ML6201 ML6201 Series Positive Voltage Regulator Application Features Battery Powered Equipment Palmtops Portable Cameras and Video Recorders Reference Voltage Sources General Description CMOS Low Power Consumption : Typical 3.3uAat Vout=5.0V Output Voltage Range : 1.1V to 6.0V in 0.1V increments HighlyAccurate: Output Voltage + 3% for 1.1V to 1.9V Output Voltage + 2% for 2.0V to 6.0V Maximum Output Current: 250mA (within the maximum power dissipation, Vout=5.0V) Small Input-Output Voltage Differential: 0.16V at 100mAand 0.4V at 200mA Input stability: Typ. 0.2%/V PackageAvailable: SOT- 23-5 (250mW), SOT- 89 (500mW) & TO - 92 (300mW) Block Diagram The ML6201 is a group of positive voltage output, three-pin regulator which provides high output current even when the input/output voltage differential is small. The ML6201 consists of a high-precision voltage reference, an error correction circuit, and a current limited output driver. Absolute Maximum Ratings Parameter Input Voltage Output Current Output Voltage SOT-23-5 Continuous Total Power Dissipation SOT-89 TO-92 Operating Ambient Temperature Storage Temperature Symbol VIN IOUT VOUT Ratings 10 500 VSS-0.3 ~VIN+0.3 250 Units V mA V Pd 500 mW Topr Tstg 300 -40 ~ +70 -40 ~ +70 P1/6 o C C o Rev. A, June 2005 ML6201 Pin Configuration SOT-23-5 Package Pin Number SOT-23-5 SOT-89 TO-92 5 1 1 2 2 2 1 3 3 3 4 SOT-89 TO-92 Pin Name Function VOUT VSS VIN (NC) (NC) Output Ground Power Input No Connection No Connection Standard Circuit Note on Use 1. Oscillation may occur as a result of the impedance present between the power supply and the IC’s input. Please use a capacitor (CIN) of at least 1uF, when the impedance is 10 ohm or more. With a large output current, Voltage output can be stabilised by increasing capacitor (CIN) size. If CIN is small and capacitor (CL) size is increased, oscillation may occur. In such cases, Voltage output can be stabilised by either increasing the size of CIN or decreasing the size of CL. 2. Please ensure that output current (IOUT) is less than Pd / (VIN-VOUT) and does not exceed the stipulated Continuous Total Power Dissipation value (Pd). Test Circuit Test Circuit 2 Test Circuit 1 P2/6 Rev. A, June 2005 ML6201 Electrical Characteristic ML6201P502 VOUT(T)=5.0V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Symbol VOUT(E) (Note 2) IOUT max ∆VOUT Vdif1 Vdif2 ISS ∆VOUT ∆VIN * VOUT VIN Conditions IOUT=40mA VIN=6.0V VIN=6.0V, VOUT(E) ≥ 4.5V VIN=6.0V, 1mA≤IOUT≤100mA IOUT=100mA IOUT=200mA VIN=6.0V IOUT=40mA 6.0V≤VIN≤10.0V Min Typ Max Units Circuit 4.900 5.000 5.100 V 1 40 120 380 3.3 80 400 750 4.5 mA mV mV mV uA 1 1 1 1 2 0.2 0.3 %V 1 10 V - Units Circuit 250 ML6201P402 VOUT(T)=4.0V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Symbol VOUT(E) (Note 2) IOUT max ∆VOUT Vdif1 Vdif2 ISS ∆VOUT ∆VIN * VOUT VIN Conditions IOUT=40mA VIN=5.0V VIN=5.0V, VOUT(E) ≥3.6V VIN=5.0V, 1mA≤IOUT≤100mA IOUT=90mA IOUT=180mA VIN=5.0V IOUT=40mA 5.0V≤VIN≤10.0V Min Typ Max 3.920 4.000 4.080 V 1 45 170 400 3.0 90 400 750 4.5 mA mV mV mV uA 1 1 1 1 2 0.2 0.3 %V 1 10 V - Units Circuit 200 ML6201P302 VOUT(T)=3.0V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Symbol VOUT(E) (Note 2) IOUT max ∆VOUT Vdif1 Vdif2 ISS ∆VOUT ∆VIN * VOUT VIN Conditions IOUT=40mA VIN=4.0V VIN=4.0V, VOUT(E) ≥2.7V VIN=4.0V, 1mA≤IOUT≤80mA IOUT=80mA IOUT=150mA VIN=4.0V IOUT=40mA 4.0V≤VIN≤10.0V Min Typ Max 2.940 3.000 3.060 V 1 45 180 400 2.8 90 450 850 4.5 mA mV mV mV uA 1 1 1 1 2 0.2 0.3 %V 1 10 V - Units Circuit 150 ML6201P202 VOUT(T)=2.0V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Symbol VOUT(E) (Note 2) IOUT max ∆VOUT Vdif1 Vdif2 ISS ∆VOUT ∆VIN * VOUT VIN Conditions IOUT=40mA VIN=3.0V VIN=3.0V, VOUT(E) ≥1.8V VIN=3.0V, 1mA≤IOUT≤60mA IOUT=60mA IOUT=100mA VIN=3.0V IOUT=40mA 3.0V≤VIN≤10.0V Min Typ Max 1.960 2.000 2.040 V 1 45 180 400 2.5 90 450 850 4.5 mA mV mV mV uA 1 1 1 1 2 0.2 0.3 %V 1 10 V - 100 Note : 1. VOUT(T) = Specified Output Voltage. 2. VOUT(E) = Effective Output Voltage (i.e. the output voltage when (VOUT(T)+1.0V) is provided at the VIN pin while maintaining a certain IOUT value). 3. Vdif = VIN1(Note 4) – VOUT(E) 4. VIN1 = The input voltage at the time 98% of VOUT (E) is output (input voltage has been gradually reduced). P3/6 Rev. A, June 2005 ML6201 Electrical Characteristics by Output Voltage Part Number Output voltage VOUT(V) Conditions ML6201P113 ML6201P123 ML6201P133 ML6201P143 ML6201P153 ML6201P163 ML6201P173 ML6201P183 ML6201P193 ML6201P202 ML6201P212 ML6201P222 ML6201P232 ML6201P242 ML6201P252 ML6201P262 ML6201P272 ML6201P282 ML6201P292 ML6201P302 ML6201P312 ML6201P322 ML6201P332 ML6201P342 ML6201P352 ML6201P362 ML6201P372 ML6201P382 ML6201P392 ML6201P402 ML6201P412 ML6201P422 ML6201P432 ML6201P442 ML6201P452 ML6201P462 ML6201P472 ML6201P482 ML6201P492 ML6201P502 ML6201P512 ML6201P522 ML6201P532 ML6201P542 ML6201P552 ML6201P562 ML6201P572 ML6201P582 ML6201P592 ML6201P602 MIN. 1.067 1.164 1.261 1.358 1.455 1.552 1.649 1.746 1.843 1.960 2.058 2.156 2.254 2.352 2.450 2.548 2.646 2.744 2.842 2.940 3.038 3.136 3.234 3.332 IOUT=40mA 3.430 VIN=VOUT(T)+1V 3.528 3.626 3.724 3.822 3.920 4.018 4.116 4.214 4.312 4.410 4.508 4.606 4.704 4.802 4.900 4.998 5.096 5.194 5.292 5.390 5.488 5.586 5.684 5.782 5.880 TYP. 1.100 1.200 1.300 1.400 1.500 1.600 1.700 1.800 1.900 2.000 2.100 2.200 2.300 2.400 2.500 2.600 2.700 2.800 2.900 3.000 3.100 3.200 3.300 3.400 3.500 3.600 3.700 3.800 3.900 4.000 4.100 4.200 4.300 4.400 4.500 4.600 4.700 4.800 4.900 5.000 5.100 5.200 5.300 5.400 5.500 5.600 5.700 5.800 5.900 6.000 Max Output Current IOUT max(mA) Load Stability ∆ VOUT(mV) Conditions TYP. MAX. MAX. Conditions MIN. 1.133 1.236 1.339 1.442 VIN=VOUT(T)+1V 80 1.545 1mA<IOUT<40mA 1.648 1.751 1.854 1.957 2.040 2.142 2.244 2.346 VIN=VOUT(T)+1V 2.448 100 1mA<IOUT<60mA 2.550 2.652 2.754 2.856 2.958 3.060 3.162 3.264 3.366 VIN= VOUT(T)+1V 3.468 VIN=VOUT(T)+1V 150 1mA<IOUT<80mA 3.570 VOUT(E)> 3.672 VOUT(T)*0.9 3.774 3.876 3.978 4.080 4.182 4.284 4.386 VIN=VOUT(T)+1V 4.488 200 1mA<IOUT<100mA 4.590 4.692 4.794 4.896 4.998 5.100 5.202 5.304 5.406 5.508 VIN=VOUT+1V 250 5.610 1mA<IOUT<100mA 5.712 5.814 5.916 6.018 6.120 P4/6 45 90 I-O Voltage Differential Vdif1(mV) Conditions TYP. MAX. IOUT=20mA 250 450 IOUT=30mA 250 450 IOUT=40mA 250 450 45 90 IOUT=60mA 180 450 45 90 IOUT=80mA 180 450 45 90 IOUT=90mA 170 400 40 80 IOUT=100mA 120 400 Rev. A, June 2005 ML6201 Part Number I-O Voltage Differential Vdif2(mV) Conditions ML6201P113 ML6201P123 ML6201P133 ML6201P143 ML6201P153 ML6201P163 ML6201P173 ML6201P183 ML6201P193 ML6201P202 ML6201P212 ML6201P222 ML6201P232 ML6201P242 ML6201P252 ML6201P262 ML6201P272 ML6201P282 ML6201P292 ML6201P302 ML6201P312 ML6201P322 ML6201P332 ML6201P342 ML6201P352 ML6201P362 ML6201P372 ML6201P382 ML6201P392 ML6201P402 ML6201P412 ML6201P422 ML6201P432 ML6201P442 ML6201P452 ML6201P462 ML6201P472 ML6201P482 ML6201P492 ML6201P502 ML6201P512 ML6201P522 ML6201P532 ML6201P542 ML6201P552 ML6201P562 ML6201P572 ML6201P582 ML6201P592 ML6201P602 TYP. MAX. IOUT=40mA 450 850 IOUT=60mA 450 850 IOUT=80mA 450 850 IOUT=100mA 400 850 IOUT=150mA 400 850 Supply Current ISS(uA) Conditions TYP. MAX. 2.0 4.5 2.5 4.5 2.8 4.5 VIN=VOUT(T)+1V Input Stability Input Voltage ∆ VOUT/(∆ ∆ VIN*VOUT) (%V) VIN(V) Conditions TYP. MAX. MAX. 0.2 IOUT=40mA VOUT(T)+1V<VIN<10V 10 0.2 IOUT=180mA 400 750 3.0 4.5 IOUT=200mA 380 750 3.3 4.5 P5/6 0.4 0.3 Rev. A, June 2005 ML6201 Ordering Information Designator a b c d G Description Output Voltage eg. 30=3.0V 50=5.0V Output Voltage Accuracy 2 = + 2.0% 3 = + 3.0% Package Type M = SOT-23-5 P = SOT-89 T = TO-92 Device Orientation R = Embossed Tape (Orientation of Device : Right) L = Embossed Tape (Orientation of Device : Left) B = Bag (TO-92) H = Paper Tape (TO-92) G = Lead Free Part Marking SOT-23-5 : Designator 1 2,3 4 Description Type V = Positive Voltage Regulator Output Voltage eg. 30 = 3.0V Internal Code SOT-89 : Designator 1 2,3 4 5 Description Type V = Positive Voltage Regulator Output Voltage eg. 30 = 3.0V Output Voltage Accuracy 2 = + 2.0% 3 = + 3.0% Internal Code TO-92 : Designator 1 2,3 4 5 6, 7 8, 9 Description Type V = Positive Voltage Regulator Output Voltage eg. 30 = 3.0V Output Voltage Accuracy 2 = + 2.0% 3 = + 3.0% Internal code Year Code eg. 05 = Year 2005 Week Code eg. 30 = Week 30 The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. P6/6 Rev. A, June 2005