LD1085 series 3A Low drop positive voltage regulator adjustable and fixed Features ■ Typical dropout 1.3V (at 3A) ■ Three terminal adjustable or fixed output voltage 1.5V, 1.8V, 2.5V, 3.3V, 5V, 12V. ■ Guaranteed output current up to 3A ■ Output tolerance ±1% at 25°C and ±2% in full temperature range ■ Internal power and thermal limit ■ Wide operating temperature range -40°C to 125°C ■ Package available: TO-220, TO-220FP, DPAK, D2PAK, D2PAK/A ■ Pinout compatibility with standard adjustable VREG TO-220 DPAK TO-220FP D2PAK D2PAK/A better performances in term of drop and output tolerance. Description The LD1085 is a LOW DROP Voltage Regulator able to provide up to 3A of Output Current. Dropout is guaranteed at a maximum of 1.2V at the maximum output current, decreasing at lower loads. The LD1085 is pin to pin compatible with the older 3-terminal adjustable regulators, but has A 2.85V output version is suitable for SCSI-2 active termination. Unlike PNP regulators, where a part of the output current is wasted as quiescent current, the LD1085 quiescent current flows into the load, so increase efficiency. Only a 10µF minimum capacitor is need for stability. The device is supplied in TO-220, TO-220FP, DPAK, D2PAK and D2PAK/A. On chip trimming allows the regulator to reach a very tight output voltage tolerance, within ±1% at 25°C. Schematic diagram June 2007 Rev. 18 1/27 www.st.com 27 LD1085 series Contents 1 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Schematic application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7 Order codes 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2/27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 LD1085 series Pin configuration 1 Pin configuration Figure 1. Pin connections (top view) TO-220 TO-220FP D2PAK D2PAK/A DPAK 3/27 Maximum ratings LD1085 series 2 Maximum ratings Table 1. Absolute maximum ratings Symbol Parameter Value Unit 30 V VI DC Input voltage IO Output current Internally Limited mA PD Power dissipation Internally Limited mW TSTG Storage temperature range -55 to +150 °C TOP Operating junction temperature range -40 to +125 °C Note: Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied Table 2. Thermal Data Symbol Parameter TO-220 DPAK D2PAK D2PAK/A Unit RthJC Thermal resistance junction-case 3 8 3 °C/W RthJA Thermal resistance junction-ambient 50 100 62.5 °C/W 4/27 LD1085 series 3 Schematic application Figure 2. Application circuit Schematic application R V O = V REF ⋅ ⎛ 1 + ------2-⎞ ⎝ R ⎠ 1 5/27 Electrical characteristics LD1085 series 4 Electrical characteristics Table 3. Electrical characteristics of LD1085#15 (VI=4.5V, CI = CO =10μF, TA = -40 to 125°C, unless otherwise specified). Symbol Parameter Test Min. Typ. Max. Unit IO = 0 mA, TJ = 25°C 1.485 1.5 1.515 V IO = 0 to 3A, VI = 3.1 to 30V 1.47 1.5 1.53 V IO = 0 mA, VI = 3.1 to 18V, TJ = 25°C 0.2 4 mV IO = 0 mA, VI = 3.1 to 15V 0.4 4 mV IO = 0 to 3A, TJ = 25°C 2 10 mV IO = 0 to 3A 4 20 mV VO Output voltage (1) ΔVO Line Regulation ΔVO Load Regulation Vd Dropout Voltage IO =3 A 1.3 1.5 V Iq Quiescent Current VI ≤30V 5 10 mA Isc Short Circuit Current SVR eN VI - VO = 5V 3.2 4.5 A VI - VO = 25V 0.2 0.5 A Thermal Regulation TA = 25°C, 30ms pulse Supply Voltage Rejection f = 120 Hz, CO = 25µF, IO = 3A VI = 7.5 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C, f =10Hz to 10KHz S Temperature Stability S Long Term Stability TA = 125°C, 1000Hrs 1. See short-circuit current curve for available output current at fixed dropout. 6/27 0.008 60 0.04 %/W 72 dB 0.003 % 0.5 % 0.5 % LD1085 series Table 4. Symbol Electrical characteristics Electrical characteristics of LD1085#18 (VI=4.8V, CI = CO =10μF, TA = -40 to 125°C, unless otherwise specified). Parameter Test Min. Typ. Max. Unit IO = 0 mA, TJ = 25°C 1.782 1.8 1.818 V IO = 0 to 3A, VI = 3.4 to 30V 1.764 1.8 1.836 V IO = 0 mA, VI = 3.4 to 18V TJ = 25°C 0.2 4 mV IO = 0 mA, VI = 3.4 to 15V 0.4 4 mV IO = 0 to 3A, TJ = 25°C 2 10 mV IO = 0 to 3A 4 20 mV VO Output voltage (1) ΔVO Line Regulation ΔVO Load Regulation Vd Dropout Voltage IO = 3 A 1.3 1.5 V Iq Quiescent Current VI ≤30V 5 10 mA Isc Short Circuit Current SVR eN VI - VO = 5V 3.2 4.5 A VI - VO = 25V 0.2 0.5 A Thermal Regulation TA = 25°C, 30ms pulse Supply Voltage Rejection f = 120 Hz, CO = 25µF, IO = 3A VI = 7.5 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C, f =10Hz to 10KHz S Temperature Stability S Long Term Stability TA = 125°C, 1000Hrs 0.008 60 0.04 %/W 72 dB 0.003 % 0.5 % 0.5 % 1. See short-circuit current curve for available output current at fixed dropout. 7/27 Electrical characteristics Table 5. Symbol LD1085 series Electrical characteristics of LD1085#25 (VI=5.5V, CI = CO =10μF, TA = -40 to 125°C, unless otherwise specified). Parameter Test Min. Typ. Max. Unit IO = 0 mA, TJ = 25°C 2.475 2.5 2.525 V IO = 0 to 3A, VI = 4.1 to 30V 2.45 2.5 2.55 V IO = 0 mA, VI = 4.1 to 18V, TJ = 25°C 0.2 4 mV IO = 0 mA, VI = 4.1 to 18V 0.4 4 mV IO = 0 to 3A, TJ = 25°C 2 10 mV IO = 0 to 3A 4 20 mV VO Output voltage (1) ΔVO Line regulation ΔVO Load regulation Vd Dropout voltage IO = 3A 1.3 1.5 V Iq Quiescent current VI ≤30V 5 10 mA Isc Short circuit current SVR eN VI - VO = 5V 3.2 4.5 A VI - VO = 25V 0.2 0.5 A Thermal regulation TA = 25°C, 30ms pulse Supply voltage rejection f = 120 Hz, CO = 25µF, IO = 3A VI = 7.5 ± 3V RMS Output noise voltage (% of TA = 25°C, f =10Hz to 10KHz VO) S Temperature stability S Long term stability TA = 125°C, 1000Hrs 1. See short-circuit current curve for available output current at fixed dropout. 8/27 0.008 60 0.04 %/W 72 dB 0.003 % 0.5 % 0.5 % LD1085 series Table 6. Symbol Electrical characteristics Electrical characteristics of LD1085#33 (VI=6.3V, CI = CO =10μF, TA = -40 to 125°C, unless otherwise specified). Parameter Test Min. Typ. Max. Unit IO = 0 mA, TJ = 25°C 3.267 3.3 3.333 V IO = 0 to 3A, VI = 4.9 to 30V 3.234 3.35 3.366 V 0.5 6 mV IO = 0 mA, VI = 4.9 to 18V 1 6 mV IO = 0 to 3A, TJ = 25°C 3 15 mV IO = 0 to 3A 7 20 mV VO Output voltage (1) ΔVO Line regulation ΔVO Load regulation Vd Dropout voltage IO = 3A 1.3 1.5 V Iq Quiescent current VI ≤30V 5 10 mA Isc Short circuit current SVR eN IO = 0 mA, VI = 4.9 to 18V, TJ = 25°C VI - VO = 5V 3.2 4.5 A VI - VO = 25V 0.2 0.5 A Thermal regulation TA = 25°C, 30ms pulse Supply voltage rejection f = 120 Hz, CO = 25µF, IO = 3A VI = 8.3 ± 3V RMS Output noise voltage (% of TA = 25°C, f =10Hz to 10KHz VO) S Temperature stability S Long term stability TA = 125°C, 1000Hrs 0.008 60 0.04 %/W 72 dB 0.003 % 0.5 % 0.5 % 1. See short-circuit current curve for available output current at fixed dropout. 9/27 Electrical characteristics Table 7. Symbol LD1085 series Electrical characteristics of LD1085#50 (VI=8V, CI = CO =10μF, TA = -40 to 125°C, unless otherwise specified). Parameter Test Min. Typ. Max. Unit IO = 0 mA, TJ = 25°C 4.95 5 5.05 V IO = 0 to 3A, VI = 6.6 to 30V 4.9 5 5.1 V 0.5 10 mV IO = 0 mA, VI = 6.6 to 20V 1 10 mV IO = 0 to 3A, TJ = 25°C 5 10 mV IO = 0 to 3A 10 35 mV VO Output voltage (1) ΔVO Line regulation ΔVO Load regulation Vd Dropout voltage IO = 3A 1.3 1.5 V Iq Quiescent current VI ≤30V 5 10 mA Isc Short circuit current SVR eN IO = 0 mA, VI = 6.6 to 20V, TJ = 25°C VI - VO = 5V 3.2 4.5 A VI - VO = 25V 0.2 0.5 A Thermal regulation TA = 25°C, 30ms pulse Supply voltage rejection f = 120 Hz, CO = 25µF, IO = 3A VI = 10 ± 3V RMS Output noise voltage (% of TA = 25°C, f =10Hz to 10KHz VO) S Temperature stability S Long term stability TA = 125°C, 1000Hrs 1. See short-circuit current curve for available output current at fixed dropout. 10/27 0.008 60 0.04 %/W 72 dB 0.003 % 0.5 % 0.5 % LD1085 series Table 8. Symbol Electrical characteristics Electrical characteristics of LD1085#12 (VI=15V, CI = CO =10μF, TA = -40 to 125°C, unless otherwise specified). Parameter VO Output voltage (1) ΔVO Line regulation Test Min. Typ. Max. Unit IO = 0 mA, TJ = 25°C 11.88 12 12.12 V IO = 0 to 3A, VI = 13.8 to 30V 11.76 12 12.24 V IO = 0 mA, VI = 13.8 to 25V, TJ = 25°C 1 25 mV IO = 0 mA, VI = 13.8 to 25V 2 25 mV IO = 0 to 3A, TJ = 25°C 12 36 mV IO = 0 to 3A 24 72 mV ΔVO Load regulation Vd Dropout voltage IO = 3A 1.3 1.5 V Iq Quiescent current VI ≤30V 5 10 mA Isc Short circuit current SVR eN VI - VO = 5V 3.2 4.5 A VI - VO = 25V 0.2 0.5 A Thermal regulation TA = 25°C, 30ms pulse Supply voltage rejection f = 120 Hz, CO = 25µF, IO = 3A VI = 17 ± 3V RMS Output noise voltage (% of TA = 25°C, f =10Hz to 10KHz VO) S Temperature stability S Long term stability TA = 125°C, 1000Hrs 0.008 54 0.04 %/W 66 dB 0.003 % 0.5 % 0.5 % 1. See short-circuit current curve for available output current at fixed dropout. 11/27 Electrical characteristics Table 9. Symbol LD1085 series Electrical characteristics of LD1085# (VI=4.25V, CI = CO =10μF, TA = -40 to 125°C, unless otherwise specified). Parameter VO Output voltage (1) ΔVO Line Regulation Test Min. Typ. Max. Unit IO = 10mA TJ = 25°C 1.237 1.25 1.263 V IO = 10mA to 3A, VI = 2.85 to 30V 1.225 1.25 1.275 V IO = 10mA, VI = 2.85 to 16.5V, TJ = 25°C 0.015 0.2 % IO = 10mA, VI = 2.85 to 16.5V 0.035 0.2 % IO = 10mA to 3A, TJ = 25°C 0.1 0.3 % IO = 0 to 3A 0.2 0.4 % ΔVO Load Regulation Vd Dropout Voltage IO = 3A 1.3 1.5 V Minimum Load Current VI = 30V 3 10 mA IO(min) Isc Short Circuit Current VI - VO = 5V 5.5 6.5 A VI - VO = 25V 0.5 0.7 A Thermal Regulation TA = 25°C, 30ms pulse SVR Supply Voltage Rejection f = 120 Hz, CO = 25µF,CADJ = 25 µF, IO = 3A, VI = 6.25 ± 3V IADJ Adjust Pin Current ΔIADJ eN Adjust Pin Current Change (1) RMS Output Noise Voltage (% of VO) S Temperature Stability S Long Term Stability 60 72 %/W dB VI = 4.25V, IO = 10 mA 55 120 μA IO = 10mA to 3A, VI = 2.85 to 16.5V 0.2 5 μA TA = 25°C, f =10Hz to 10KHz TA = 125°C, 1000Hrs 1. See short-circuit current curve for available output current at fixed dropout. 12/27 0.003 0.015 0.003 % 0.5 % 0.5 % LD1085 series Typical application 5 Typical application Figure 3. (Unless otherwise specified TJ = 25°C, CI = CO = 10µF) Output voltage vs temperature Figure 4. Output voltage vs temperature Figure 5. Output voltage vs temperature Figure 6. Short circuit current vs dropout voltage Figure 7. Line regulation vs temperature Figure 8. Load regulation vs temperature 13/27 Typical application Figure 9. Dropout voltage vs temperature LD1085 series Figure 10. Dropout voltage vs output current Figure 11. Adjust pin current vs temperature Figure 12. Quiescent current vs temperature Figure 13. Line regulation vs temperature Figure 14. Supply voltage rejection vs output current 14/27 LD1085 series Typical application Figure 15. Supply voltage rejection vs frequency Figure 16. Supply voltage rejection vs temperature Figure 17. Minimum load current vs temperature Figure 18. Stability Figure 19. Stability Figure 20. Line transient VI=12 to 13V, IO=200mA, CI = 1µF(tant), CO=10µF(tant), CADJ=1µF 15/27 Typical application LD1085 series Figure 21. Line transient Figure 22. Load transient VI=12 to 13V, IO=200mA, CI = 1µF(tant), CO=10µF(tant), CADJ=1µF VI=12V, IO=0.12 to 3A, CI = 1µF(tant), CO=10µF(tant), CADJ=1µF Figure 23. Load transient VI=12V, IO=0.12 to 3A, CI = 1µF(tant), CO=10µF(tant), CADJ=1µF 16/27 LD1085 series 6 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 17/27 Package mechanical data LD1085 series TO-220 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 D1 1.27 0.107 0.050 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.067 F2 1.14 1.70 0.044 0.067 G 4.95 5.15 0.194 0.203 G1 2.4 2.7 0.094 0.106 H2 10.0 10.40 0.393 0.409 14.0 0.511 L2 L4 16.4 13.0 0.645 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.2 6.6 0.244 0.260 L9 3.5 3.93 0.137 0.154 DIA. 3.75 3.85 0.147 0.151 P011C 18/27 LD1085 series Package mechanical data TO-220FP MECHANICAL DATA mm. DIM. MIN. TYP inch MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.50 0.045 0.059 F2 1.15 1.50 0.045 0.059 G 4.95 5.2 0.194 0.204 G1 2.4 2.7 0.094 0.106 H 10.0 10.40 0.393 L2 16 0.409 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 0.385 0.417 L5 2.9 3.6 0.114 0.142 L6 15.9 16.4 0.626 0.645 L7 9 9.3 0.354 0.366 DIA. 3 3.2 0.118 0.126 7012510A-H 19/27 Package mechanical data LD1085 series DPAK MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A A1 A2 B b4 2.2 0.9 0.03 0.64 5.2 2.4 1.1 0.23 0.9 5.4 0.086 0.035 0.001 0.025 0.204 0.094 0.043 0.009 0.035 0.212 C C2 D D1 E E1 0.45 0.48 6 0.6 0.6 6.2 0.017 0.019 0.236 0.023 0.023 0.244 6.6 0.252 e e1 H L (L1) L2 L4 R V2 5.1 6.4 0.200 4.7 2.28 4.4 9.35 1 0.090 4.6 10.1 0.173 0.368 0.039 2.8 0.8 0.6 0.181 0.397 0.110 0.031 1 0.023 0.2 0° 0.260 0.185 0.039 0.008 8° 0° 8° 0068772-F 20/27 LD1085 series Package mechanical data D2PAK MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.4 4.6 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 D1 E 8 10 E1 0.368 0.315 10.4 0.393 8.5 0.409 0.335 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.624 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 R V2 0.4 0˚ 0.126 0.016 8˚ 0˚ 8˚ P011P6G 21/27 Package mechanical data LD1085 series D2PAK/A MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.028 0.037 B1 0.8 1.3 0.031 0.051 B2 1.14 1.7 0.045 0.067 C 0.45 0.60 0.018 0.024 C2 1.23 1.36 0.048 0.054 D 8.95 9.35 0.352 0.368 D1 E 8 10 E1 0.315 10.4 0.394 8.5 0.409 0.335 G 4.88 5.28 0.192 L 15 15.85 0.591 0.624 L2 1.27 1.4 0.050 0.055 M 2.4 3.2 0.094 R V2 0.4 0° 0.208 0.126 0.016 8° 0° 8° 7106164/D 22/27 LD1085 series Package mechanical data Tape & Reel DPAK-PPAK MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. 330 13.0 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 MAX. 0.504 0.512 22.4 0.519 0.882 Ao 6.80 6.90 7.00 0.268 0.272 0.2.76 Bo 10.40 10.50 10.60 0.409 0.413 0.417 Ko 2.55 2.65 2.75 0.100 0.104 0.105 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 7.9 8.0 8.1 0.311 0.315 0.319 23/27 Package mechanical data LD1085 series Tape & Reel D2PAK-P 2PAK-D 2PAK/A-P 2PAK/A MECHANICAL DATA mm. inch DIM. MIN. TYP A MIN. TYP. 180 13.0 13.2 MAX. 7.086 C 12.8 D 20.2 0.795 N 60 2.362 T 24/27 MAX. 0.504 0.512 14.4 0.519 0.567 Ao 10.50 10.6 10.70 0.413 0.417 0.421 Bo 15.70 15.80 15.90 0.618 0.622 0.626 Ko 4.80 4.90 5.00 0.189 0.193 0.197 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 11.9 12.0 12.1 0.468 0.472 0.476 LD1085 series Order codes 7 Order codes Table 10. Order codes Part numbers Packages TO-220 TO-220FP D2 PAK DPAK (T&R) 2 D PAK/A 2 D PAK/A (T&R) LD1085DT15R Output voltage 1.5 V LD1085V18 LD1085DT18R LD1085D2M18R 1.8 V LD1085V25 LD1085DT25R LD1085D2M25R 2.5 V LD1085DT33R LD1085D2M33R 3.3 V LD1085V33 LD1085D2T33 LD1085V50 LD1085D2M50 5.0 V LD1085V12 LD1085D2M12 LD1085D2M12R 12.0 V LD1085V LD1085P LD1085D2T LD1085DT-R LD1085CDT-R LD1085D2M LD1085D2M-R ADJ ADJ 25/27 Revision history LD1085 series 8 Revision history Table 11. Revision history Date Revision 07-Oct-2004 12 Mistake Order Codes - Table 1. 08-Feb-2005 13 Mistake U.M. Load Regulation - V ==> mV. 01-Mar-2005 14 Version 1.2V removed. 22-May-2006 15 Order Codes has been updated and new template. 10-Nov-2006 16 Add package DPAK, typo on VO test value in tables 3, 4 and 11. 04-Apr-2007 17 Order codes has been updated. 07-Jun-2007 18 Order codes has been updated. 26/27 Changes LD1085 series Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 27/27