drive while maintaining low static power dissipation over a broad VCC operating range. The device is specified to operate over the 1.65V to 5.5V VCC operating range. The inputs and outputs are high impedance when VCC is 0V. Inputs tolerate voltages up to 5.5V independent of VCC operating range. Broad VCC Operating Range: 1.65V to 5.50V Power Down High Impedance Inputs/Outputs Over-Voltage Tolerance Inputs Facilitate 5V to 3V Translation Ultra-Small MicroPak™ Packages Ordering Information Part Number Top Mark Package Packing Method NC7SZ18P6X Z18 6-Lead SC70, EIAJ SC88 1.25mm Wide 3000 Units on Tape & Reel NC7SZ18L6X D5 6-Lead MicroPak™, 1.00mm Wide 5000 Units on Tape & Reel NC7SZ18FHX D5 6-Lead, MicroPak2™, 1x1mm Body, .35mm Pitch 5000 Units on Tape & Reel ® TinyLogic is a registered trademark of Fairchild Semiconductor Corporation. MicroPak™ is a trademark of Fairchild Semiconductor Corporation. © 1999 Fairchild Semiconductor Corporation NC7SZ18 • Rev. 1.0.2 www.fairchildsemi.com NC7SZ18 — TinyLogic® UHS 1-of-2 Non-Inverting De-multiplexer with 3-STATE Deselected Output June 2011 Figure 1. SC70 (Top View) Figure 2. MicroPak™ (Top Through View) Figure 3. Pin 1 Orientation Notes: 1. AAA represents product code top mark (see Ordering Information). 2. Orientation of top mark determines pin one location. 3. Reading the top mark left to right, pin one is the lower left pin. Pin Definitions Pin # SC70 Pin # MicroPak™ Name Description 1 1 S 2 2 GND Data Input 3 3 A Demultiplexer Data 4 4 Y1 Output 5 5 VCC Supply Voltage 6 6 Y0 Output Ground Function Table Inputs Output S A Y0 Y1 L L L Z Z L H H H L Z L H H Z H NC7SZ18 — TinyLogic® UHS 1-of-2 Non-Inverting De-multiplexer with 3-STATE Deselected Output Pin Configurations H = HIGH Logic Level L = LOW Logic Level X = 3-STATE © 1999 Fairchild Semiconductor Corporation NC7SZ18 • Rev. 1.0.2 www.fairchildsemi.com 2 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit VCC Supply Voltage -0.5 7.0 V VIN DC Input Voltage -0.5 7.0 V VOUT 7.0 V IIK DC Input Diode Current VIN -0.5V -50 mA IOK DC Output Diode Current VIN -0.5V -50 mA IOUT DC Output Current ±50 mA ICC or IGND TSTG DC Output Voltage -0.5 DC VCC or Ground Current Storage Temperature Range -65 ±100 mA +150 °C TJ Junction Temperature Under Bias +150 °C TL Junction Lead Temperature (Soldering, 10 Seconds) +260 °C PD Power Dissipation at +85°C ESD SC70-6 180 MicroPak™-6 130 MicroPak2™-6 120 Human Body Model, JEDEC:JESD22-A114 4000 Charge Device Model, JEDEC:JESD22-C101 2000 mW V Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol VCC VIN VOUT tr, tf TA JA Parameter Min. Max. Supply Voltage Operating 1.65 5.50 Supply Voltage Data Retention 1.5 5.5 Input Voltage 0 5.5 V Output Voltage 0 VCC V VCC at 1.8V, ±0.15V, 2.5V ± 0.2V 0 20 VCC at 3.3V ± 0.3V 0 10 VCC at 5.0V ± 0.5V 0 5 -40 +85 Input Rise and Fall Times Conditions Operating Temperature Thermal Resistance © 1999 Fairchild Semiconductor Corporation NC7SZ18 • Rev. 1.0.2 SC70-6 425 MicroPak™-6 500 MicroPak2™-6 560 Unit V ns/V °C °C/W NC7SZ18 — TinyLogic® UHS 1-of-2 Non-Inverting De-multiplexer with 3-STATE Deselected Output Absolute Maximum Ratings www.fairchildsemi.com 3 Symbol Parameter VCC TA=-40 to +85°C TA=+25°C Condition Min. Typ. Max. Min. Unit Max. VIH HIGH Level Input Voltage 1.65 to 1.95 0.75VCC 0.75VCC 2.30 to 5.50 0.70VCC 0.70VCC VIL LOW Level Input Voltage 1.65 to 1.95 0.25VCC 0.25VCC 2.30 to 5.50 0.30VCC 0.30VCC 1.65 1.55 1.65 1.55 2.30 VIN=VIH, IOH=-100µA 2.20 2.30 2.20 2.90 3.00 2.90 4.40 4.50 4.40 1.65 IOH=-4mA 1.29 1.52 1.29 2.30 IOH=-8mA 1.90 2.15 1.90 3.00 IOH=-16mA 2.40 2.80 2.40 3.00 IOH=-24mA 2.30 3.68 2.30 4.50 IOH=-32mA 3.80 4.20 3.80 3.00 4.50 VOH HIGH Level Output Voltage 1.65 2.30 3.00 VIN=VIL IOL=100µA 4.50 VOL LOW Level Output Voltage IIN Input Leakage Current IOZ V V V 0.00 0.10 0.10 0.00 0.10 0.10 0.00 0.10 0.10 0.00 0.10 0.10 1.65 IOL=4mA 0.08 0.24 0.24 2.30 IOL=8mA 0.10 0.30 0.30 3.00 IOL=16mA 0.15 0.40 0.40 3.00 IOL=24mA 0.22 0.55 0.55 4.50 IOL=32mA 0.22 0.55 0.55 V 0 to 5.5 VIN=5.5V, GND ±0.1 ±1.0 µA 3-STATE Output Leakage 1.65 to 5.50 VIN=VIL or VOH 0<VOUT 5.5V ±0.5 ±5.0 µA IOFF Power Off Leakage Current 0 1 10 µA ICC Quiescent Supply Current 1 10 µA © 1999 Fairchild Semiconductor Corporation NC7SZ18 • Rev. 1.0.2 VIN or VOUT=5.5V 1.65 to 5.50 VIN=5.5V, GND NC7SZ18 — TinyLogic® UHS 1-of-2 Non-Inverting De-multiplexer with 3-STATE Deselected Output DC Electrical Characteristics www.fairchildsemi.com 4 Symbol Parameter VCC Condition Min. Min. Max. 2.0 6.3 10.1 2.0 10.5 1.0 3.6 5.7 1.0 6.0 0.8 2.7 4.0 0.8 4.3 0.5 2.0 3.1 0.5 3.3 3.30 ± 0.30 CL=50pF, RD=500 5.00 ± 0.50 V =OPEN 1 1.2 3.4 4.9 1.2 5.4 2.5 3.9 0.8 4.2 Output Enable Time tPZL, tPHZ Output Disable Time CIN Typ. Max. 2.50 ± 0.20 CL=15pF, RD=1M 3.30 ± 0.30 V =OPEN 1 Propagation Delay 5.00 ± 0.50 A to Y0 or Y1 1.80 ± 0.15 tPLH, tPHL TA=-40 to +85°C TA=+25°C 0.8 1.80 ± 0.15 CL=50pF, 2.50 ± 0.20 RD,RU=500 V1=GND for 3.30 ± 0.30 tPZH V1=VIN for 5.00 ± 0.50 tPZL VIN=2 x VCC 1.80 ± 0.15 CL=50pF, 2.50 ± 0.20 RD,RU=500 V1=GND for 3.30 ± 0.30 tPHZ V1=VIN for 5.00 ± 0.50 tPLZ VIN=2 x VCC 3.0 6.9 12.0 3.0 12.5 1.8 4.2 6.8 1.8 7.3 1.2 3.2 5.0 1.2 5.5 0.8 2.5 4.0 0.8 4.3 2.5 6.0 10.0 2.5 10.5 1.5 4.0 6.8 1.5 7.1 0.8 2.9 4.9 0.8 5.3 0.3 1.8 3.5 0.3 3.7 Unit Figure ns Figure 4 Figure 6 ns Figure 4 Figure 6 ns Figure 4 Figure 6 Input Capacitance 0 2.5 pF COUT Output Capacitance 0 4.0 pF CPD Power Dissipation Capacitance(4) 3.30 16.0 5.00 19.5 pF Figure 5 Note: 4. CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at no output loading and operating at 50% duty cycle. CPD is related to ICCD dynamic operating current by the expression: ICCD=(CPD)(VCC)(fIN)+(ICCstatic). © 1999 Fairchild Semiconductor Corporation NC7SZ18 • Rev. 1.0.2 NC7SZ18 — TinyLogic® UHS 1-of-2 Non-Inverting De-multiplexer with 3-STATE Deselected Output AC Electrical Characteristics www.fairchildsemi.com 5 Notes: 5. CL includes load and stray capacitance. 6. Input PRR = 1.0MHz, tW = 500ns. Figure 5. ICCD Test Circuit Figure 4. AC Test Circuit Figure 6. AC Waveforms © 1999 Fairchild Semiconductor Corporation NC7SZ18 • Rev. 1.0.2 NC7SZ18 — TinyLogic® UHS 1-of-2 Non-Inverting De-multiplexer with 3-STATE Deselected Output AC Loadings and Waveforms www.fairchildsemi.com 6 SYMM C L 2.00±0.20 0.65 A 0.50 MIN 6 4 B PIN ONE 1.25±0.10 1 1.90 3 0.30 0.15 (0.25) 0.40 MIN 0.10 0.65 A B 1.30 LAND PATTERN RECOMMENDATION 1.30 1.00 0.80 SEE DETAIL A 1.10 0.80 0.10 C 0.10 0.00 C 2.10±0.30 SEATING PLANE NOTES: UNLESS OTHERWISE SPECIFIED GAGE PLANE (R0.10) 0.25 0.10 0.20 A) THIS PACKAGE CONFORMS TO EIAJ SC-88, 1996. B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE BURRS OR MOLD FLASH. D) DRAWING FILENAME: MKT-MAA06AREV6 30° 0° 0.46 0.26 DETAIL A SCALE: 60X Figure 7. 6-Lead, SC70, EIAJ SC88, 1.25mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. Tape and Reel Specification NC7SZ18 — TinyLogic® UHS 1-of-2 Non-Inverting De-multiplexer with 3-STATE Deselected Output Physical Dimensions Please visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/products/analog/pdf/sc70-6_tr.pdf. Package Designator P6X © 1999 Fairchild Semiconductor Corporation NC7SZ18 • Rev. 1.0.2 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 3000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 7 2X 0.05 C 1.45 B 2X (1) 0.05 C (0.254) (0.49) 5X 1.00 (0.75) PIN 1 IDENTIFIER 5 (0.52) 1X A TOP VIEW 0.55MAX (0.30) 6X PIN 1 0.05 C 0.05 0.00 RECOMMENED LAND PATTERN 0.05 C C 1.0 DETAIL A 0.10 0.05 0.45 0.35 0.10 0.00 6X 0.25 0.15 6X C B A C 0.40 0.30 0.35 5X 0.25 0.40 5X 0.30 0.5 (0.05) 6X BOTTOM VIEW DETAIL A PIN 1 TERMINAL 0.075 X 45 CHAMFER (0.13) 4X Notes: 1. CONFORMS TO JEDEC STANDARD M0-252 VARIATION UAAD 2. DIMENSIONS ARE IN MILLIMETERS 3. DRAWING CONFORMS TO ASME Y14.5M-1994 4. FILENAME AND REVISION: MAC06AREV4 5. PIN ONE IDENTIFIER IS 2X LENGTH OF ANY OTHER LINE IN THE MARK CODE LAYOUT. Figure 8. 6-Lead, MicroPak™, 1.0mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. NC7SZ18 — TinyLogic® UHS 1-of-2 Non-Inverting De-multiplexer with 3-STATE Deselected Output Physical Dimensions Tape and Reel Specification Please visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/products/logic/pdf/micropak_tr.pdf. Package Designator L6X © 1999 Fairchild Semiconductor Corporation NC7SZ18 • Rev. 1.0.2 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 8 0.89 0.35 0.05 C 1.00 2X B A 5X 0.40 PIN 1 MIN 250uM 0.66 1.00 1X 0.45 6X 0.19 0.05 C TOP VIEW RECOMMENDED LAND PATTERN FOR SPACE CONSTRAINED PCB 2X 0.90 0.05 C 0.35 0.55MAX C 5X 0.52 SIDE VIEW 0.73 (0.08) 4X 1 DETAIL A 2 1X 0.57 0.09 0.19 6X 3 0.20 6X ALTERNATIVE LAND PATTERN FOR UNIVERSAL APPLICATION (0.05) 6X 5X 0.35 0.25 6 5 4 0.35 0.60 (0.08) 4X 0.10 .05 C C B A 0.40 0.30 BOTTOM VIEW NOTES: A. COMPLIES TO JEDEC MO-252 STANDARD B. DIMENSIONS ARE IN MILLIMETERS. C. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994 D. LANDPATTERN RECOMMENDATION IS BASED ON FSC DESIGN. E. DRAWING FILENAME AND REVISION: MGF06AREV3 Figure 9. 0.075X45° CHAMFER DETAIL A PIN 1 LEAD SCALE: 2X 6-Lead, MicroPak2™, 1x1mm Body, .35mm Pitch Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. NC7SZ18 — TinyLogic® UHS 1-of-2 Non-Inverting De-multiplexer with 3-STATE Deselected Output Physical Dimensions Tape and Reel Specification Please visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/packaging/MicroPAK2_6L_tr.pdf. Package Designator FHX © 1999 Fairchild Semiconductor Corporation NC7SZ18 • Rev. 1.0.2 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 9 NC7SZ18 — TinyLogic® UHS 1-of-2 Non-Inverting De-multiplexer with 3-STATE Deselected Output 10 www.fairchildsemi.com © 1999 Fairchild Semiconductor Corporation NC7SZ18 • Rev. 1.0.2