1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/15-1250(C)-T(3)-SSC2A Features • Diplexer Single Mode Single Fiber 1x9 SC Receptacle Connector • Wavelength Tx 1310 nm/Rx 1530 nm • IEEE 802.3 Compliant • Single +5V Power Supply [B-13/15-1250(C)-T-SSC2A] • Single +3.3V power Supply [B-13/15-1250(C)-T3-SSC2A] • PECL/LVPECL Differential Inputs and Output [B-13/15-1250-T(3)-SSC2A] • TTL/LVTTL Signal Detection Output Optional [B-13/15-1250C-T(3)-SSC2A] • Wave Solderable and Aqueous Washable • LED Multisourced 1x9 Transceiver Interchangeable • Class 1 Laser Int. Safety Standard IEC 825 Compliant • Uncooled Laser diode with MQW structure • Complies with Telcordia (Bellcore) GR-468-CORE • Temperature Range: -40 to 85ºC • Optical Isolation > 30 dB • Cross Talk < -33 dB Absolute Maximum Rating Parameter Symbol Min. Max. Unit Power Supply Voltage Vcc 0 6 V B-13/15-1250(C)-T-SSC2A Power Supply Voltage Vcc 0 3.6 V B-13/15-1250(C)-T3-SSC2A - 0 Vcc V Iout - 30 mA - - 260 ºC Tstg -40 85 ºC Input Voltage Output Current Soldering Temperature Storage Temperature Note 10 seconds on leads only Recommended Operating Condition Parameter Symbol Min. Typ. Max. Unit Power Supply Voltage Vcc 4.75 5 5.25 V Power Supply Voltage Vcc 3.1 3.3 3.5 V Operating Temperature (Case) Topr -40 - 85 ºC - - 155 - Mbps Data Rate Transmitter Specifications (Optical) Parameter Optical Transmit Power Symbol Min Typical Max Unit Po -5 - +0 dBm λ 1260 1310 1360 nm Output Spectrum Width ∆λ - - 3 dB Extinction Ratio ER 9 - - dB Output center Wavelength Output Eye Notes Output power is coupled into a 9/125 µm single mode fiber RMS (σ) Compliant with IEEE 802.3 Optical Rise Time Tr - - 0.26 ns 20% to 80% Values Optical Fall Time Tf - - 0.26 ns 20% to 80% Values Tx:1310 nm/ Rx:1530 nm Optical Isolation Relative Intensity Noise Total Jitter LUMINENTOIC.COM - 30 - - dB RIN - - -116 dB/Hz TJ - - 0.27 ns Measured with 27-1 PRBS 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS899-Nov0405 Rev A.0 1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/15-1250(C)-T(3)-SSC2A Transmitter Specifications (Electrical) Parameter Symbol Min Typical Max Unit Power Supply Current ICC - - 160 mA Data Input Current-Low IIL -350 - - µA Data Input Current-High IIH - - 350 µA Differential Input Voltage VIH-VIL 300 - - mV Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V Symbol Min Typical Max Unit Notes Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs Receiver Specifications (Optical) Parameter Sensitivity Notes PRBS, BER = 10-12 - - - -20 dBm Maximum Input Power Pin 0 - - dBm Signal Detect-Asserted Pa - - -20 dBm Measured on transition: low to high(Note1) Signal Detect-Deasserted Pd -35 - - dBm Measured on transition: high to low(Note1) 1.0 - - dB - - -33 dB 1480 - 1600 nm Max Unit Signal Detect-Hysteresis - Cross Talk Wavelength of Operation Measured with 27-1 Note 1: The SD level should be deasserted when fiber disconnected Receiver Specifications (Electrical) Parameter Symbol Power Supply Current Min Typical ICC - - 100 mA Data output Voltage-Low VOL -Vcc -2.0 - -1.58 V Data output Voltage-High VOH- Vcc -1.1 - -0.74 V Signal Detect output Voltge-Low VSDL-Vcc -2.0 - -1.58 V Signal Detect Output Voltge-High VSDH- Vcc -1.1 - -0.74 V Signal Detect output Voltge-Low V SDL - - 0.5 V Signal Detect Output Voltge-High V SDH -20 - - V LUMINENTOIC.COM Note The current excludes the output load current These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs B-13/15-1250-T(3)-SSC2A B-13/15-1250C-T(3)-SSC2A 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS899-Nov0405 Rev A.0 1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/15-1250(C)-T(3)-SSC2A Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TX-) 8. (TX+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN Symbol Notes 1 RxGND Directly connect this pin to the receiver ground plane 2 RD+ See recommended circuit schematic 3 RD- See recommended circuit schematic 4 SD 5 RxVcc DC power for the receiver section 6 TxVcc DC power for the transmitter section 7 TD- See recommended circuit schematic 8 Warnings TD+ See recommended circuit schematic 9 LUMINENTOIC.COM Active high on this indicates a received optical signal TxGND Directly connect this pin to the transmitter ground plane 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS899-Nov0405 Rev A.0 1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/15-1250(C)-T(3)-SSC2A Recommended Circuit Schematic (PECL SD) B-13/15-1250-T(3)-SSC2A Tx Vcc C5 Rx Vcc 9 R1 7 8 6 5 4 3 2 1 R3 R9 R5 C6 R7 TD + RD + TD - RD - Tx Vcc SD Rx Vcc R2 R4 Notes +3.3V: R1=R3=R5=R7=R9=130 R2=R4=R6=R8=R10=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H No internal connection No internal connection Transceiver Top view R10 R6 R8 L1 Notes +5V: R1=R3=R5=R7=R9=82 R2=R4=R6=R8=R10=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Vcc C1 C3 L2 C2 C4 Rx Vcc Tx Vcc Recommended Circuit Schematic (TTL SD) B-13/15-1250C-T(3)-SSC2A Tx Vcc C5 Rx Vcc 9 R1 7 8 6 5 4 3 2 1 R5 R3 C6 R7 RD + TD + RD - TD - Tx Vcc SD Rx Vcc R2 R4 Notes +3.3V: R1=R3=R5=R7=130 R2=R4=R6=R8=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H No internal connection R6 No internal connection Transceiver Top view R8 L1 Notes +5V: R1=R3=R5=R7=82 R2=R4=R6=R8=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Vcc C3 C1 L2 C4 C2 Rx Vcc Tx Vcc The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS899-Nov0405 Rev A.0 1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/15-1250(C)-T(3)-SSC2A Package Diagram Top View Front View Rear View Side View LUMINENTOIC.COM Units: mm 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS899-Nov0405 Rev A.0 1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/15-1250(C)-T(3)-SSC2A Ordering Information Available Options: B-13/15-1250-T-SSC2A B-13/15-1250-T3-SSC2A B-13/15-1250C-T-SSCA2A B-13/15-1250C-T3-SSC2A Part numbering Definition: B - 13/15 - 1250(C) - T(3) - S SC Tx Power Temperature range • Wavelength Tx Wavelength=1310nm Rx Wavelength=1530nm • Communication protocol (1250 Gbps) • T = +5 V Transceiver T3 = +3.3V Transceiver • Single mode fiber • Connector options • Tx Power 2 = -5 to 0 dBm • Temperature range A = industrial temperature(-40 to 85 ºC) Warnings Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notice IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS899-Nov0405 Rev A.0