ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Low Power, 5-MBd Digital CMOS Optocoupler Data Sheet Description Features Broadcom® ACPL-M21L (single-channel SO-5 package), ACPL-021L (single-channel SO-8 package), ACPL-024L (dual-channel SO-8 package), ACPL-W21L (single-channel stretched SO-6 package), and ACPL-K24L (dual-channel stretched SO-8 package) are optically coupled logic gates. The detector IC has CMOS output stage and optical receiver input stage with built-in Schmitt trigger to provide logic-compatible waveforms, eliminating the requirement for additional waveshaping. An internal shield on the ACPL-M21L/021L/024L/W21L/K24L guarantees common mode transient immunity of 25 kV/μs at a common-mode voltage of 1000V. The ACPL-x2xL optocouplers' series operates from a 2.7V to 5.5V supply with guaranteed AC and DC performance from an extended temperature range of –40°C to +105°C. CAUTION Take normal static precautions in handling and assembly of this component to prevent damage and/or degradation that might be induced by electrostatic discharge (ESD). The components featured in this data sheet are not to be used in military or aerospace applications or environments. CMOS output Wide supply voltage: 2.7V to 5.5V Low power supply current IDD: 1.1 mA/channel max. Low forward current IF: 1.6 mA min. Speed: 5 MBd typ. Pulse width distortion (PWD): 200 ns max. Propagation delay skew (tpsk): 220 ns max. Propagation delay (tp): 250 ns max. Common mode rejection: 25 kV/μs min. at VCM = 1000V Hysteresis: 0.2 mA typ Temperature range: –40°C to +105°C Safety and regulatory approvals — UL 1577 recognized: 3750 VRMS for 1 minute for ACPL-M21L/021L/024L and 5000 VRMS for 1 minute for ACPL-W21L/K24L — CSA Approval — IEC/EN 60747-5-5, Approval for Reinforced Insulation Applications Broadcom -1- Low isolation of high speed logic systems Computer peripheral interface Microprocessor system interface Ground loop elimination Pulse transformer replacement High-speed line receiver Power control systems ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Figure 1 Functional Diagram Anode Cathode 1 3 Shield 6 VDD 5 VO 4 GND Anode 1 6 VDD NC 2 5 VO Cathode 3 4 GND ACPL-W21L ACPL-M21L Anode1 1 8 VDD VO Cathode1 2 7 V01 6 NC Cathode2 3 6 V02 5 GND Anode2 4 5 GND NC 1 8 VDD Anode 2 7 Cathode 3 NC 4 Shield Shield ACPL-021L Shield ACPL-024L/K24L Table 1 Truth Table LED VO ON HIGH OFF LOW NOTE A 0.1 μF bypass capacitor must be connected between pins Vdd and GND. Broadcom -2- ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Ordering Information ACPL-M21L, ACPL-024L, and ACPL-021L are UL Recognized with 3750 VRMS for 1 minute per UL1577. ACPL-W21L and ACPL-K24L are UL Recognized with 5000 VRMS for 1 minute per UL1577. Table 2 Ordering Information Option Part Number ACPL-M21L ACPL-024L ACPL-021L ACPL-W21L ACPL-K24L RoHS Compliant -000E Package SO-5 UL1577 5000 Surface Mount Tape and Reel VRMS /1 Minute Rating X X -500E X X -560E X X SO-8 X -500E X X -560E X X X -500E X X -560E X X X X X X X X -500E X X X -560E X X X Stretched SO8 1500 per reel 100 per tube 1500 per reel -060E -000E 100 per tube 100 per tube X Stretched SO6 1500 per reel 1500 per reel X -060E -000E X 100 per tube X SO-8 100 per tube 1500 per reel X -060E -000E Quantity 100 per tube -060E -000E IEC/EN 60747-5-5 X X -060E X X -500E X X X -560E X X X X 1500 per reel X 100 per tube 100 per tube 1000 per reel X 1000 per reel X 80 per tube 80 per tube 1000 per reel X 1000 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-M21L-500E to order product of SO-5 package in Tape and Reel packaging with RoHS compliant. Option data sheets are available. Contact your Avago sales representative or authorized distributor for information. Broadcom -3- ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Package Outline Drawings Figure 2 ACPL-M21L SO-5 Package LAND PATTERN RECOMMENDATION 0.33 (0.013) ROHS-COMPLIANCE INDICATOR 0.64 (0.025) 1.27 (0.05) PART NUMBER DATE CODE NNNN 4.4 ±0.1 (0.173 ±0.004) YYWW EEE 7.0 ±0.2 (0.276 ±0.008) 4.39 (0.17) 8.26 (0.325) Lot ID 1.80 (0.071) 0.4 ±0.05 (0.016 ±0.002) 2.54 (0.10) 3.6 ±0.1* (0.142 ±0.004) 2.5 ±0.1 (0.098 ±0.004) 0.102 ±0.102 (0.004 ±0.004) 0.15 ±0.025 (0.006 ±0.001) 7° MAX. 1.27 BSC (0.050) 0.71 MIN (0.028) MAX. LEAD COPLANARITY = 0.102 (0.004) Dimensions in millimeters (inches). Note: Foating Lead Protrusion is 0.15 mm (6 mils) max. Broadcom -4- ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Figure 3 ACPL-024L/021L SO-8 Package LAND PATTERN RECOMMENDATION 1.91 (0.075) 0.64 (0.025) ROHS-COMPLIANCE INDICATOR 8 7 5 5.994 ±0.203 (0.236 ±0.008) NNNN 3.937 ±0.127 (0.155 ±0.005) PIN ONE 6 PART NUMBER DATE CODE Lot ID YYWW EEE 1 2 3 0.406 ±0.076 (0.016 ±0.003) 3.95 (0.156) 4 1.270 BSC (0.050) 1.27 (0.5) 7° * 5.080 ±0.127 (0.200 ±0.005) 3.175 ±0.127 (0.125 ±0.005) 7.49 (0.295) 45° X 0.432 (0.017) 0 ~ 7° 0.228 ±0.025 (0.009 ±0.001) 1.524 (0.060) 5.207 ±0.254 (0.205 ±0.010) Dimensions in Millimeters (Inches). Note: Floating lead protrusion is 0.15 mm (6 mils) max. Lead coplanarity = 0.10 mm (0.004 inches) max. Option number 500 not marked. 0.305 MIN. (0.012) Broadcom -5- 0.203 ±0.102 (0.008 ±0.004) ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Figure 4 ACPL-W21L Stretched SO-6 Package TOTAL PACKAGE WIDTH (INCLUSIVE OF MOLD FLASH) 4.834 ±0.254 (0.190 ±0.010) LAND PATTERN RECOMMENDATION 1.27 (0.050) BSG 12.65 (0.498) 6 5 4 ROHS-COMPLIANCE INDICATOR 0.76 (0.030) NNNN YYWW EEE PART NUMBER DATE CODE Lot ID 1.91 (0.075) 1 2 3 0.381 ±0.127 (0.015 ±0.005) 7° +0.127 0 +0.005 0.268 –0.000 6.807 ( 0.45 (0.018) 7° ) 45° 3.180 ±0.127 (0.125 ±0.005) 0.20 ±0.10 (0.008 ±0.004) Dimensions in Millimeters (Inches). Lead coplanarity = 0.1 mm (0.004 inches). 1.590 ±0.127 (0.063 ±0.005) 0.750 ±0.250 (0.0295 ±0.010) 11.50 ±0.250 (0.453 ±0.010) Broadcom -6- ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Figure 5 ACPL-K24L Stretched SO-8 Package Width TOTAL PACKAGE WIDTH (INCLUSIVE OF MOLD FLASH) 6.100 ±0.250 (0.240 ±0.010) 8 7 6 LAND PATTERN RECOMMENDATION 5 PART NUMBER ROHS-COMPLIANCE INDICATOR DATE CODE NNNN 12.650 (0.5) Lot ID YYWW EEE 6.807 ±0.127 (0.268 ±0.005) 1.905 (0.1) 1 2 3 4 0.450 (0.018) 7° 1.590 ±0.127 (0.063 ±0.005) 7° 45° 3.180 ±0.127 (0.125 ±0.005) 0.381 ±0.13 (0.015 ±0.005) 1.270 (0.050) BSG 0.254 ±0.100 (0.010 ±0.004) 0.750 ±0.250 (0.0295 ±0.010) 11.5 ±0.250 (0.453 ±0.010) Dimensions in Millimeters (Inches). Lead coplanarity = 0.1 mm (0.004 inches). Solder Reflow Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used. Regulatory Information The ACPL-M21L/024L/021L/W21L/K24L is approved by the following organizations. UL Approval under UL 1577, component recognition program up to VISO = 3750 VRMS for ACPL-M21L/024L/021L and VISO = 5000 VRMS for ACPL-W21L/K24L. CSA Approval under CSA Component Acceptance Notice #5. IEC/EN 60747-5-5 (Option 060 and 560 only). Broadcom -7- ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Table 3 Insulation and Safety Related Specifications Parameter Symbol ACPL-M21L ACPL-024L ACPL-021L ACPL-W21 ACPL-K24L Units Conditions Minimum External Air Gap (Clearance) L(101) 5 4.9 8 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (Creepage) L(102) 5 4.8 8 mm Measured from input terminals to output terminals, shortest distance path along body. 0.08 0.08 0.08 mm Through insulation distance conductor to conductor, usually the straight line distance thickness between the emitter and detector. 175 175 175 V DIN IEC 112/VDE 0303 Part 1 IIIa IIIa IIIa Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) CTI Isolation Group Material Group (DIN VDE 0110, 1/89, Table 1) Table 4 IEC/EN60747-5-5 Insulation Characteristicsa (Option 060 and 560 Only) Characteristic Description Symbol ACPL-M21L/ 024L/021L Unit ACPL-W21L/ K24L Installation classification per DIN VDE 0110/39, Table 1 for rated mains voltage ≤ 150 Vrms for rated mains voltage ≤ 300 Vrms for rated mains voltage ≤ 600 Vrms for rated mains voltage ≤ 1000 Vrms I – IV I – III I – II I – IV I – IV I – III I – III Climatic Classification 55/105/21 55/105/21 Pollution Degree (DIN VDE 0110/39) 2 2 Maximum Working Insulation Voltage VIORM 567 1140 Vpeak Input to Output Test Voltage, Method ba VPR 1063 2137 Vpeak Input to Output Test Voltage, Method aa VIORM × 1.6 = VPR, Type and Sample Test, tm = 10 sec, Partial discharge < 5 pC VPR 896 1824 Vpeak Highest Allowable Overvoltage (Transient Overvoltage tini = 60 sec) VIOTM 6000 8000 Vpeak Safety-limiting values – maximum values allowed in the event of a failure. Case Temperature Input Currentb Output Powerb TS 150 IS, INPUT 150 PS, OUTPUT 600 175 230 600 °C mA mW Insulation Resistance at TS, VIO = 500 V RS >109 VIORM × 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial discharge < 5 pC >109 a. Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC/EN 60747-5-5) for a detailed description of Method a and Method b partial discharge test profiles. b. Refer to the following figure for dependence of PS and IS on ambient temperature. NOTE These optocouplers are suitable for "safe electrical isolation" only within the safety limit data. Maintenance of the safety limit data shall be ensured by means of protective circuits. Broadcom -8- ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Table 5 Absolute Maximum Ratings Parameter Symbol Min. Max. Units Condition Storage Temperature TS –55 125 °C Operating Temperature TA –40 105 °C Reverse Input Voltage VR 5 V Supply Voltage VDD 6.5 V Average Forward Input Current IF 8 mA Peak Forward Input Current IF(TRAN) 1 A ≤1 μs pulse width, <300 pulses per second Output Current IO 10 mA At max VDD Output Voltage VO VDD +0.5 V Lead Solder Temperature TLS Solder Reflow Temperature Profile See Package Outline Drawings –0.5 260°C for 10 sec., 1.6 mm below seating plane Table 6 Recommended Operating Conditions Parameter Symbol Min. Max. Units Operating Temperature TA –40 105 °C Input Current, Low Level IFL 0 250 μA Input Current, High Level IFH 1.6a 6 mA Power Supply Voltage VDD 2.7 5.5 V Forward Input Voltage VF (OFF) 0.8 V a. The initial switching threshold is 1.6 mA or less. It is recommended that 2.2 mA be used to permit at least a 20% LED degradation guardband. Broadcom -9- ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Electrical Specifications (DC) Over recommended temperature (TA = –40°C to +105°C) and supply voltage (2.7V ≤ VDD ≤ 5.5V). All typical specifications are at VDD = 2.7V, TA = 25°C, unless otherwise specified. Table 7 Electrical Specifications (DC) Parameter Symbol Channel Min. Input Forward Voltage VF Input Reverse Breakdown Voltage BVR 8 Logic High Output Voltage VOH Logic Low Output Voltage ITH Logic Low Output Supply Current IDDL Logic High Output Supply Current Input Capacitance 1.5 IDDH Max. 2.0 Units Test Conditions V IF = 2.2 mA (Figure 6 and Figure 7) V IR = 10 μA VDD – 0.1 V IF = 2.2 mA, IO = –20 μA VDD – 1.0 V IF = 2.2 mA, IO = –3.2 mA (Figure 8) 11 VOL Input Threshold Current Typ. 0.001 0.1 V IF = 0 mA, IO = 20 μA 0.15 0.4 V IF = 0 mA, IO = 3.2 mA (Figure 9) 0.5 1.4 mA Figure 10 Single 0.6 1.1 mA Dual 1.2 2.2 VF = 0V, VDD = 5.5V, IO = Open (Figure 11) mA IF = 2.2 mA, VDD = 5.5V, IO = Open (Figure 12) 77 pF f = 1 MHz, VF = 0V –1.9 mV/°C IF = 2.2 mA Single 0.5 1.1 Dual 1.0 2.2 CIN Input Diode Temperature Coefficient VF/TA Broadcom - 10 - ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Switching Specifications (AC) Over recommended temperature (TA = –40°C to +105°C), supply voltage (2.7V ≤ VDD ≤ 5.5V). All typical specifications are at VDD = 2.7V, TA = 25°C. Table 8 Switching Specifications (AC) Parameter Symbol Min. Typ. Max. Units Test Conditions Propagation Delay Time to Logic Low tPHL Outputa 130 250 ns IF=2.2 mA, CL=15 pF (Figure 13, Figure 17), CMOS Signal Levels Propagation Delay Time to Logic High Outputa tPLH 115 250 ns IF=2.2 mA, CL=15 pF (Figure 14, Figure 17), CMOS Signal Levels Pulse Width Distortionb PWD 200 ns CMOS Signal Levels Propagation Delay Skewc tPSK 220 ns Output Rise Time (10% to 90%) tR 11 ns IF = 2.2 mA, CL= 15 pF, CMOS Signal Levels. Output Fall Time (90% to 10%) tF 11 ns IF = 2.2 mA, CL= 15 pF, CMOS Signal Levels. Static Common Mode Transient Immunity at Logic High Outputd |CMH| 25 40 kV/μs VCM = 1000V, TA = 25°C, IF = 2.2 mA, CL= 15 pF, VI = 5V, (RT = 1.6 k) or VI = 3.3V, (RT = 840 ), CMOS Signal Levels, Figure 18 Static Common Mode Transient Immunity at Logic Low Outpute |CML| 25 40 kV/μs VCM = 1000V, TA = 25°C, IF = 0 mA, CL= 15 pF, VI = 0V, (RT = 1.6 k) or (RT = 840), CMOS Signal Levels, Figure 18 a. tPHL propagation delay is measured from the 50% (Vin or IF) on the falling edge of the input pulse to the 50% VDD of the falling edge of the VO signal. tPLH propagation delay is measured from the 50% (Vin or IF) on the rising edge of the input pulse to the 50% level of the rising edge of the VO signal. b. PWD is defined as |tPHL – tPLH|. c. tPSK is equal to the magnitude of the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature within the recommended operating conditions. d. CMH is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state. e. CML is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a low logic state. NOTE Use of a 0.1 μF bypass capacitor connected between VDD and ground is recommended. Package Characteristics All typical at TA = 25°C. Table 9 Package Characteristics Parameter Symbol Input-Output Insulation VISO Input-Output Resistance RI-O Input-Output Capacitance CI-O Part Number Min. Typ. ACPL-M21L/024L/021L 3750 ACPL-W21L/K24L Max. Units Test Conditions Vrms RH < 50% for 1 min., TA = 25°C 1012 VI-O = 500 V 0.6 pF f = 1 MHz, TA = 25°C 5000 Broadcom - 11 - ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Figure 6 Forward Voltage vs. Temperature Figure 7 Forward Current vs. Forward Voltage 100 1.7 IF - FORWARD CURRENT (mA) VF - FORWARD VOLTAGE (V) 1.8 1.6 1.5 1.4 1.3 1.2 –40 0 20 40 60 TA - TEMPERATURE (°C) 80 0.1 1.3 100 1.5 1.6 VF - FORWARD VOLTAGE (V) 1.7 1.8 0.25 6 VOL - LOW LEVEL OUTPUT VOLTAGE (V) IO = –3.2 mA 5 4 3 2 1 0 1 2 3 4 5 VDD - SUPPLY VOLTAGE (V) 6 0.2 0.15 0.1 0.05 –20 0 20 40 60 TA - TEMPERATURE (°C) 80 100 Figure 11 Logic Low Output Supply Current vs. Temperature 0.7 0.9 IDDL - LOGIC LOW OUTPUT SUPPLY CURRENT (mA) ITH_3.3V ITH_5.0V 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 VDD = 3.3V VF = 0V IO = 3.2 mA 0 –40 7 Figure 10 Input Threshold Current vs. Temperature Ith - INPUT THRESHOLD CURRENT (mA) 1.4 Figure 9 Logic Low Output Voltage vs. Temperature 7 VOH - HIGH LEVEL OUTPUT VOLTAGE (V) 1 0.01 –20 Figure 8 Logic High Output Voltage vs. Supply Voltage 0 10 0.6 0.5 0.4 0.3 0.2 IDDL @ 3.3V IDDL @ 5.0V 0.1 0 –40 –20 0 20 40 60 TA - TEMPERATURE (°C) 80 100 –40 Broadcom - 12 - –20 0 20 40 60 TA - TEMPERATURE (°C) 80 100 ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Figure 12 Logic High Output Supply Current vs. Temperature Figure 13 Propagation Delay, tPHL vs. Temperature 0.6 Tp - PROPAGATION DELAY (ns) IDDH - LOGIC HIGH OUTPUT SUPPLY CURRENT (mA) 0.7 0.5 0.4 0.3 0.2 IDDH_3.3V IDDH_5.0V 0.1 0 –40 –20 0 20 40 60 TA - TEMPERATURE (°C) 80 100 150 140 130 120 110 100 90 80 70 60 50 –40 IF = 1.6 mA, 2.2 mA, and 6 mA VDD = 2.7V –20 0 20 40 60 TA - TEMPERATURE (°C) 80 100 TPLH - PROPAGATION DELAY (ns) Figure 14 Propagation Delay, tPLH vs. Temperature 150 140 130 120 110 100 90 80 70 60 VDD = 2.7V 50 –40 –20 IF = 1.6 mA IF = 2.2 mA IF = 6.0 mA 0 20 40 60 TA - TEMPERATURE (°C) 80 100 Figure 15 Output Voltage vs. Input Current @ Vdd = 3.3V Figure 16 Output Voltage vs. Input Current @ Vdd = 5V 6 4 5 Vo - OUTPUT VOLTAGE (V) Vo - OUTPUT VOLTAGE (V) 3.5 3 2.5 2 1.5 1 3 2 1 0.5 0 4 VDD = 5.0V VDD = 3.3V 0 0 0.0001 0.0002 0.0003 0.0004 0.0005 0.0006 0.0007 0.0008 IF - INPUT CURRENT (A) Broadcom - 13 - 0 0.0001 0.0002 0.0003 0.0004 0.0005 0.0006 0.0007 0.0008 IF - INPUT CURRENT (A) ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet Figure 17 Circuit for tPLH, tPHL, tr, tf PULSE GEN tr = tf = 11 ns f = 1.0 MHz 50% DUTY CYCLE OUTPUT VO MONITORING NODE Vdd ACPL-M21L IF PULSE GEN tr = tf = 11 ns f = 1.0 MHz 50% DUTY CYCLE ACPL-W21L IF 6 1 * 5 CL = 15 pF INPUT MONITORING NODE 3 Shield 4 PULSE GEN tr = tf = 11 ns f = 1.0 MHz 50% DUTY CYCLE IF INPUT MONITORING NODE 6 2 5 3 4 * Shield Rm PULSE GEN tr = tf = 11 ns f = 1.0 MHz 50% DUTY CYCLE OUTPUT VO MONITORING NODE Vdd Vdd ACPL-021L 8 2 7 4 6 Shield OUTPUT VO MONITORING NODE ACPL-024L/K24L 1 3 Rm 1 CL = 15 pF INPUT MONITORING NODE Rm OUTPUT VO MONITORING NODE Vdd IF * 1 8 2 7 3 6 * CL = 15 pF INPUT MONITORING NODE 5 Rm IF (ON) 50% IF (ON) 0 mA INPUT IF tPLH tPHL VOH 50% VOL OUTPUT VO * 0.1 μF BYPASS — SEE NOTE 6 above.[6] Broadcom - 14 - 4 Shield 5 CL = 15 pF ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L Data Sheet ACPL-M21L, ACPL-021L, ACPL-024L, ACPL-W21L, ACPL-K24L: VI = 3.3V: R1 = 510 ±1%, R2 = 330 ±1% VI = 5.0V: R1 = 1 k ±1%, R2 = 600 ±1% RT = R1 + R2 ≈ R1 / R2 ≈ 1.5 Figure 18 Recommended Printed Circuit Board Layout and Input Current Limiting Resistor Selection VI R1 IF 1 VDD 6 VI 1 Vo 4 GND2 3 GND1 1 4 VI R1 I F GND2 1 8 2 7 VDD R2 2 3 7 4 Vo GND1 C 6 5 NC GND2 GND2 VI R2 R1 IF ACPL-021L 3 NNNN YYWW R2 VDD 8 NNNN YYWW GND2 Vo ACPL-W21L ACPL-M21L VI C 5 R2 3 R1 IF VDD 6 NNNN YYWW NNNN YYWW C 5 R2 GND1 R1 IF 4 Broadcom - 15 - 6 5 ACPL-024L/K24L C = 0.1 μF Vo1 C Vo2 GND2 For product information and a complete list of distributors, please go to our web site: www.broadcom.com. Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, and the A logo are among the trademarks of Broadcom and/or its affiliates in the United States, certain other countries and/or the EU. Copyright © 2016–2017 by Broadcom. All Rights Reserved. The term "Broadcom" refers to Broadcom Limited and/or its subsidiaries. For more information, please visit www.broadcom.com. Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does not assume any liability arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. AV02-3462EN – March 10, 2017