DATASHEET ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 12-bit, 125kSPS Low-power ADCs with Single-ended and Differential Inputs and Multiple Input Channels The ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315 and ISL26319 family of sampling SAR-type ADCs feature excellent linearity over supply and temperature variations, and offer versions with 1-, 2-, 4- and 8-channel single-ended inputs, and 1-, 2- and 4-channel differential inputs. A proprietary input multiplexer and combination buffer amplifier reduces the input drive requirements, resulting in lower cost and reduced board space. Specified measurement accuracy is maintained with input signals up to VDD. Members of the ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315 and ISL26319 family of Low-Power ADCs offer pinout intercompatibility, differing only in the analog inputs, to support quick replication of proven layouts across multiple design platforms. The serial digital interface is SPI compatible and is easily interfaced to popular FPGAs and microcontrollers. Power consumption is limited to 11mW at a sampling rate of 125kSPS, and an operating current of just 8µA typical between conversions, when configured for Auto Power-down mode. The ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 feature up to 5kV Human Body Model ESD survivability and are available in the popular SOIC and TSSOP packages. Performance is specified for operation over the full industrial temperature range (-40°C to +125°C). VDD Features • Pin-compatible family allows easy design upgrades • Excellent differential non-linearity (0.7LSB max) • Low THD: -86dB (typ) • Simple SPI-compatible serial digital interface • Low 2.2mA operating current • Power-down current between conversions 8µA (typ) • +5.25V to +2.7V supply • Excellent ESD survivability: 5kV HBM, 350V MM, 2kV CDM Applications • Industrial process control • Energy measurement • Multichannel data acquisition systems • Pressure sensors • Flow controllers VREF BUFFER ANALOG INPUTS DIFFERENTIAL/ SINGLE-ENDED MUX FN7549 Rev 3.00 August 18, 2015 CNV ADC SPI SCLK SDO SDI OSC POR GND FIGURE 1. FUNCTIONAL BLOCK DIAGRAM FN7549 Rev 3.00 August 18, 2015 Page 1 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Application Block Diagram I2 C Bus RTC ANALOG SIGNAL INPUT MODULEs Pressure/Strain Gage Sensor VREF RS-485 Precision Amps Gain Amplifiers DCP +V Precision Amps Precision Amps -V -V RTC VREF POWER Voltage Supervisor & Sequencers V Temperature Sensor LDO’s DCP System Power Thermistor +V Precision Amps -V Thermocouple +V Precision Amps Active Filters V Precision Amps Filters -V ISO-Thermal Block LDO Switching Controller Switching Regulators -V +V Active -V Core & I/O Power Switching Regulator +V Precision Amps Master μC RS-485 μC ADC M U X Active Filters +V VREF RS-232 MUX and ADC Actuators +V Motors Control loops Buffer, Filters, Span Drivers +V Precision Amps Precision Amps -V -V M U X +V High Voltage Input Rail ~24V DAC VREF ANALOG SIGNAL OUTPUT MODULE Flow Sensor Single Ended Controller -V Loop Supply Gain Amplifiers Differential Pressure Transducer w/ ¥ Extractor +V Iout 4 -20mA Vin Active Filters Isolator +V Precision Amps Precision Amps -V -V Isolated Power Pin-Compatible Family RESOLUTION (Bits) SPEED (kHz) ANALOG INPUT INPUT CHANNELS ISL26310 12 125 Differential 1 ISL26311 12 125 Single-Ended 1 ISL26312 12 125 Differential 2 ISL26313 12 125 Single-Ended 2 ISL26314 12 125 Differential 4 ISL26315 12 125 Single-Ended 4 ISL26319 12 125 Single-Ended 8 ISL26320 12 250 Differential 1 ISL26321 12 250 Single-Ended 1 ISL26322 12 250 Differential 2 ISL26323 12 250 Single-Ended 2 ISL26324 12 250 Differential 4 ISL26325 12 250 Single-Ended 4 ISL26329 12 250 Single-Ended 8 MODEL FN7549 Rev 3.00 August 18, 2015 Page 2 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Ordering Information DESCRIPTION PART NUMBER (Notes 1, 2, 3) INPUT CHANNEL RESOLUTION SPEED INPUT PART S (Bits) (kHz) (SE/DIFF) MARKING TEMP. RANGE PACKAGE (°C) (RoHS Compliant) PKG DWG # ISL26310FBZ (No longer available, recommended replacement: ISL26320FBZ) 26310 FBZ 12 125 Diff 1 -40 to +125 8 Ld SOIC M8.15 ISL26311FBZ (No longer available, recommended replacement: ISL26321FBZ) 26311 FBZ 12 125 SE 1 -40 to +125 8 Ld SOIC M8.15 ISL26312FVZ 26312 FVZ 12 125 Diff 2 -40 to +125 16 Ld TSSOP M16.173 ISL26313FBZ 26313 FBZ 12 125 SE 2 -40 to +125 8 Ld SOIC M8.15 ISL26314FVZ 26314 FVZ 12 125 Diff 4 -40 to +125 16 Ld TSSOP M16.173 ISL26315FVZ 26315 FVZ 12 125 SE 4 -40 to +125 16 Ld TSSOP M16.173 ISL26319FVZ 26319 FVZ 12 125 SE 8 -40 to +125 16 Ld TSSOP M16.173 NOTES: 1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319. For more information on MSL please see techbrief TB363. FN7549 Rev 3.00 August 18, 2015 Page 3 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Pin Configurations ISL26311 (8 LD SOIC) TOP VIEW ISL26310 (8 LD SOIC) TOP VIEW 1 VDD GND 2 AIN+ 3 4 LO NO AIN- ER NG AV A E BL IL A OR SU O PP ED RT 8 CNV VDD 1 7 SCLK GND 2 6 SDO VREF 3 5 AIN0 SDI 4 L NO GE ON R AV A E BL IL A OR SU O PP ED RT 8 CNV 7 SCLK 6 SDO 5 SDI ISL26313 (8 LD SOIC) TOP VIEW VDD 1 8 CNV GND 2 7 SCLK AIN0 3 6 SDO AIN1 4 5 SDI ISL26314 (16 LD TSSOP) TOP VIEW ISL26312 (16 LD TSSOP) TOP VIEW VDD 1 16 CNV VDD 1 16 CNV GND 2 15 SC LK GND 2 15 SCLK VR EF 3 14 SD O VREF 3 14 SDO GND 4 13 SD I GND 4 13 SDI A IN 0+ 5 12 NC AIN0+ 5 12 AIN3+ A IN 0- 6 11 NC AIN0- 6 11 AIN3- A IN 1+ 7 10 NC AIN1+ 7 10 AIN2+ A IN 1- 8 9 NC AIN1- 8 9 AIN2- ISL26319 (16 LD TSSOP) TOP VIEW ISL26315 (16 LD TSSOP) TOP VIEW VDD 1 16 CNV VDD 1 16 CNV G ND 2 15 SCLK GND 2 15 SCLK VREF 3 14 SDO VREF 3 14 SDO G ND 4 13 SDI GND 4 13 SDI AIN0 5 12 AIN3 AIN0 5 12 AIN7 NC 6 11 NC AIN1 6 11 AIN6 AIN1 7 10 AIN2 AIN2 7 10 AIN5 NC 8 9 NC AIN3 8 9 AIN4 FN7549 Rev 3.00 August 18, 2015 Page 4 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Pin Descriptions PIN NUMBER PIN NAME ISL26310 ISL26311 ISL26312 ISL26313 ISL26314 ISL26315 ISL26319 DESCRIPTION VDD 1 1 1 1 1 1 1 GND 2 2 2, 4 2 2, 4 2, 4 2, 4 VREF - 3 3 - 3 3 3 Reference Voltage Input AIN0+ - - 5 - 5 - - Differential Analog Input, Positive AIN0- - - 6 - 6 - - Differential Analog Input, Negative AIN1+ - - 7 - 7 - - Differential Analog Input, Positive AIN1- - - 8 - 8 - - Differential Analog Input, Negative AIN2+ - - - - 10 - - Differential Analog Input, Positive AIN2- - - - - 9 - - Differential Analog Input, Negative AIN3+ - - - - 12 - - Differential Analog Input, Positive AIN3- - - - - 11 - - Differential Analog Input, Negative AIN0 - 4 - 3 - 5 5 Single-Ended Analog Input AIN1 - - - 4 - 7 6 Single-Ended Analog Input AIN2 - - - - - 10 7 Single-Ended Analog Input AIN3 - - - - - 12 8 Single-Ended Analog Input AIN4 - - - - - - 9 Single-Ended Analog Input AIN5 - - - - - - 10 Single-Ended Analog Input AIN6 - - - - - - 11 Single-Ended Analog Input AIN7 - - - - - - 12 Single-Ended Analog Input SDI 5 5 13 5 13 13 13 Serial Interface Data Input SDO 6 6 14 6 14 14 14 Serial Interface Data Output SCLK 7 7 15 7 15 15 15 Serial Interface Clock Input CNV 8 8 16 8 16 16 16 Conversion Control Input NC - - 9, 10, 11, 12 - - 6, 8, 9, 11 - No Connect AIN+ 3 - - - - - - Differential Analog Input, Positive AIN- 4 - - - - - - Differential Analog Input, Negative FN7549 Rev 3.00 August 18, 2015 Positive Supply Voltage Ground Page 5 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Absolute Maximum Ratings Thermal Information AIN+, AIN-, VREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3 to VDD + 0.3V Digital Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3 to VDD + 0.3V VDD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 6V GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3 to + 0.3V ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . . . . .5000V Machine Model (Per JESD22-A115). . . . . . . . . . . . . . . . . . . . . . . . . . 350V Charged Device Model (Per JESD22-C101) . . . . . . . . . . . . . . . . . . . . . . 2000V Latch-up (Tested per JESD-78B; Class 2, Level A). . . . . . . . . . . . . . . . . . . . . . . 100mA Thermal Resistance (Typical) JA (°C/W) JC (°C/W) 8 Ld SOIC (Notes 4, 5) . . . . . . . . . . . . . . . . . 98 48 16 Ld TSSOP (Notes 4, 5) . . . . . . . . . . . . . . 92 29 Maximum Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80mW Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +150°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.7V to +5.25V CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 5. For JC, the “case temp” location is taken at the package top center. Electrical Specifications VREF = VDD V, VDD = 2.7V to 5V, VCM = VDD/2, SCLK = 20MHz and TA = -40°C to +125°C (typical performance at +25°C), unless otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +125°C. SYMBOL PARAMETER TEST LEVEL OR NOTES MIN (Note 6) TYP MAX (Note 6) UNITS ANALOG INPUTS Number of Input Channels Input Voltage Range Common Mode Input Voltage Range ISL26310, ISL26311 1 ISL26312, ISL26313 2 ISL26314, ISL26315 4 ISL26319 8 Differential Inputs (AINX+ - AINX-) is -VREF (Min) and +VREF (Max) 0 VREF V AINX, Single-Ended Inputs 0 VREF V VREF/2 + 0.2 V Differential Inputs VREF/2 – 0.2 Average Input Current CIN Input Capacitance Channel-Channel Crosstalk fIN = 50kHz VIN = FS, other channels = 0V VREF/2 2.5 µA 4 pF -86 dB VOLTAGE REFERENCE VREFEX External Reference Input Voltage Range IREFIN CREFIN 2 2.5 VDD V Average Input Current 100 120 µA Effective Input Capacitance 10 pF DC ACCURACY DNL INL Resolution (No Missing Codes) 12 Bits Differential Nonlinearity Error -0.7 +0.7 LSB Integral Nonlinearity Error -0.7 +0.7 LSB Gain Error -6 6 LSB Gain Error Matching -2 2 LSB Offset Error -6 6 LSB Offset Error Matching -2 2 LSB FN7549 Rev 3.00 August 18, 2015 Page 6 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Electrical Specifications VREF = VDD V, VDD = 2.7V to 5V, VCM = VDD/2, SCLK = 20MHz and TA = -40°C to +125°C (typical performance at +25°C), unless otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +125°C. (Continued) SYMBOL PSRR PARAMETER TEST LEVEL OR NOTES MIN (Note 6) Power Supply Rejection Ratio TYP MAX (Note 6) UNITS 70 dB DYNAMIC PERFORMANCE SNR Signal-to-Noise Notes: VIN = FS - 0.1dB, fIN = 10kHz Differential Inputs 73.4 dB Single-Ended Inputs 73.4 dB SINAD Signal-to-Noise + Distortion Notes: VIN = FS - 0.1dB, fIN = 10kHz Differential Inputs 73.1 dB Single-Ended Inputs 73.1 dB THD Total Harmonic Distortion Notes: VIN = FS - 0.1dB, fIN = 10kHz Differential Inputs -86 dB Single-Ended Inputs -86 dB Spurious-free Dynamic Range Notes: VIN = FS - 0.1dB fIN = 20kHz 96 dB SFDR BW -3dB Input Bandwidth 2.5 MHz tAD Sampling Aperture Delay 12 ns tjit Sampling Aperture Jitter 25 ps POWER SUPPLY REQUIREMENTS VDD Supply Voltage IDD Supply Current PD Power Consumption IPD Istby 2.7 5.25 V 2.2 3 mA Normal Operation 11 15 mW Power-down Current Auto Power-Down Mode 8 50 µA Standby Mode Current Auto Sleep Mode 0.4 mA DIGITAL INPUTS VIH 0.7 VDD V 0.2 VDD VIL VOH IOH = -1mA VOL IOL = 1mA IIH, IIL Input Leakage Current VDD-0.4 V V -100 Serial Clock Frequency 0.2 VDD V 100 nA 20 MHz TIMING SPECIFICATIONS (Note 7) tSCLK SCLK Period (in RAC Mode) 50 tSCLK SCLK Period (in RSC, RDC Modes) 50 tDATA Safe Data Transfer Time After Conversion State Begins tCSB_SCLK CSB Falling Low to SCLK Rising Edge ns 200 ns 3.2 µs 40 ns tSDI_SU SDI Setup Time with Respect to Positive Edge of SCLK 10 ns tSDI_H SDI Hold Time with Respect to Positive Edge of SCLK 10 ns tSDO_V SDOUT Valid Time with Respect to Negative Edge of SCLK tSDOZ_D SDOUT to High Impedance State After CNV (Note 8) Rising Edge (or last SCLK falling edge) 25 85 ns ns tACQ Acquisition Time when Fully Powered Up 800 ns tACQ Acquisition Time in Auto Sleep Mode 2.1 µs FN7549 Rev 3.00 August 18, 2015 Page 7 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Electrical Specifications VREF = VDD V, VDD = 2.7V to 5V, VCM = VDD/2, SCLK = 20MHz and TA = -40°C to +125°C (typical performance at +25°C), unless otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +125°C. (Continued) SYMBOL tACQ PARAMETER TEST LEVEL OR NOTES MIN (Note 6) TYP MAX (Note 6) UNITS Acquisition time in Auto Power-Down Mode 150 µs tSCLKH SCLK High Time 20 ns tSCLKL SCLK Low Time 20 ns tCNV CNV Pulse Width 100 ns NOTES: 6. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. 7. The device may become nonresponsive if the minimum acquisition times are not met in their respective modes, requiring a power cycle to restore normal operation. 8. Transition time to high impedance state is dominated by RC loading on the SDOUT pin. Specified value is measured using equivalent loading shown in Figure 2. VDD RL 2k OUTPUT PIN CL 10pF FIGURE 2. EQUIVALENT LOAD CIRCUIT FOR DIGITAL OUTPUT TESTING FN7549 Rev 3.00 August 18, 2015 Page 8 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Typical Performance Characteristics 0.5 0.5 0.4 0.4 0.3 0.3 0.2 0.2 0.1 0.1 INL (LSBs) DNL (LSBs) TA = +25°C, VDD = 5V, VREF = 5V, fSAMPLE = 125kHz, fSCLK = 20MHz, unless otherwise specified. 0 -0.1 0 -0.1 -0.2 -0.2 -0.3 -0.3 -0.4 -0.4 -0.5 -2000 -1000 0 1000 -0.5 -2000 2000 -1000 0 FIGURE 3. DIFFERENTIAL NONLINEARITY (DNL) vs CODE 1.0 0.8 POSITIVE DNL 0.6 0.6 0.4 0.4 0.2 0.2 INL DNL 0.8 0.0 -0.2 -0.4 -0.4 -0.6 POSITIVE INL 0.0 -0.2 -0.6 NEGATIVE DNL -0.8 -20 0 20 40 60 80 100 NEGATIVE INL -0.8 -1.0 -40 120 -20 0 20 TEMPERATURE (°C) 0.0 80 100 120 2.7V -0.1 1.5 -0.2 1.0 OFFSET ERROR (LSB) GAIN ERROR (LSB) 60 FIGURE 6. INL DISTRIBUTION vs TEMPERATURE 2.0 0.5 2.7V 3.3V -0.5 -1.0 -20 0 20 5.25V -0.4 3.3V 5.0V 5.25V -0.5 -0.6 -0.7 40 60 -0.9 80 100 120 TEMPERATURE (°C) FIGURE 7. GAIN ERROR vs SUPPLY VOLTAGE AND TEMPERATURE FN7549 Rev 3.00 August 18, 2015 -0.3 -0.8 5.0V -1.5 -2.0 -40 40 TEMPERATURE (°C) FIGURE 5. DNL DISTRIBUTION vs TEMPERATURE 0.0 2000 FIGURE 4. INTEGRAL NONLINEARITY (INL) vs CODE 1.0 -1.0 -40 1000 CODE CODE -1.0 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (°C) FIGURE 8. OFFSET ERROR vs SUPPLY VOLTAGE AND TEMPERATURE Page 9 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Typical Performance Characteristics TA = +25°C, VDD = 5V, VREF = 5V, fSAMPLE = 125kHz, fSCLK = 20MHz, unless otherwise specified. (Continued) 25 4.0 3.5 SUPPLY CURRENT (mA) APERTURE DELAY (ns) 20 15 10 5 3.0 5.25V 5.0V 2.5 2.0 1.5 1.0 3.3V 2.7V 0.5 0 2.7 3.2 3.7 4.2 4.7 0.0 -40 5.2 -20 0 SUPPLY VOLTAGE FIGURE 9. APERTURE DELAY vs SUPPLY VOLTAGE 20 40 60 TEMPERATURE (°C) 80 100 120 FIGURE 10. SUPPLY CURRENT vs VOLTAGE AND TEMPERATURE 2.5 50 45 SHUTDOWN CURRENT (µA) SUPPLY CURRENT (mA) 2.0 1.5 NORMAL MODE AUTO POWER DOWN MODE 1.0 AUTO SLEEP MODE 0.5 40 35 5.25V 30 25 5.0V 20 15 3.3V 10 5 0.0 100 1k 10k SAMPLE RATE (Sps) 0 -40 100k FIGURE 11. SUPPLY CURRENT vs SAMPLING RATE (VDD = 5V) -20 0 20 40 60 TEMPERATURE (°C) 80 100 120 FIGURE 12. SHUTDOWN CURRENTS vs VOLTAGE AND TEMPERATURE -80 75 5.25V 5.0V 74 -82 73 -84 THD (dB) SNR/SINAD (dB) 2.7V 72 5.25V 5.0V -86 3.3V 2.7V -88 71 70 -40 2.7V -20 0 20 40 60 TEMPERATURE (°C) 80 100 120 FIGURE 13. SNR AND SINAD vs SUPPLY VOLTAGE AND TEMPERATURE FN7549 Rev 3.00 August 18, 2015 -90 -40 -20 0 20 40 60 TEMPERATURE (°C) 80 3.3V 100 FIGURE 14. THD vs SUPPLY VOLTAGE AND TEMPERATURE Page 10 of 23 120 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Typical Performance Characteristics TA = +25°C, VDD = 5V, VREF = 5V, fSAMPLE = 125kHz, fSCLK = 20MHz, unless otherwise specified. (Continued) 0 75 -10 SNR -20 -30 SINAD THD (dB) SNR/SINAD (dB) 70 65 -40 -50 -60 -70 60 -80 -90 55 100 1k 10k 100k INPUT FREQUENCY (Hz) -100 100 1M 1k FIGURE 15. SNR AND SINAD vs INPUT FREQUENCY 1M FIGURE 16. THD vs INPUT FREQUENCY 70,000 0 SNR: 72.93dB SINAD: 72.71dB THD: -85.84dB SFDR: 96.16dBc ENOB: 11.79 -20 -40 60,000 65,536 CODES 50,000 -60 HITS AMPLITUDE (dB) 10k 100k INPUT FREQUENCY (Hz) -80 40,000 30,000 -100 20,000 -120 10,000 -140 -160 0 10 20 30 40 FREQUENCY (kHz) 50 FIGURE 17. SINGLE-TONE FFT FN7549 Rev 3.00 August 18, 2015 60 70 0 0 CODES -3 -2 -1 0 CODES 0 1 2 3 CODE FIGURE 18. SHORTED INPUT HISTOGRAM Page 11 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Circuit Description The ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315 and ISL26319 families are of 12-bit ADCs are low-power Successive Approximation-type (SAR) ADCs with 1-, 2-, 4-, or 8-channels and a choice of single-ended or differential inputs. The high-impedance buffered input simplifies interfacing to sensors and external circuitry. The entire ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315 and ISL26319 families are follows the same base pinout and differs only in the analog input pins, allowing the user to replicate the basic board layout across multiple platforms with a minimum redesign effort. The simple serial digital interface is compatible with popular FPGAs and microcontrollers and allows direct conversion control by the CNV pin. Functional Description The ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315 and ISL26319 devices are SAR (Successive Approximation Register) analog-to-digital converters that use capacitor-based charge redistribution as their conversion method. These devices include an on-chip power-on reset (POR) circuit to initialize the internal digital logic when power is applied. An on-chip oscillator provides the master clock for the conversion logic. The CNV signal controls when the converter enters into its signal acquisition time (CNV = 0), and when it begins the conversion sequence after the signal has been captured (CNV = 1). The converters include a configuration register that can be accessed via the serial port. The configuration register has various bits to indicate which channel (where applicable) is selected, to activate the auto-power-down feature where the ADC is shut down between conversions, or to output the configuration register contents along with the data conversion word whenever a conversion word is read from the serial port. The serial port Buffer ACQ CNV VREF The ISL26311, ISL26313, ISL26315, and ISL26319 feature single-ended inputs with output coding in binary format (see Table 2). The size of one LSB in these devices is VREF/4096. Figure 22 illustrates the ideal transfer function for these devices. DAC CNV CS ACQ VCM ACQ COMPARATOR CNV ACQ AIN CNV SAR LOGIC CS Buffer ACQ CNV FIGURE 19. ARCHITECTURAL BLOCK DIAGRAM, DIFFERENTIAL INPUT FN7549 Rev 3.00 August 18, 2015 The ISL26310, ISL26312, and the ISL26314 feature differential inputs with output data coding in two's complement format (see Table 1). The size of one LSB in these devices is (2*VREF)/4096. Figure 21 illustrates the ideal transfer function for these devices. CS ACQ CNV VCM ACQ CNV COMPARATOR SAR LOGIC CS DAC ACQ AIN– ADC Transfer Function VREF DAC CNV AIN+ Figures 19 and 20 illustrate simplified representations of the converter analog section for differential and single-ended inputs, respectively. During the acquisition phase (CNV = 0) the input signal is presented to the Cs samples capacitors. To properly sample the signal, the CNV signal must remain low for the specified time. When CNV is taken high (CNV = 1), the switches that connect the sampling capacitors to the input are opened and the control logic begins the successive approximation sequence to convert the captured signal into a digital word. The conversion sequence timing is determined by the on-chip oscillator. DAC VREF supports three different modes of reading the conversion data. These will be discussed later in this data sheet. FIGURE 20. ARCHITECTURAL BLOCK DIAGRAM, SINGLE-ENDED Page 12 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 011...111 1LSB = 2•V REF/4096 111...110 000...001 ADC CODE ADC CODE 1LSB = V REF/4096 111...111 011...110 000...000 111...111 100...010 100...001 100...000 011...111 000...010 100...001 000...001 100...000 000...000 –V REF + ½LSB 0V +V REF +V REF – 1½LSB – 1LSB ANALOG INPUT FIGURE 21. IDEAL TRANSFER CHARACTERISTICS, DIFFERENTIAL INPUT FIGURE 22. IDEAL TRANSFER CHARACTERISTICS, SINGLE-ENDED INPUT Analog Inputs V Some members of the ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315 and ISL26319 family feature a fully differential input with a nominal full-scale range equal to twice the applied VREF voltage. Those devices with differential inputs have a nominal full scale range equal to twice the applied VREF voltage. Each input swings VREF volts (peak-to-peak), 180° out-of-phase from one another for a total differential input of 2*VREF (refer to Figures 23 and 24). VREF (P-P) 5.0 4.0 AIN– 3.0 VREF (P-P) 2.5Vp-p AIN+ 2.0 ALLOWABLE VCM RANGE 1.0 t AIN+ VREF = 2.5V V ISL2631X/32X VCM FS = +V REF – 1LSB 0 = +½LSB ANALOG INPUT AIN+ – (AIN–) AIN- 5.0 AIN– 5Vp-p AIN+ 4.0 FIGURE 23. DIFFERENTIAL INPUT SIGNALING VCM 3.0 Differential signaling offers several benefits over a single-ended input, such as: • Doubling of the full-scale input range (and therefore the dynamic range) • Improved even order harmonic distortion • Better noise immunity due to common mode rejection Figure 24 shows the relationship between the reference voltage and the full-scale differential input range for two different values of VREF. Note that the common-mode input voltage must be maintained within ±200mV of VREF/2 for differential inputs. ALLOWABLE VCM RANGE 2.0 1.0 t VREF = 5V FIGURE 24. RELATIONSHIP BETWEEN VREF AND FULL-SCALE RANGE FOR DIFFERENTIAL INPUTS Those devices with singled-ended inputs have a ground-referenced peak-to-peak input voltage span equal to the reference voltage. FN7549 Rev 3.00 August 18, 2015 Page 13 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Voltage Reference Input V 5.0 4.0 3.0 2.5Vp-p AIN 2.0 1.0 t VREF = 2.5V V 5Vp-p 5.0 An external reference voltage must be supplied to the VREF pin to set the full-scale input range of the converter. The VREF input on these devices can accept voltages ranging from 2V (nominal) to VDD, however, they are specified with VREF at a voltage of 5V with VDD at 5V. Note that exceeding VDD by more than 100mV can forward bias the ESD protection diodes and degrade measurement accuracy due to leakage current. A lower value voltage reference must be used if the device is operated with VDD at voltages lower than 5V. If the VREF pin is tied to the VDD pin, the VREF pin should be decoupled with a local 1µF ceramic capacitor as described in a later paragraph. Figures 27 and 28 illustrate possible voltage reference options for these ADCs. Figure 27 uses the precision ISL21090 voltage reference, which exhibits exceptionally low drift and low noise. The ISL21090 must be powered from a supply greater than 4.7V. AIN 4.0 Figure 28 illustrates the ISL21010 voltage reference used with these ADCs. The ISL21010 series voltage references have higher noise and drift than the ISL21090 devices, but operate at lower supply voltages. Therefore, these devices can readily be used when these SAR ADCs operate with VDD at voltages less than 5V. 3.0 2.0 1.0 t VREF = 5V FIGURE 25. RELATIONSHIP BETWEEN VREF AND FULL-SCALE RANGE FOR SINGLE-ENDED INPUTS Input Multiplexer The input of the multiplexer connects the selected analog input pins to the ADC input. A proprietary sampling circuit significantly reduces the input drive requirements, resulting in lower overall cost and board space in addition to improved performance. Note that the input capacitance is only 2-3pF during the Sampling phase, changing to 40pF during the Settling phase, resulting in an average input current of 2.5µA and an effective input capacitance of only 4pF (see Figure 26). AC ERROR INPUT VOLTAGE TOTAL DC ERROR ERROR SETTLING ERROR AND NOISE OFFSET ERROR The outputs of ISL21090 or the ISL21010 devices should be decoupled with a 1µF ceramic capacitor. A 1µF, 6.3 V, X7R, 0603 (1608 metric) MLCC type capacitor is recommended for its high frequency performance. The trace length from the VREF pin to this capacitor and the voltage reference output should be as short as possible. The ISL26310 and ISL26313 devices (packaged in 8 pin SOIC packages) derive their voltage reference from the VDD pin. To achieve best performance, the VDD pin of these devices should be bypassed with the 1µF ceramic capacitor mentioned above. Power-Down/Standby Modes In order to reduce power consumption between conversions, a number of user-selectable modes can be utilized by setting the appropriate bits in the Configuration Register. Auto Power-down (PD0 = 0) reduces power consumption by shutting down all portions of the device except the oscillator and digital interface after completion of a conversion. There is a short recovery period after CNV is asserted Low (150µs with external reference). In Auto Sleep mode (PD1 = 1), the device will automatically enter the low-power Sleep mode at the end of the current conversion. Recovery from this mode involves only 2.1µs and may offer an alternative to Power-down mode in some applications. SAMPLING PHASE Output Data Format SETTLING PHASE FIGURE 26. INPUT SAMPLING OPERATION The converter output word is delivered in two’s complement format in differential input mode, and straight binary in single-ended input mode of operation respectively, all MSB-first. Input exceeding the specified full-scale voltage results in a clipped output which will not return to in-range values until after the input signal has returned to the specified allowable voltage range. Data must be read prior to the completion of the current conversion to avoid conflict and loss of data, due to overwriting of the new conversion data into the output register. FN7549 Rev 3.00 August 18, 2015 Page 14 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 5V + BULK 0.1µF 0.1µF 1 DNC DNC 8 2 VIN DNC 7 3 COMP VOUT 6 4 GND 5 TRIM ISL2631X ISL2632X 2.5V VDD VREF 1µF (SEE VOLTAGE REFERENCE INPUT) ISL21090 FIGURE 27. PRECISION VOLTAGE REFERENCE FOR +5V SUPPLY +2.7V TO +3.6V OR +5V + VIN 1 VOUT 2 GND 3 BULK 0.1µF 0.1µF ISL2631X VDD ISL2632X VREF 1.25, 2.048 OR 2.5V 1µF (SEE VOLTAGE REFERENCE INPUT) ISL21010 FIGURE 28. VOLTAGE REFERENCE FOR +2.7V TO +3.6V, OR FOR +5V SUPPLY +2.7V TO +5V BULK 1µF (SEE VOLTAGE REFERENCE INPUT) ISL26310 ISL26313 VDD FIGURE 29. VOLTAGE REFERENCE FOR ISL26310/313 IS DERIVED FROM VDD TABLE 1. OUTPUT CODES - DIFFERENTIAL INPUT VOLTAGE TWO’S COMPLEMENT (12-bit) >(VFS - 1.5 LSB) 7FF VFS - 1.5 LSB 7FF ... 7FE -0.5 LSB -VFS +0.5 LSB 000 … FFF 801 … 800 NOTE: VFS in the table above equals the voltage between AIN+ and AIN-. Differential full scale is equal to 2* VREF. FN7549 Rev 3.00 August 18, 2015 TABLE 2. OUTPUT CODES - SINGLE-ENDED INPUT VOLTAGE BINARY (12-bit) >AIN - 1.5 LSB FFF AIN - 1.5 LSB FFF … FFE 0.5 LSB 001 … 000 <0.5 LSB 000 NOTE: Single-ended full scale is equal to VREF. Page 15 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Serial Digital Interface The ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315 and ISL26319 families are utilizes an SPI-compatible interface to set the device configuration and read conversion data. This flexible interface provides 3 modes of operation: Reading After Conversion (RAC), Reading During Conversion (RDC), and Reading Spanning Conversions (RSC), with an additional option providing an End of Conversion (EOC) indication on the SDO output in all 3 modes. The choice of operating mode is determined by the timing of the signals on the serial interface. The interface consists of the data clock (SCLK), serial digital input (SDI), serial digital output (SDO), and the conversion control input (CNV). From the Idle state (after completion of a prior conversion), a High-to-Low transition on CNV indicates the beginning of input signal acquisition, with the Conversion then initiated by a subsequent Low-to-High transition. When CNV is Low, input data presented to SDI is latched on the rising edge of SCLK. Output data will be present at SDO on the falling edge of SCLK. SDO is in the high-impedance state whenever CNV is High, and activity on SCLK should be avoided during this time to avoid corruption of the conversion process. SCLK should be Low when CNV is High. During the Nth conversion, output data indicates the conversion data and configuration settings for the N-1th conversion, while the current configuration settings apply to the N+1th conversion. In order to minimize errors due to digital noise coupling, there should be no activity on the serial interface after the specified tDATA period. Data should be read before the conversion is completed to avoid the newer results being overwritten resulting in a permanent loss of data. Reading After Conversion Mode Without EOC In this mode, data transfer always occurs during the Acquisition phase, supporting the widest variety of interface data rates. Figure 30 depicts a timing waveform in this mode. From Idle, the device enters the Acquisition phase when CNV is taken Low. SDO emerges High from a high-impedance state, waiting for an SCLK to present the MSB of the current output data word. The configuration settings can be updated using SDI and at the same time previous conversion results can be read from SDO. After the communication is completed or the required acquisition time (tACQ) has elapsed – whichever is later – CNV transitions High indicating the start of conversion. CNV must be held High continuously for a minimum of 7.2µs (at 125kSPS) so that the conversion is completed without enabling EOC. Subsequently CNV may be asserted Low at any time so that the next Acquisition phase can begin. This method is suitable for hosts which operate with lower frequency SCLK. Reading During Conversion Mode Without EOC From Idle, the user initiates the input signal Acquisition mode by taking CNV Low, and then initiates a conversion after tACQ by pulsing CNV High. After the conversion starts, data is exchanged on the serial interface while CNV is held Low (see Figure 31). CNV must also be asserted High before tDATA to avoid enabling EOC. This method is ideal for hosts with high SCLK communication rates to operate the device at the highest conversion rates. At the end of conversion the device enters the Idle state. After the host is certain that the conversion is completed (7.2µs after conversion is initiated at 125kSPS) a new acquisition can be initiated by pulling CNV Low which will initiate the Acquisition state. Reading Spanning Conversion Mode Without EOC In applications desiring slower interface data rates and while still maintaining maximum possible throughput, RSC mode can be used to transfer data during both the Acquisition and Conversion phases, as shown in Figure 32. Data exchange begins during the Acquisition phase until CNV is asserted High to initiate a conversion and SDO returns to the high-impedance state, interrupting the exchange. After CNV is returned Low, SDO will return to the state prior to the CNV pulse in order to avoid data loss. Once again data exchange occurs when CNV is Low. CNV must be asserted High before tDATA in order to avoid enabling EOC. At the end of conversion the device enters the Idle state. After the host is certain that the conversion is completed (7.2µs after conversion is initiated at 125kSPS) a new acquisition can be initiated by pulling CNV Low, which will take the device back to Acquisition state from Idle state. Note that when using slower SPI rates the data transfer time can exceed the minimum acquisition time, which will limit the conversion throughput to less than the maximum specified rate. For example, a 12-bit data transfer takes 12µs with a 1MHz SPI clock. This adds to the 7.2µs conversion time for an effective throughput of 52ksps. FN7549 Rev 3.00 August 18, 2015 Page 16 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 ADC STATE Power-Up Conversion N Acquisition Idle Conversion Conversion N+1 Acquisition Idle Conversion Idle Acq. tACQ CNV tSCLK tSCLKH tSDOZ_D tCNV_SCLK SCLK tSCLKL SDI D15 tSDI_H D5 ... Configuration N+1 D14 D15 D4 Hi-Z State D4 tSDI_SU tSDO_V MSB-1 . . . D1 LSB Conversion Result N-1 SDO D5 ... Configuration N+2 D14 MSB MSB MSB-1 . . . Conversion Result N LSB FIGURE 30. TIMING DIAGRAM FOR READING AFTER CONVERSION MODE, WITHOUT EOC ADC STATE Power-Up Idle Conversion N Conversion Acquisition tACQ Conversion N+1 Idle Acquisition Conversion tDATA Idle tCNV CNV tSCLK tSCLKH tCNV_CLK SCLK tSCLKL SDI D15 Hi-Z State tSDI_H D5 ... Configuration N+1 D14 D5 D14 ... Configuration N+2 D4 tSDI_SU D4 tSDO_V D1 LSB ... Conversion Result N-1 SDO MSB MSB-1 MSB D1 ... Conversion Result N MSB-1 FIGURE 31. TIMING DIAGRAM FOR READING DURING CONVERSION MODE, WITHOUT EOC ADC STATE Conversion N Power-Up Idle Acquisition Conversion Idle Acquisition Conversion N+1 Conversion tCNV Idle tDATA CNV tACQ tSCLKH tCNV_SCLK SCLK tSCLK SDI D15 tSCLKL D14 D13 D12 tSDI_H ... D4 Configuration N+1 SDO MSB MSB-1 MSB-1 MSB-2 Hi-Z State ... Conversion Result N-1 D1 LSB D15 D14 D13 ... D12 D4 tSDI_SU Configuration N+2 tSDO_V MSB MSB-1 MSB-1 MSB-2 ... D1 Conversion Result N Note: Transition from Acquisition to Conversion mode may occur after any integer number of clock cycles (provided that the minimum tACQ is satisfied). FIGURE 32. TIMING DIAGRAM FOR READING SPANNING CONVERSION MODE, WITHOUT EOC FN7549 Rev 3.00 August 18, 2015 Page 17 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Reading After Conversion Mode, with EOC Reading Spanning Conversion Mode, with EOC In this mode (Figure 33), after CNV is asserted Low to start input acquisition, a data exchange is executed by SCLK during the Acquisition period. CNV is asserted High briefly to initiate a Conversion, forcing SDO to a high-impedance state. SDO returns HIGH when CNV is asserted Low during the entire conversion period. After initiating an Acquisition by bringing CNV Low, the user begins exchanging data as previously mentioned, until CNV is asserted High to initiate a conversion and SDO returns to a high-impedance state, interrupting the exchange. And, after CNV is returned Low, SDO will return to the state prior to the CNV pulse in order to avoid losing data interrupted by the conversion pulse (see Figure 35). The user should take care to observe the tDATA period in order to minimize the effects of digital noise on sensitive portions of conversion. After completion of the data exchange, an additional pulse on SCLK forces SDO to a high-impedance state. At the end of conversion, the device asserts SDO Low indicating the end of conversion. The device then returns to Idle, waiting for a pulse on CNV to initiate a new Acquisition cycle. At the end of conversion, the device asserts SDO Low to indicate that the conversion is complete. This may be used as an interrupt to start the Acquisition phase. It should be noted (as indicated in Figure 33) that an additional pulse on CNV is required at the end of conversion to take the part back to Acquisition from Idle state. As discussed in section “Reading After Conversion Mode Without EOC” . The acquisition time (tACQ) may limit the conversion throughput at slower SPI clock rates. Accessing the Configuration Register During Data Readback Reading During Conversion Mode, with EOC From Idle, a falling edge on CNV initiates the Acquisition mode, and then a rising edge initiates a Conversion. After the conversion is initiated, CNV is asserted Low once again. Data exchange across SDI and SDO can proceed while CNV is Low, again observing the requirements of the tDATA period in order to minimize the effects of digital noise on sensitive portions of the conversion. In this mode, an additional pulse is required on SCLK after the completion of the data exchange, to transition SDO to the high-impedance state. Later, SDO is asserted low by the device indicating end of conversion. The device then returns to Idle. The falling edge of SDO may be used as an interrupt to start the Acquisition phase (see Figure 34). The Configuration Register contains the channel address of the current conversion data. The contents can be accessed during a normal data output sequence by continuing to clock data from SDO if the register readback mode is enabled. Both 12-bit output data words and the 16-bit configuration word are output in 28 SCLK periods, as shown in Figure 36, which demonstrates an example sequence. Note that SDO goes into the high-impedance state when CNV is High. The Configuration Register can be read during any Read Sequence by generating the additional SCLKs, with the restriction that the sequence must be completed prior to the end of the current conversion. This will prevent loss of data due to overwriting of the new conversion data into the output and configuration registers. ADC STATE Power-Up Conversion N Acquisition Idle Conversion Conversion N+1 Acquisition Idle Conversion tACQ Idle Acq. tCNV CNV tSCLK tSCLKH tCNV_SCLK SCLK tSCLKL SDI D15 SDO D5 ... Configuration N+1 D14 tSDI_H D4 Hi-Z State MSB-1 . . . D1 LSB Conversion Result N-1 MSB D15 D5 ... Configuration N+2 D14 D4 tSDI_SU tSDO_V MSB MSB-1 . . . Conversion Result N LSB FIGURE 33. TIMING DIAGRAM FOR READING AFTER CONVERSION MODE WITH EOC ON SDO OUTPUT FN7549 Rev 3.00 August 18, 2015 Page 18 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 ADC STATE Power-Up Idle Conversion N Conversion Acquisition tACQ Conversion N+1 Idle Acquisition Conversion tDATA Idle tCNV CNV tSCLK tSCLKH tCNV_CLK SCLK tSCLKL SDI D15 Hi-Z State tSDI_H D5 ... Configuration N+1 D14 D5 D14 ... Configuration N+2 D4 tSDI_SU D4 tSDO_V SDO MSB ... MSB-1 D1 LSB MSB Conversion Result N-1 MSB-1 ... D1 Conversion Result N FIGURE 34. TIMING DIAGRAM FOR READING DURING CONVERSION MODE WITH EOC ON SDO OUTPUT ADC STATE Power-Up Idle Acquisition Conversion N Conversion Idle Conversion N+1 Conversion Acquisition tCNV Idle tDATA CNV tACQ tSCLKH tCNV_SCLK SCLK tSCLK SDI D15 tSCLKL D14 D13 MSB tSDI_H ... D4 D15 Configuration N+1 Hi-Z State SDO D12 D14 D13 ... D12 D4 tSDI_SU Configuration N+2 tSDO_V MSB-1 ... Conversion Result N-1 MSB-1 MSB-2 D1 LSB MSB MSB-1 MSB-1 MSB-2 ... D1 Conversion Result N Note: Transition from Acquisition to Conversion mode may occur after any integer number of clock cycles (provided that the minimum tACQ is satisfied). FIGURE 35. TIMING DIAGRAM FOR READING SPANNING CONVERSIONS MODE WITH EOC ON SDO OUTPUT ADC STATE Power-Up Conversion N Acquisition Idle Conversion Idle CNV SCLK SDI D15 D14 ... D5 Configuration N+1 SDO D4 Hi-Z State D1 LSB Cfg15 Cfg14 ... . . . Cfg1 Cfg0 Conversion Result N-1 Configuration settings of N-1 Result MSB MSB-1 FIGURE 36. TIMING DIAGRAM FOR READING AFTER CONVERSION WITH REGISTER READBACK, WITHOUT EOC FN7549 Rev 3.00 August 18, 2015 Page 19 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Device Configuration Registers Power Management Modes The Input Multiplexer Channel Select and power management features are controlled by loading the appropriate bits into the 16-bit Configuration Register through the serial port, MSB-first, as shown below. The first two Load bits LD1-LD0 must be set to “11” in order to perform a Register update: any other setting will leave the Register unchanged. Changes to the Configuration Register will be implemented internally immediately following the completion of the current conversion, or require a dummy conversion in order to take effect. Also, in the case of all power management features, a recovery time will be incurred when returning to normal operation, as indicated. In all SPI interface modes (RAC, RDC, etc.) the device has three states of operation: Acquisition, Conversion and Idle. Power management modes decide the state of the ADC in Idle mode and are selected by the PM bits in the Configuration Register as shown in Tables 3 and 4. TABLE 3. CONFIGURATION REGISTER BIT 15 (MSB) 14 13 12 11 10 9 8 LD1 LD0 ADDR2 ADDR1 ADDR0 PM1 PM0 Unused BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) RGRD Unused TABLE 4. CONFIGURATION REGISTER 2 BIT(S) DESCRIPTION 15:14 Register Load word, set to “11” to update registers, otherwise previous settings are retained. In the default mode (Continuous Operation) the ADC is fully powered in the Idle state and can be taken back to the Acquisition state instantaneously. In this mode the ADC can be operated with maximum throughput and hence is ideally suitable for applications where the ADC is operated continuously. In Auto Sleep Mode the ISL263XX will be in a sleep state consuming less than 0.4mA. However, it should be noted that the requirements on tACQ are more stringent in Auto Sleep mode since the device must wake up and then perform the Acquisition. In Auto Power Down Mode (as selected by PM bits) the ADC will be in power-down condition during the Idle period, consuming less than 5µA of current. Wake-up time takes 150µs. The acquisition time (tACQ) must be increased to account for this delay. The power management modes provide a high degree of flexibility in trading average power consumption versus the required throughput. Significant power savings can be achieved by operating in either Auto Sleep Mode or Auto Power-Down mode depending on the throughput requirements. 13:11 Multiplexer Channel Select word ADDR2:0. 000H: Channel AIN0 (single-ended input devices) or AIN0+/AIN0(differential input devices). 001H: Channel AIN1 or AIN1+/AIN1010H: Channel AIN2 or AIN2+/AIN2011H: Channel AIN3 or AIN3+/AIN3100H: Channel AIN4 101H: Channel AIN5 110H: Channel AIN6 111H: Channel AIN7 10:9 Power Management Configuration Control. 00H: Auto Power-Down mode. Device will go into Power-down mode automatically at the end of the next conversion cycle. 01H: Continuous Operation mode (default). Device remains fully powered at all times. 1xH: Auto Sleep Mode. Device will enter reduced-power Sleep mode automatically at the end of the next conversion cycle. A "1" in PM1 overrides the setting in PM0. 8 Unused. 7 Register readback mode. "1" means register readback is enabled resulting in configuration settings to be output along with conversion results. "0" (default) mode of operation register settings are not output. 6:0 Unused. FN7549 Rev 3.00 August 18, 2015 Page 20 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest Rev. DATE REVISION CHANGE August 18, 2015 FN7549.3 Updated Ordering Information table on page 3. Updated About Intersil section. August 23, 2013 FN7549.2 Updated Figure 22 on page 13, IDEAL TRANSFER CHARACTERISTICS, SINGLE-ENDED INPUT. Block diagram on page 2, corrected temperature sensor drawing and added an input to the Mux and ADC section. June 22, 2012 January 11, 2012 FN7549.1 Added Part Numbers ISL26310, ISL26311, ISL26313 throughout document Added SOIC Package throughout document Updated Features List by Removing following bullets: o 125kSPS Conversion Rate o Pin-Compatible 2/4-Channel Differential or 4/8-Channel Single-Ended Inputs o Internal 2.5V Reference o Available in Popular TSSOP Package o Pb-Free (RoHS Compliant) Updated Functional Block Diagram on page 1 by removing voltage reference Updated Pin Compatible Family by removing ISL264XX PARTS Updated Pin Description Table to include all parts Updated conditions in Electrical Spec Table from: Electrical Specifications VREF+ = VDD(External) V, VDD = 3.3V to 5V, VCM = VDD/2, SCLK = 20MHz... To: Electrical Specifications VREF = VDD V, VDD = 2.7V to 5V, VCM = VDD/2, SCLK = 20MHz... Removed VREFIN specs from Voltage Reference Section Removed Test Level from tACQ in Auto Power Down Mode Replaced Figures 3 and 4 DNL and INL Replaced Figure 17 by changing from single line curve to frequency mode Rewrote Functional Description Section FN7549.0 Initial Release. About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support © Copyright Intersil Americas LLC 2012-2015. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN7549 Rev 3.00 August 18, 2015 Page 21 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Package Outline Drawing M16.173 16 LEAD THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP) Rev 2, 5/10 A 1 3 5.00 ±0.10 SEE DETAIL "X" 9 16 6.40 PIN #1 I.D. MARK 4.40 ±0.10 2 3 0.20 C B A 1 8 B 0.65 0.09-0.20 END VIEW TOP VIEW H 1.00 REF - 0.05 C 1.20 MAX SEATING PLANE 0.90 +0.15/-0.10 GAUGE PLANE 0.25 +0.05/-0.06 5 0.10 M C B A 0.10 C 0°-8° 0.05 MIN 0.15 MAX SIDE VIEW 0.25 0.60 ±0.15 DETAIL "X" (1.45) NOTES: 1. Dimension does not include mold flash, protrusions or gate burrs. (5.65) Mold flash, protrusions or gate burrs shall not exceed 0.15 per side. 2. Dimension does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.25 per side. 3. Dimensions are measured at datum plane H. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. 5. Dimension does not include dambar protrusion. Allowable protrusion shall be 0.08mm total in excess of dimension at maximum material condition. Minimum space between protrusion and adjacent lead (0.65 TYP) (0.35 TYP) TYPICAL RECOMMENDED LAND PATTERN is 0.07mm. 6. Dimension in ( ) are for reference only. 7. Conforms to JEDEC MO-153. FN7549 Rev 3.00 August 18, 2015 Page 22 of 23 ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319 Package Outline Drawing M8.15 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 4, 1/12 DETAIL "A" 1.27 (0.050) 0.40 (0.016) INDEX 6.20 (0.244) 5.80 (0.228) AREA 0.50 (0.20) x 45° 0.25 (0.01) 4.00 (0.157) 3.80 (0.150) 1 2 8° 0° 3 0.25 (0.010) 0.19 (0.008) SIDE VIEW “B” TOP VIEW 2.20 (0.087) SEATING PLANE 5.00 (0.197) 4.80 (0.189) 1.75 (0.069) 1.35 (0.053) 1 8 2 7 0.60 (0.023) 1.27 (0.050) 3 6 4 5 -C- 1.27 (0.050) 0.51(0.020) 0.33(0.013) SIDE VIEW “A 0.25(0.010) 0.10(0.004) 5.20(0.205) TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensioning and tolerancing per ANSI Y14.5M-1994. 2. Package length does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 3. Package width does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 4. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 5. Terminal numbers are shown for reference only. 6. The lead width as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 7. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 8. This outline conforms to JEDEC publication MS-012-AA ISSUE C. FN7549 Rev 3.00 August 18, 2015 Page 23 of 23