/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 Metallized Polyester Film Capacitors (MKT) Uncoated (Silver Caps) Extremely small dimensions Versions with special dimensions can be supplied at short notice B 32 560 … B 32 564 Cut surfaces Construction ● Dielectric: polyethylene terephthalate (polyester) ● Stacked-film technology ● Uncoated Dimensions in mm Features ● Special dimensions available upon request ● High pulse strength ● Minimum tensile strength of leads >10 N Typical applications ● ● ● ● Standard applications Electronic lamp ballast circuits Energy-saving lamps Substitute for electrolytics in electronic lamp ballasts (420 Vdc) Lead spacing ± 0,4 7,5 10,0 15,0 22,5 27,5 Diameter d1 Type 0,5 0,5 0,6 0,8 0,8 B 32 560 B 32 561 B 32 562 B 32 563 B 32 564 Terminals ● Parallel wire leads, tinned ● Also available with (3,0 ± 0,5) mm lead length upon request Marking Rated capacitance (coded), rated dc voltage Delivery mode Bulk (untaped) Taped (AMMO pack or reel) for lead spacing ≤ 15,0 mm. For notes on taping, refer to page 279. Detail specification Homologated in accordance with CECC 30 401-007 Notes on mounting When mounting these capacitors, take into account creepage distances and clearances to adjacent live parts. The insulating strength of the cut surfaces to other live parts of the circuit is 1,5 times the capacitors rated dc voltage, but is always at least 300 Vdc. Capacitors with 7,5 mm lead spacing are only suitable for use with single-clad printed circuit boards. Siemens Matsushita Components 53 B 32 560 … B 32 564 MKT Overview of available types 15 mm 22,5 mm 27,5 mm B 32 561 57 B 32 562 58 B 32 563 59 B 32 564 60 1) For B 32 564, 420 Vdc only 54 Siemens Matsushita Components /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 400 Vdc 420 Vdc 100 Vdc 250 Vdc 400 Vdc 250 Vdc 100 Vdc 100 Vdc 250 Vdc 630 Vdc 250 Vdc 100 Vdc 400 Vdc 400 Vdc 400 Vdc 630 Vdc 10 mm 250 Vdc 63 Vdc 100 Vdc Lead 7,5 mm spacing Type B 32 560 Page 55 1,0 nF 1,5 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 0,10 µF 0,15 µF 0,22 µF 0,33 µF 0,47 µF 0,68 µF 1,0 µF 1,5 µF 2,2 µF 3,3 µF 4,7 µF 5,6 µF1) 6,8 µF 10 µF 15 µF 22 µF 33 µF /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 B 32 560 MKT 7,5 Ordering codes and packing units, lead spacing 7,5 mm VR (Vrms, f ≤ 60 Hz) CR 63 Vdc (40 Vac) 0,22 µF 2,5 × 5,2 × 9,0 0,33 µF 2,5 × 5,6 × 9,0 0,47 µF 2,6 × 5,8 × 9,0 0,68 µF 3,2 × 6,2 × 9,0 1,0 µF 4,0 × 6,8 × 9,0 1,5 µF 5,1 × 7,6 × 9,0 2,2 µF 6,5 × 8,2 × 9,0 3,3 µF 8,5 × 9,1 × 9,0 4,7 µF 9,8 × 11,0 × 9,0 6,8 µF 11,5 × 13,3 × 9,0 0,10 µF 2,5 × 4,7 × 9,0 0,15 µF 2,5 × 4,7 × 9,0 0,22 µF 2,5 × 5,1 × 9,0 0,33 µF 2,7 × 5,7 × 9,0 0,47 µF 3,4 × 6,1 × 9,0 0,68 µF 4,2 × 6,5 × 9,0 1,0 µF 5,5 × 7,0 × 9,0 1,5 µF 6,7 × 8,2 × 9,0 2,2 µF 8,5 × 9,2 × 9,0 33 nF 2,5 × 4,8 × 9,0 47 nF 2,5 × 5,2 × 9,0 68 nF 2,6 × 5,7 × 9,0 0,10 µF 3,2 × 6,1 × 9,0 0,15 µF 3,9 × 7,0 × 9,0 0,22 µF 4,9 × 7,5 × 9,0 0,33 µF 6,4 × 8,2 × 9,0 100 Vdc (63 Vac) 250 Vdc (160 Vac) Maximum dimensions b × h × l (mm) Ordering code1) B32560-J224-+ B32560-J334-+ B32560-J474-+*** B32560-J684-+*** B32560-J105-+*** B32560-J155-+*** B32560-J225-+*** B32560-J335-+ B32560-J475-+ B32560-J685-+ B32560-J1104-+ B32560-J1154-+ B32560-J1224-+*** B32560-J1334-+*** B32560-J1474-+*** B32560-J1684-+*** B32560-J1105-+*** B32560-J1155-+ B32560-J1225-+ B32560-J3333-+ B32560-J3473-+*** B32560-J3683-+*** B32560-J3104-+*** B32560-J3154-+*** B32560-J3224-+*** B32560-J3334-+ Packing units (pcs) Ammo Reel pack 2) 2) 2) 2) 3250 2850 2200 1700 1300 – – – 2600 2300 1800 1400 1100 – – – 2) 2) 2) 2) 3400 3100 2500 2000 1600 – – 2700 2500 2000 1600 1300 – – 2) 2) 3500 3400 2650 2150 1750 – 2800 2700 2200 1800 1400 – Untaped 2500 2500 2000 1500 1000 500 500 350 250 150 3000 3000 2000 1500 1200 1000 500 400 300 3000 2300 1700 1200 1000 650 500 Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J Special dimensions available upon request. For corresponding design rules, refer to page 238. 1) Replace the + by the code letter for the required capacitance tolerance. Replace the *** by the code number for the required packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. 2) Taping upon request Siemens Matsushita Components 55 B 32 560 MKT 7,5 Ordering codes and packing units, lead spacing 7,5 mm CR 400 Vdc (200 Vac) 1,0 nF 1,5 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 0,10 µF 0,15 µF 1,0 nF 1,5 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF 630 Vdc (400 Vac) Maximum dimensions b × h × l (mm) Ordering code1) 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,6 × 6,0 × 9,0 3,2 × 6,5 × 9,0 3,8 × 7,3 × 9,0 4,9 × 7,7 × 9,0 6,5 × 8,2 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 3,2 × 6,5 × 9,0 3,8 × 7,5 × 9,0 B32560-J6102-+ B32560-J6152-+*** B32560-J6222-+*** B32560-J6332-+*** B32560-J6472-+*** B32560-J6682-+*** B32560-J6103-+*** B32560-J6153-+*** B32560-J6223-+*** B32560-J6333-+*** B32560-J6473-+*** B32560-J6683-+*** B32560-J6104-+*** B32560-J6154-+ B32560-J8102-+ B32560-J8152-+*** B32560-J8222-+*** B32560-J8332-+*** B32560-J8472-+*** B32560-J8682-+*** B32560-J8103-+*** Packing units (pcs) Ammo Reel pack 2) 2) 3500 3700 3400 3700 3700 3500 3500 3400 3400 2650 2250 1750 – 2900 3000 2800 3000 3000 2800 2800 2700 2700 2200 1900 1400 – 2) 2) 3500 3700 3400 3400 2900 2400 2900 3000 2800 2700 2400 2000 Untaped 2300 2000 2100 2000 2000 2000 2200 2500 2300 1600 1200 1000 500 500 2300 2000 2100 2000 1800 1300 1000 Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J Special dimensions available upon request. For corresponding design rules, refer to page 238. 1) Replace the + by the code letter for the required capacitance tolerance. Replace the *** by the code number for the required packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. 2) Taping upon request 56 Siemens Matsushita Components /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 VR (Vrms, f ≤ 60 Hz) /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 B 32 561 MKT 10 Ordering codes and packing units, lead spacing 10 mm VR (Vrms, f ≤ 60 Hz) CR 100 Vdc (63 Vac) 0,33 µF 0,47 µF 0,68 µF 1,0 µF 1,5 µF 2,2 µF 47 nF 68 nF 0,10 µF 0,15 µF 0,22 µF 0,33 µF 0,47 µF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 0,10 µF 0,15 µF 0,22 µF 250 Vdc (160 Vac) 400 Vdc (200 Vac) Maximum dimensions b × h × l (mm) Ordering code1) 2,5 × 5,2 × 11,5 2,9 × 5,8 × 11,5 3,6 × 6,3 × 11,5 4,5 × 6,9 × 11,5 5,6 × 7,8 × 11,5 6,9 × 9,0 × 11,5 2,5 × 4,4 × 11,5 2,5 × 4,8 × 11,5 2,8 × 5,3 × 11,5 3,3 × 6,0 × 11,5 4,2 × 6,6 × 11,5 5,2 × 7,5 × 11,5 6,3 × 8,5 × 11,5 2,5 × 5,1 × 11,5 2,5 × 5,1 × 11,5 2,5 × 5,1 × 11,5 2,5 × 5,1 × 11,5 2,6 × 6,0 × 11,5 3,2 × 6,6 × 11,5 4,0 × 6,9 × 11,5 5,2 × 7,7 × 11,5 6,6 × 8,5 × 11,5 B32561-J1334-+*** B32561-J1474-+*** B32561-J1684-+*** B32561-J1105-+*** B32561-J1155-+*** B32561-J1225-+ B32561-J3473-+ B32561-J3683-+*** B32561-J3104-+*** B32561-J3154-+*** B32561-J3224-+*** B32561-J3334-+*** B32561-J3474-+*** B32561-J6103-+*** B32561-J6153-+*** B32561-J6223-+*** B32561-J6333-+*** B32561-J6473-+*** B32561-J6683-+*** B32561-J6104-+*** B32561-J6154-+*** B32561-J6224-+ Packing units (pcs) Ammo Reel pack 1750 2400 1560 2300 1260 2000 1050 1500 810 1200 – – 2) 2) 1760 1600 1300 1040 850 700 1760 1830 1830 1760 1760 1390 1090 850 – 2400 2300 2000 1600 1300 1000 2400 2500 2500 2400 2400 2100 1700 1300 – Untaped 1600 1200 1000 500 500 400 2300 1800 1300 1000 700 500 400 1700 2000 2000 1700 1300 1000 700 500 300 Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J Special dimensions available upon request. For corresponding design rules, refer to page 238. 1) Replace the + by the code letter for the required capacitance tolerance. Replace the *** by the code number for the required packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. 2) Taping upon request Siemens Matsushita Components 57 B 32 562 MKT 15 Ordering codes and packing units, lead spacing 15 mm CR 100 Vdc (63 Vac) 1,0 µF 1,5 µF 2,2 µF 3,3 µF 4,7 µF 6,8 µF 10 µF 0,22 µF 0,33 µF 0,47 µF 0,68 µF 1,0 µF 1,5 µF 2,2 µF 3,3 µF 22 nF 33 nF 47 nF 68 nF 0,10 µF 0,15 µF 0,22 µF 0,33 µF 0,47 µF 0,68 µF 1,0 µF 0,10 µF 0,15 µF 0,22 µF 0,33 µF 0,47 µF 250 Vdc (160 Vac) 400 Vdc (200 Vac) 630 Vdc (350 Vac) Maximum dimensions b × h × l (mm) Ordering code1) 3,2 × 6,3 × 16,5 4,0 × 7,3 × 16,5 4,9 × 8,0 × 16,5 6,0 × 9,3 × 16,5 7,3 × 10,6 × 16,5 9,0 × 11,8 × 16,5 11,8 × 13,0 × 16,5 3,2 × 5,6 × 16,5 4,0 × 6,2 × 16,5 5,0 × 6,7 × 16,5 6,0 × 7,8 × 16,5 7,0 × 9,3 × 16,5 8,7 × 11,0 × 16,5 10,7 × 12,8 × 16,5 13,9 × 14,5 × 16,5 3,3 × 5,6 × 16,5 3,3 × 5,6 × 16,5 3,3 × 5,6 × 16,5 3,3 × 5,6 × 16,5 3,3 × 5,6 × 16,5 3,9 × 6,5 × 16,5 4,7 × 7,5 × 16,5 6,0 × 8,3 × 16,5 7,3 × 9,3 × 16,5 8,9 × 10,8 × 16,5 10,9 × 12,5 × 16,5 6,2 × 9,3 × 16,5 7,6 × 10,8 × 16,5 9,2 × 12,2 × 16,5 11,2 × 14,2 × 16,5 13,5 × 16,3 × 16,5 B32562-J1105-+*** B32562-J1155-+*** B32562-J1225-+*** B32562-J1335-+*** B32562-J1475-+*** B32562-J1685-+*** B32562-J1106-+ B32562-J3224-+*** B32562-J3334-+*** B32562-J3474-+*** B32562-J3684-+*** B32562-J3105-+*** B32562-J3155-+*** B32562-J3225-+ B32562-J3335-+ B32562-J6223-+*** B32562-J6333-+*** B32562-J6473-+*** B32562-J6683-+*** B32562-J6104-+*** B32562-J6154-+*** B32562-J6224-+*** B32562-J6334-+*** B32562-J6474-+*** B32562-J6684-+*** B32562-J6105-+ B32562-J8104-+ B32562-J8154-+ B32562-J8224-+ B32562-J8334-+ B32562-J8474-+ Packing units (pcs) Ammo Reel pack 1750 2000 1460 1500 1190 1300 960 1000 790 900 640 700 – – 1750 2000 1460 1500 1190 1300 960 1000 830 900 660 700 – – – – 1750 2000 1750 2000 1870 2100 1800 2000 1700 1900 1420 1600 1240 1300 960 1000 790 900 640 700 – – – – – – – – – – – – Untaped 1500 1000 800 500 400 290 200 1700 1200 950 500 500 300 200 150 1800 1800 1800 1800 1600 1200 850 500 450 300 200 700 500 350 250 180 Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J Special dimensions available upon request. For corresponding design rules, refer to page 238. 1) Replace the + by the code letter for the required capacitance tolerance. Replace the *** by the code number for the required packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. 58 Siemens Matsushita Components /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 VR (Vrms, f ≤ 60 Hz) /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 B 32 563 MKT 22,5 Ordering codes and packing units, lead spacing 22,5 mm VR (Vrms, f ≤ 60 Hz) 100 Vdc (63Vac) 250 Vdc (160 Vac) 400 Vdc (200Vac) CR 1,5 µF 2,2 µF 3,3 µF 4,7 µF 6,8 µF 10 µF 15 µF 22 µF 0,68 µF 1,0 µF 1,5 µF 2,2 µF 3,3 µF 4,7 µF 0,22 µF 0,33 µF 0,47 µF 0,68 µF 1,0 µF 1,5 µF 2,2 µF Maximum dimensions b × h × l (mm) 5,0 × 8,0 × 24,0 5,0 × 8,2 × 24,0 5,0 × 8,2 × 24,0 5,9 × 9,0 × 24,0 7,0 × 10,5 × 24,0 8,6 × 12,2 × 24,0 10,9 × 14,0 × 24,0 12,8 × 17,2 × 24,0 4,8 × 7,2 × 24,0 5,6 × 8,2 × 24,0 6,9 × 9,5 × 24,0 8,3 × 11,2 × 24,0 10,1 × 13,5 × 24,0 12,2 × 15,5 × 24,0 5,1 × 8,0 × 24,0 5,1 × 8,0 × 24,0 5,7 × 8,3 × 24,0 6,9 × 9,6 × 24,0 8,3 × 11,2 × 24,0 10,3 × 13,2 × 24,0 12,6 × 15,5 × 24,0 Ordering code1) Packing units (pcs) Untaped B32563-J1155-+ B32563-J1225-+ B32563-J1335-+ B32563-J1475-+ B32563-J1685-+ B32563-J1106-+ B32563-J1156-+ B32563-J1226-+ B32563-J3684-+ B32563-J3105-+ B32563-J3155-+ B32563-J3225-+ B32563-J3335-+ B32563-J3475-+ B32563-J6224-+ B32563-J6334-+ B32563-J6474-+ B32563-J6684-+ B32563-J6105-+ B32563-J6155-+ B32563-J6225-+ 1400 1900 1900 1600 920 960 620 360 1760 1140 920 740 700 390 1800 1700 1660 920 850 660 360 Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J Special dimensions available upon request. For corresponding design rules, refer to page 238. 1) Replace the + by the code letter for the required capacitance tolerance. Siemens Matsushita Components 59 B 32 564 MKT 27,5 VR (Vrms , f ≤ 60 Hz) 100 Vdc (63Vac) 250 Vdc (160 Vac) 400 Vdc (200 Vac) 420 Vdc (200 Vac) CR 4,7 µF 6,8 µF 10 µF 15 µF 22 µF 33 µF 1,0 µF 1,5 µF 2,2 µF 3,3 µF 4,7 µF 6,8 µF 10 µF 1,0 µF 1,5 µF 2,2 µF 3,3 µF 4,7 µF 4,7 µF 5,6 µF 6,8 µF Maximum dimensions b × h × l (mm) 5,6 × 8,3 × 29,0 6,3 × 9,5 × 29,0 7,6 × 11,0 × 29,0 9,1 × 13,5 × 29,0 11,0 × 16,0 × 29,0 13,0 × 19,8 × 29,0 5,1 × 7,6 × 29,0 5,3 × 10,2 × 29,0 6,4 × 11,8 × 29,0 7,9 × 14,0 × 29,0 9,6 × 15,8 × 29,0 11,9 × 18,0 × 29,0 13,8 × 22,5 × 29,0 6,8 × 11,2 × 29,0 7,8 × 14,2 × 29,0 9,6 × 16,4 × 29,0 12,2 × 18,8 × 29,0 14,2 × 22,8 × 29,0 16,0 × 20,0 × 29,0 16,0 × 20,0 × 29,0 16,0 × 20,0 × 29,0 Ordering code1) Packing units (pcs) Untaped B32564-J1475-+ B32564-J1685-+ B32564-J1106-+ B32564-J1156-+ B32564-J1226-+ B32564-J1336-+ B32564-J3105-+ B32564-J3155-+ B32564-J3225-+ B32564-J3335-+ B32564-J3475-+ B32564-J3685-+ B32564-J3106-+ B32564-J6105-+ B32564-J6155-+ B32564-J6225-+ B32564-J6335-+ B32564-J6475-+ B32564-T6475-K B32564-T6565-K B32564-T6685-K 1000 820 680 430 320 360 1620 970 920 750 400 300 280 750 750 400 330 260 290 290 290 Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J Special dimensions available upon request. For corresponding design rules, refer to page 238. 1) Replace the + by the code letter for the required capacitance tolerance. 60 Siemens Matsushita Components /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 Ordering codes and packing units, lead spacing 27,5 mm /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 B 32 560 … B 32 564 MKT Technical data Climatic category in accordance with IEC 68-1 Lower category temperature Tmin Upper category temperature Tmax Damp heat test Limit values after damp heat test1) Reliability: Reference conditions Failure rate Service life Failure criteria: Total failure Failure due to variation of parameters DC test voltage Category voltage VC Operation with dc voltage or ac voltage Vrms up to 60 Hz Category voltage for short operating periods Dissipation factor tan δ (in 10−3) at 20 °C (upper limit values) Insulation resistance Ris or time constant τ = CR ⋅ Ris at 20 °C, rel. humidity ≤ 65 % (minimum as-delivered values) 55/100/561) − 55 °C + 100 °C (+ 125 °C for 1000 h and VC = 0,5 ⋅ VR) 56 days/40 °C/93 % relative humidity Capacitance change |∆C/C| ≤5% Dissipation factor change ∆ tan δ ≤ 3 ⋅ 10−3 (at 1 kHz) ≤ 5 ⋅ 10−3 (at 10 kHz) Insulation resistance Ris ≥ 50 % of minimum or time constant τ = CR ⋅ Ris as-delivered values 0,5 ⋅ VR; 40 °C 2 ⋅10−9/h = 2 fit For a conversion table for other operating conditions and temperatures, refer to page 276. 200 000 h Short circuit or open circuit Capacitance change |∆C/C| > 10 % Dissipation factor tan δ > 2 ⋅ upper limit value Insulation resistance Ris < 150 MΩ (CR ≤ 0,33 µF) or time constant τ = CR ⋅ Ris < 50 s (CR > 0,33 µF) 1,4 ⋅ VR, 2 s T ≤ 85 °C: VC = 1,0 ⋅ VR or 1,0 ⋅ Vrms T ≤ 100 °C: VC = 0,8 ⋅ VR or 0,8 ⋅ Vrms T ≤ 100 °C: VC = 1,25 ⋅ VR or 1,0 ⋅ Vrms for max. 2000 h T ≤ 125 °C: VC = 0,5 ⋅ VR or 0,5 ⋅ Vrms for max. 1000 h at 1 kHz 10 kHz 100 kHz VR ≤ 100 Vdc ≥ 250 Vdc CR ≤ 0,1 µF 0,1 µF < CR ≤ 1 µF 8 8 15 15 30 – CR ≤ 0,33 µF 3750 MΩ 7500 MΩ CR > 1 µF 10 – – CR > 0,33 µF 1250 s 2500 s 1) According to CECC 30401-007, test criteria must be met after exposure to damp heat for 21 days. Siemens Matsushita Components 61 B 32 560 … B 32 564 MKT Impedance Z versus frequency f (typical values) Pulse handling capability VR 63 Vdc 100 Vdc 250 Vdc 400 Vdc 420 Vdc 630 Vdc Max. rate of voltage rise Vpp/τ in V/µs (for Vpp = VR) Lead spacing 7,5 mm 10 mm 15 mm 22,5 mm 120 – – – 150 75 50 50 200 150 100 100 275 175 125 125 – – – – 320 – 150 – 27,5 mm – 25 50 60 60 – For Vpp < VR , the permissible voltage rise rate value Vpp/τ may be multiplied by the factor VR/Vpp. Also refer to the calculation example on page 250. VR 63 Vdc 100 Vdc 250 Vdc 400 Vdc 420 Vdc 630 Vdc 62 Pulse characteristic k0 in V2/µs (for Vpp ≤ VR) Lead spacing 7,5 mm 10 mm 15 mm 15 000 – – 30 000 15 000 10 000 100 000 75 000 50 000 220 000 140 000 100 000 – – – 400 000 – 190 000 22,5 mm – 10 000 50 000 100 000 – – 27,5 mm – 5 000 25 000 50 000 50 000 – Siemens Matsushita Components /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 Maximum permissible voltage change per unit of time for non-sinusoidal voltages (pulse, sawtooth). /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 B 32 560 MKT 7,5 Permissible ac voltage Vrms versus frequency f Lead spacing 7,5 mm 63 Vdc/ 40 Vac 100 Vdc/ 63 Vac Vac Vac Vrms Vrms 250Vdc/ 160Vac 400 Vdc/ 200 Vac Vac Vrms Siemens Matsushita Components Vac Vrms 63 MKT B 32 560 7,5 Permissible ac voltage Vrms versus frequency f Lead spacing 7,5 mm /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 630 Vdc/ 400 Vac 64 Siemens Matsushita Components /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 B 32 561 MKT 10 Permissible ac voltage Vrms versus frequency f Lead spacing 10 mm 100 Vdc/ 63 Vac 250 Vdc/ 160 Vac Vac Vrms Vac Vrms 400 Vdc/ 200 Vac Vac Vrms Siemens Matsushita Components 65 MKT B 32 562 15 Permissible ac voltage Vrms versus frequency f Lead spacing 15 mm 250 Vdc/ 160 Vac Vac Vac Vrms Vrms 400 Vdc/200 Vac 630 Vdc/350 Vac Vac Vrms 66 Siemens Matsushita Components /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 100 Vdc/63 Vac /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 B 32 563 MKT 22,5 Permissible ac voltage Vrms versus frequency f Lead spacing 22,5 mm 100 Vdc/ 63 Vac 250 Vdc/ 160 Vac Vac Vrms Vac Vrms 400 Vdc/ 200 Vac Vac Vrms Siemens Matsushita Components 67 MKT B 32 564 27,5 Permissible ac voltage Vrms versus frequency f Lead spacing 27,5 mm 250 Vdc/ 160 Vac /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564 100 Vdc/ 63 Vac 400 Vdc/ 200 Vac Vac Vrms 68 Siemens Matsushita Components